Alloy POEFE24T Manuale utente

POEFE24T User Manual

User Manual

POEFE24T

24 Port Fast Ethernet

PoE Switch

Version 1.1

October 2010

POEFE24T User Manual

Contents

1. Introduction ..............................................................4

2. Checklist...................................................................4

3. Installation ................................................................5

3.1 Installation Method ........................................................................ 5

3.2 Desktop or Shelf Installation...........................................................5

3.3 Rack Installation .............................................................................5

4. Powering on the Switch..................................................6

5. LED Description...........................................................6

6. Network Connection .....................................................7

7. Technical Specifications..................................................8

Appendix A. RJ-45 Connections ............................................9

POEFE24T User Manual

Caution

Electronic Circuit devices are sensitive to static electricity. Dry weather conditions or walking

across a carpeted floor may cause you to acquire a static electric charge.

To protect your switch, always:

•Touch the metal chassis of your computer to ground the static electrical charge before

you handle the switch.

•Pick up the switch by holding it on the left and right edges only.

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment.

European Community (CE) Electromagnetic Compatibility Directive

This equipment has been tested and found to comply with the protection requirements of

European Emission Standard EN55022/EN60555-2 and the Generic European Immunity

Standard EN50082-1.

EMC:

Australian C-Tick Compliance.

This equipment is compliant with the required Australian C-Tick standards

EN55022(1988)/CISPR-22(1985) class A

EN60555-2(1995) class A

EN60555-3

IEC1000-4-2(1995) 4K V CD, 8KV, AD

IEC1000-4-3(1995) 3V/m

IEC1000-4-4(1995) 1KV – (power line), 0.5KV – (signal line)

POEFE24T User Manual

1. Introduction

The POEFE24T is an unmanaged low cost Fast Ethernet Power Over Ethernet switch. The

switch consists of 24x 10/100Mbps PoE ports. All ports are auto sensing, auto MDI/X ports

allowing easy connectivity to your existing switching infrastructure and your PD PoE devices,

such as IP Phones, Wireless Access Points and IP Video Cameras. All ports support up to

15.4W of power, with the switch supporting 7.7W per port at full load. The POEFE24T

supports up to 185W in total.

The POEFE24T is the ideal solution for adding low cost PoE capability to your newly deployed

IP PBX and IP Phone infrastructure.

Features

⇒Supports PoE power up to 15.4W for each PoE port

⇒Supports PoE power up to 185W for all PoE ports

⇒Supports PoE IEEE802.3af compliant PDs

⇒Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for Half-

duplex Mode

⇒8K MAC address with auto-learning and auto-aging

⇒LED indicators for monitoring power, link, activity and speed

⇒Internal universal power supply

2. Checklist

Before you start installing your equipment, verify that the package contains the following:

The POEFE24T – Fast Ethernet POE Switch

Rack Mount kit with appropriate mounting screws

Power Cable

This Users Manual CD-ROM

Please notify your supplier immediately if any of the aforementioned items are missing or

damaged.

POEFE24T User Manual

3. Installation

3.1 Installation Method

The site where you install the switch may greatly affect its performance. When installing,

please take the following into consideration.

-Install the switch in a cool, dry place. See technical specifications for the acceptable

temperature and humidity operating ranges.

-Install the switch on a secure, level surface that can support its weight, at least 5Kg.

-Before connecting the Power Cord please ensure the appropriate voltage switch is

set, this switch can be found at the back of the POEFE24T.

-Leave at least 10cm of space at the front and rear of the switch to ensure adequate

ventilation.

3.2 Desktop or Shelf Installation

When installing the switch on a shelf on desktop please ensure guidelines are above are

following, including level surface and adequate ventilation.

3.3 Rack Installation

The POEFE24T is a rack mountable switch and can be installed in an EIA-19 based equipment

rack. First install the provided rack mount brackets onto each side of the switch using the

screws provided. Using the screws provided with your rack mount the switch into your

equipment rack.

Fig. 1 Rack Mount kit installation

POEFE24T User Manual

4. Powering on the Switch

Before powering on the switch please ensure that the voltage range switch at the rear of the

switch is set to the appropriate voltage range for your country. Voltage switch can be set to

100V or 220V AC.

