Alliance Laundry Systems HCD020GD2 Manuale utente

Programming

Washer-Extractor

Refer to Page 7 for Model Numbers

CHM495R_SVG

Original Instructions

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com Part No. F8208501ENR10

March 2017

WARNING

Machine installations must comply with minimum

specifications and requirements stated in the appli-

cable Installation Manual, any applicable municipal

building codes, water supply requirements, electrical

wiring regulations and any other relevant statutory

regulations. Due to varied requirements and applica-

ble local codes, this machine must be installed, ad-

justed, and serviced by qualified maintenance per-

sonnel familiar with applicable local codes and the

construction and operation of this type of machinery.

They must also be familiar with the potential hazards

involved. Failure to observe this warning may result

in personal injury, property damage, and/or equip-

ment damage, and will void the warranty.

W820

NOTE: The WARNINGS and IMPORTANT SAFETY IN-

STRUCTIONS appearing in this manual are not meant

to cover all possible conditions and situations that may

occur. Common sense, caution, and care must be exer-

cised when installing, maintaining, or operating the

machine.

Any problems or conditions not understood should be reported to

the dealer, distributor, service agent or the manufacturer.

DO NOT COPY or TRANSMIT

3 Part No. F8208501ENR10

Table of Contents

Model Identification............................................................................... 7

Introduction........................................................................................... 9

Replacement Parts ......................................................................................... 9

Customer Service............................................................................................9

Preliminary Information.......................................................................10

About the Control......................................................................................... 10

Glossary of Terms.........................................................................................10

Power Failure Recovery................................................................................ 10

Control Identification............................................................................11

Display Identification............................................................................12

Light Emitting Diodes (LEDs)....................................................................... 12

Four 7-Segment Digits.................................................................................. 12

Machine Operation...............................................................................13

Start Up....................................................................................................... 13

Ready Mode.................................................................................................13

Partial Vend Mode (Vended Models Only).......................................................13

Signals.........................................................................................................13

Start Mode................................................................................................... 13

Door Locking Mode......................................................................................13

Run Mode.................................................................................................... 13

Changing Cycles...........................................................................................13

Door Unlocking Mode...................................................................................13

End of Cycle Mode....................................................................................... 13

Special Features....................................................................................14

Programming the Control.............................................................................. 14

Collecting Audit Information......................................................................... 14

Production Test Cycle....................................................................................14

Rapid Advance Feature................................................................................. 14

Coin Drop.................................................................................................... 14

OPL Mode................................................................................................... 14

Power Save Mode......................................................................................... 14

written consent of the publisher.

DO NOT COPY or TRANSMIT

4 Part No. F8208501ENR10

Opening the Top Cover......................................................................... 15

Programming the DIP Switch ...............................................................16

Entering the Manual Mode................................................................... 17

How to Enter the Manual Mode......................................................................17

Programming Control...........................................................................18

What Can Be Programmed?........................................................................... 18

Programmable Options Available................................................................... 19

Programming Flowcharts...............................................................................21

Vend Price AtS............................................................................................. 25

Coin #1 Value dEn1...................................................................................... 25

Coin #2 Value dEn2...................................................................................... 25

Error Code ErrS............................................................................................25

Coin Audio Beep CoAU................................................................................25

Card Display Option CArd.............................................................................26

Total # of Machine Cycles CyC......................................................................26

Total # of Rapid Advance Cycles rCyC...........................................................26

Prewash Fill Level PLEU.............................................................................. 26

Wash Fill Level ALEU.................................................................................. 26

Rinse #1, #2 and #3 Fill Level rLEU...............................................................27

Prewash Enable PrEn.................................................................................... 27

Prewash Time PdUr...................................................................................... 27

Wash Time AdUr.......................................................................................... 27

Intermediate Rinse Spins Enable SPEn........................................................... 27

Rinse #2 Enable r2En.................................................................................... 28

Hot Cycle Temperature FH (Heat Enabled Only)............................................. 28

Warm Cycle Temperature FHC (Heat Enabled Only)........................................28

Cycle Pause Enable CyCP (Gravity Drain Models Only).................................. 28

Leak Detection During Cycle Enable LdEn .................................................... 28

Slow Drain Detection During Cycle Enable SdEn ........................................... 29

Slow Drain Detection Adjustment SdAd ........................................................ 29

Number of Balance Retries bALr (Design 2 and 3 Models Only).......................29

Leak Detection Test Ldt.................................................................................29

Balance Weight Test bALt (F-speed Design 1 Models Only)............................. 30

DC Bus Display Test dCbt (Design 2 and 3 Models Only)................................ 30

DIP Switch Test dIPt..................................................................................... 30

Rapid Advance rAPd.....................................................................................30

Exit Manual Mode End..................................................................................30

Production Test Cycle........................................................................... 32

To Enter Production Test Cycle...................................................................... 32

To Exit Production Test Cycle........................................................................ 33

Error Codes..........................................................................................36

DO NOT COPY or TRANSMIT

5 Part No. F8208501ENR10

Power Fail Recovery............................................................................. 38

Default Cycles.......................................................................................39

DO NOT COPY or TRANSMIT

6 Part No. F8208501ENR10

Model Identification

Information in this manual is applicable to these models:

Models

20 Pound HCD020GD2

HCH020GNF

HCL020GC2

HCL020GD2

HCL020GN2

HCL020GNF

HCN020GC2

HCN020GD2

HCN020GE2

HCN020GN2

HCN020GNF

HCN020GNV

HCN020GX2

HCN020GY2

HCU020GC2

HCU020GD2

HCU020GE2

HCU020GL2

HCU020GN2

HCU020GNF

HCU020GX2

HCU020GY2

HCZ020GN2

HCZ020GNF

ICN020GNF

SCL020GC2

SCL020GN2

SCL020GNF

SCL020GNV

SCN020GC2

SCN020GD2

SCN020GE2

SCN020GN2

SCN020GNF

SCN020GX2

SCN020GY2

SCU020GC2

SCU020GD2

SCU020GE2

SCU020GL2

SCU020GN2

SCU020GNF

SCU020GNV

SCU020GX2

SCU020GY2

SCZ020GN2

SCZ020GNF

UCH020GNF

UCH020GNV

UCL020GN2

UCL020GNF

UCL020GNV

UCN020GN2

UCN020GNF

UCN020GNV

UCU020GN2

UCU020GNF

UCU020GNV

UCZ020GN2

UCZ020GNF

30 Pound HCH030GNF

HCL030GN2

HCL030GNF

HCN030GC2

HCN030GD2

HCN030GE2

HCN030GN2

HCN030GNF

HCN030GNV

HCN030GX2

HCN030GY2

HCU030GC2

HCU030GD2

HCU030GE2

HCU030GL2

HCU030GN2

HCU030GNF

HCU030GNV

HCU030GX2

HCU030GY2

HCZ030GN2

HCZ030GNF

ICN030GNF

SCD030GD2

SCH030GCF

SCH030GNF

SCH030GNV

SCL030GC2

SCL030GCF

SCL030GN2

SCL030GNF

SCL030GNV

SCN030GC2

SCN030GD2

SCN030GE2

SCN030GN2

SCN030GNF

SCN030GNV

SCN030GX2

SCN030GY2

SCU030GC2

SCU030GD2

SCU030GE2

SCU030GL2

SCU030GN2

SCU030GNF

SCU030GNV

SCU030GX2

SCU030GY2

UCH030GNF

UCH030GNV

UCL030GN2

UCL030GNF

UCL030GNV

SCZ030GN2

SCZ030GNF

UCN030GN2

UCN030GNF

UCN030GNV

UCU030GN2

UCU030GNF

UCU030GNV

UCZ030GN2

UCZ030GNF

VCU030GN2

40 Pound HCB040GNF

HCH040GNF

HCH040GNV

HCL040GN2

HCL040GNF

HCL040GNV

HCN040GC2

HCN040GD2

HCN040GE2

HCN040GN2

HCN040GNF

HCN040GNV

HCN040GX2

HCN040GY2

HCU040GC2

HCU040GD2

HCU040GE2

HCU040GL2

HCU040GN2

HCU040GNF

HCU040GNV

HCU040GX2

HCU040GY2

ICN040GNF

SCB040GNF

SCD040GD2

SCH040GCF

SCH040GNF

SCH040GNV

SCL040GC2

SCL040GCF

SCL040GN2

SCL040GNF

SCL040GNV

SCN040GC2

SCN040GD2

SCN040GE2

SCN040GN2

SCN040GNF

SCN040GNV

SCN040GX2

SCN040GY2

SCU040GC2

SCU040GD2

SCU040GE2

SCU040GL2

SCU040GN2

SCU040GNF

SCU040GNV

SCU040GX2

SCU040GY2

UCH040GNF

UCH040GNV

UCL040GN2

UCL040GNF

UCL040GNV

UCN040GN2

UCN040GNF

UCN040GNV

UCU040GN2

UCU040GNF

UCU040GNV

VCU040GN2

Table continues...

Model Identification

DO NOT COPY or TRANSMIT

7 Part No. F8208501ENR10

Models

60 Pound HCH060GNF

HCH060GNV

HCL060GN2

HCL060GNF

HCL060GNV

HCN060GC2

HCN060GCF

HCN060GD2

HCN060GE2

HCN060GN2

HCN060GNF

HCN060GNV

HCN060GX2

HCN060GY2

HCU060GC2

HCU060GD2

HCU060GE2

HCU060GL2

HCU060GN2

HCU060GNF

HCU060GNV

HCU060GX2

HCU060GY2

ICN060GNF

SCD060GD2

SCH060GNF

SCH060GNV

SCL060GC2

SCL060GN2

SCL060GNF

SCL060GNV

SCN060GC2

SCN060GCF

SCN060GD2

SCN060GDF

SCN060GE2

SCN060GN2

SCN060GNF

SCN060GNV

SCN060GY2

SCU060GC2

SCU060GD2

SCU060GE2

SCU060GL2

SCU060GN2

SCU060GNF

SCU060GNV

SCU060GX2

SCU060GY2

UCH060GNF

UCH060GNV

UCL060GN2

UCL060GNF

UCL060GNV

UCN060GN2

UCN060GNF

UCN060GNV

UCU060GN2

UCU060GNF

UCU060GNV

VCU060GN2

80 Pound HCH080GNF

HCL080GNF

HCN080GCF

HCN080GDF

HCN080GEF

HCN080GNF

HCN080GXF

HCN080GYF

HCU080GCF

HCU080GDF

HCU080GEF

HCU080GLF

HCU080GNF

HCU080GXF

HCU080GYF

ICN080GNF

SCH080GNF

SCL080GNF

SCN080GCF

SCN080GDF

SCN080GEF

SCN080GNF

SCN080GXF

SCN080GYF

SCU080GCF

SCU080GDF

SCU080GEF

SCU080GLF

SCU080GNF

SCU080GXF

SCU080GYF

UCH080GNF

UCL080GNF

UCN080GNF

UCU080GNF

VCU080GNF

100 Pound HCH100GNF

HCL100GNF

HCN100GNF

ICN100GNF

SCH100GNF

SCL100GNF

SCN100GNF

UCH100GNF

UCL100GNF UCN100GNF

Model Identification

DO NOT COPY or TRANSMIT

8 Part No. F8208501ENR10

Introduction

Replacement Parts

If literature or replacement parts are required, contact the source

from which the machine was purchased or contact Alliance Laun-

dry Systems at +1 (920) 748-3950 for the name and address of

the nearest authorized parts distributor.

Customer Service

For technical assistance, contact your local distributor or contact:

Alliance Laundry Systems

Shepard Street

P.O. Box 990

Ripon, WI 54971-0990

U.S.A.

www.alliancelaundry.com

Phone: +1 (920) 748-3121 Ripon, Wisconsin

Introduction

DO NOT COPY or TRANSMIT

9 Part No. F8208501ENR10

Preliminary Information

About the Control

This control is a programmable computer that lets the owner con-

trol most machine features by setting dip switches and pressing

buttons on the back of the control.

The control allows the owner to program custom cycles, set vend

prices, retrieve audit information, run tests and other programma-

ble features. Refer to Programming the Control for a list of fea-

tures.

IMPORTANT: In the event of a power failure, the control

will not have to be reprogrammed. It is designed with a

memory system that will remember how it was pro-

grammed until the electrical power is restored.

IMPORTANT: It is extremely important that the machine

has a good ground connection and that all mechanical

and electrical connections to the control are made be-

fore applying power to or operating the machine.

Glossary of Terms

The following are a few terms and abbreviations to learn. These

are referred to throughout the instructions.

Display – This term refers to the window area of the control that

displays words and values.

LED (Light Emitting Diode) – This term refers to the lights next

to the keypads and status words of the control.

Power Failure Recovery

If a cycle is in progress and the power fails, the cycle status is

saved in memory. When the power recovers, the machine will re-

sume into the previously active cycle if the power outage is less

than five (5) seconds and the door is closed and locked.

If the length of the power failure is greater than five (5) seconds,

the control will enter Start Mode and require pressing the START

switch. If the power failure is greater than five (5) seconds and

OPL Mode is enabled, the cycle can not be resumed.

Preliminary Information

DO NOT COPY or TRANSMIT

10 Part No. F8208501ENR10

Altri manuali per HCD020GD2

Questo manuale è adatto per i seguenti modelli

187

Indice

Altri manuali Alliance Laundry Systems Rondella

Alliance Laundry Systems

Alliance Laundry Systems IYB180J Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems SH180-QED-SELECT Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems 800970R1 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems Hardmount Coin and OPL Manuale di installazione e funzionamento

Alliance Laundry Systems

Alliance Laundry Systems UW60TV Istruzioni operative

Alliance Laundry Systems

Alliance Laundry Systems NetMaser Series Istruzioni operative

Alliance Laundry Systems

Alliance Laundry Systems WF065B Guida alla manutenzione e all'assistenza

Alliance Laundry Systems

Alliance Laundry Systems D1528ENR3 Guida alla risoluzione dei problemi

Alliance Laundry Systems

Alliance Laundry Systems UW35S2 Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems F232135R12 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems 9001014R7 Guida all'installazione

Alliance Laundry Systems

Alliance Laundry Systems 805413R1 Guida

Alliance Laundry Systems

Alliance Laundry Systems TC5003WN Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems HWNLX2SP111CW01 Istruzioni operative

Alliance Laundry Systems

Alliance Laundry Systems HC18 Guida alla manutenzione e all'assistenza

Alliance Laundry Systems

Alliance Laundry Systems EC001F Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems NetMaster HC18NC2 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems PHM1397C Guida alla risoluzione dei problemi

Alliance Laundry Systems

Alliance Laundry Systems PA20 X CONTROL Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems H370I Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems CHM166C Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems DCG020ND Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems CPD6C Manuale di installazione e funzionamento

Alliance Laundry Systems

Alliance Laundry Systems LWS01A* series Istruzioni operative

Manuali Rondella popolari di altre marche

Tricity Bendix

Tricity Bendix AW 1000 W Guida del prodotto

Panasonic

Panasonic NA-F60L5WRB Manuale utente

GE WSLP1500 Manuale

Electrolux

Electrolux EWF1284EDW Manuale utente

Bosch

Bosch WAN2829BSN Manuale utente

LG TV2516DV3B Manuale utente

LG TH2517DSAV Manuale utente

VESTEL

VESTEL CMH-XL 7510 TE Manuale utente

AEG

AEG 74335 Manuale operativo

Johnson

Johnson JWF721A Manuale utente

Beko

Beko WTE7604XLW0 Manuale utente

Danby

Danby DTT100A1WDB Istruzioni per il montaggio

Amica

Amica WA 14 Ex Manuale utente

Daewoo

Daewoo DWD-F1222 Manuale utente

Bosch

Bosch WAS28461AU Manuale utente

Miele

Miele PW 6080 Vario Manuale utente

Finlux

Finlux FLX108CF220 Manuale utente

Whirlpool

Whirlpool 3LBR5132AN0 Manuale utente