Note:

Please double check and ensure power voltage is correctly configured, if set incorrectly

damage to the switch is possible.

5. LED Description

LED Colour Function

Power On Appropriate power is supplied

Off Power is not available

LINK

On A valid link is established

Blink Traffic is present on port

Off No link established

POE

On PD PoE device has successfully connected

to the port.

Off No POE device connected

Fig. 2 Power Switch

POEFE24T User Manual

6. Network Connection

Connect your devices (computer, router, switch, IP Phone, Wireless Access Point, IP Camera

etc.) to the ports with a CAT-5/CAT-5e/CAT-6 network cable. Since the switch supports Auto

MDI/MDI-X you can use either a straight through or cross-over network cable.

Fig. 3 Front panel of switch

POEFE24T User Manual

7. Technical Specifications

Model POEFE24T

Standards IEEE802.3 10Base-T, IEEE802.3u 100Base-TX

Number of Ports 24 x 10/100Mbps Auto-Negotiation ports

Network Media

10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)

EIA/TIA-568 100Ω STP (maximum 100m)

100BASE-TX: UTP category 5, 5e cable (maximum 100m)

EIA/TIA-568 100Ω STP (maximum 100m)

Transfer Method Store-and-Forward

Switching Capacity 4.8G

MAC Address Table 8K

Frame Filtering and

Forward Rate

10Mbps: 14880pps

100Mbps: 148800pps

POE Up to 15.4W per port

7.7W per port at full load

POE Pins POE delivered on pins 4, 5, 7 and 8

LED indicators Link per port

Power

POE per port

Dimensions (W × D × H) 441 x 208 x 44 (mm)

Environment

Operating Temperature: 0°C - 40°C

Storage Temperature: -40°C - 70°C

Operating Humidity: 10%~90% non-condensing

Storage humidity: 5%~90% non-condensing

Certification C-Tick, CE, FCC, RoHS

POEFE24T User Manual

Appendix A. RJ-45 Connections

RJ-45 Connector pin out

Pin no. MDI-I signal MDI-X signal

1 TX+ RX+

2 TX- RX-

RX+

TX+

not used

RX-

TX-

7 not used not used

8 not used not used

Below is a diagram of a typical straight through and cross-over cable connection:

Fig. 4 RJ-45 Connectors, switch and cable views

Fig. 5 Straight Through Cable connection

Fig. 6 Cross-Over Cable connection

Indice

Altri manuali Alloy Interruttore

Alloy

Alloy ESM-24T02M Manuale utente

Alloy

Alloy POEGE8T Manuale utente

Alloy

Alloy APS-10T2SFP Manuale utente

Alloy

Alloy AWPS-8T1SFP Manuale utente

Alloy

Alloy POEGEM12T2SFP Manuale utente

Alloy

Alloy AS1000 Series Manuale utente

Alloy

Alloy POEFE404 Manuale utente

Alloy

Alloy GSS-8T2SFPV2 Manuale utente

Alloy

Alloy POEFE8TV2 Manuale utente

Alloy

Alloy GSS-24T2SFP Manuale utente

Alloy

Alloy POEFE8T Manuale utente

Alloy

Alloy APS-26T6SFP Manuale utente

Alloy

Alloy SmartHome AH-HUB3 Manuale utente

Alloy

Alloy 16-PORT GIGABIT WEB SMART SWITCH GSS-16T2SFP Manuale utente

Alloy

Alloy POEFE24TV2 Manuale utente

Alloy

Alloy GSM-16T2SFP Manuale utente

Alloy

Alloy SmartHome Hub3 Manuale utente

Alloy

Alloy GSS-16T4SFP Manuale utente

Alloy

Alloy SmartHome AH-HUB3 Manuale utente

Alloy

Alloy AMS-10T2SFP Manuale utente

Alloy

Alloy GSS-8T2SFP Manuale utente

Alloy

Alloy MS888G2 Manuale utente

Alloy

Alloy AS5010-P Manuale utente

Alloy

Alloy 16-PORT GIGABIT WEB SMART SWITCH GSS-16T2SFP Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente