Almot 870N Manuale di istruzioni
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it
870N
CONTROL UNIT
FOR MOTORS 230 VAC AWNINGS, SHUTTERS, VASISTAS, LIGHTS
INSTRUCTION MANUAL AND USE
ENGLISH
Version 2 10.05.2018
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it
WARNING READ CAREFULLY THE FOLLOWING SAFETY INDICATIONS BEFORE TO START THE INSTALLA-
TION OF THIS DEVICE; THEY ARE USEFUL TO PREVENT ANY ELECTRICAL CONTACT, INJURY AND OTHER
PROBLEMS. KEEP THIS MANUAL FOR OTHER CONSULTATIONS.
The control units are intended exclusively to the control of the weather for the automac movement of
the awnings, shuers, vasistas and lights. The use for applicaons which are dierent from the ones indi-
cated must be authorized by the manufacturer, aer the technical test of the applicaon.
The installaon of the device must be made by technical and qualied sta.
Aer having removed the packaging, check that the device is intact.
Plasc bags, styrofoam, small metallic components as nails, clips, etc. have to be kept out of reach of
children, because they might be dangerous.
Before to connect the device, verify that the electrical supply that you use, has the same features
indicated in the label with the technical infos, applied on the device.
This device has been intended just and exclusively for the use for which it has been programmed
and the manufacturer can not be held accountable for the damages caused by its improper use.
The installaon of the device has to be made according to the instrucons of the manufacturer. Non
-compliance with these rules can compromise the safety.
The implementaon of the electrical installaon of voltage supply has to be made according to the
current rules.
To avoid any danger of injuries or death caused by the voltage supply, before implemenng any ope-
raon of wiring or regulaon, turn o the voltage from the supply line.
To assure an eecve separaon from the net we suggest to install a momentary bipolar switch
(buon) approved. At the beginning of the command line a general omnipolar switch of supply with
input of the contact of at least 3mm, must be installed.
Do not clean or wash the device with solvent or jets of water. Do not immerse into water.
Warning: in case of damage or malfuncon, turn o the device from the general switch and call a
qualied technician.
Every repair have to be implemented only by qualied sta in an help centre authorized by the ma-
nufacturer.
Before implemenng any operaon of cleaning or maintenance, be sure to disconnect the device
from the net. For further safety we suggest to remove the electrical connecon.
Request always and exclusively the use of original replacements. The non-compliance with this rule
could compromise the safety and undo the benets of the warranty applied on the device.
In case of problems or doubts during the intallaon of the funconing, address to your retailer of
trust or directly to the manufacturer.
1. SAFETY INTICATIONS
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it
2.0 TECHNICAL DATAS
PARAMETERS 870
VOLTAGE SUPPLY 230 VAC/50Hz
MAX POWER OUTGOING 500 W
TEMPERATURE OF EXERCISE -20 / +70°C
PROTECTION FUSE PTC
WORKING TIME* 40/60/120 SEC
WIND THERSHOLD 12—25—35 Km/h
MAX TX MEMORIZABLES 15
RX RADIO FREQUENCY 433,92 Mhz
PROTECTION DEGREE IP 55
SIZE 115 x 35 x 23 mm
1
2.1 COMPOSITION OF THE PRODUCT AND DIAGRAM OF CONNECTION
CONTROL UNIT 870N
Seng: AWNING
08880870N: control unit for the
managing of shuers, awnings,
vasistas and light.
*Working me:
Vasistas: 40 / 120 Sec.
Shuer: 40 / 120 Sec.
Awning: 60 / 120 Sec.
1 = +12V
2 = OPEN/STOP or STEP BY STEP
3 = CLOSE or CLOSE/STOP
4 = COMMON
Seng: SHUTTER
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it
2.1 COMPOSITION OF THE PRODUCT AND DIAGRAM OF CONNECTION
2
CONTROL UNIT 870N
2.2 FUNZIONI DIP SWITCH 870N
DIP 1 DIP 2 DIP 3 FUNCTION
OFF OFF OFF SETTING AWNING: INPUT ANEMOMETER and INPUT STEP BY STEP. Working me 60 se-
conds. REGULATION WIND THERSHOLD BY TX
ON OFF OFF SETTING VASISTAS: INPUT RAIN SENSOR and INPUT OPEN/CLOSE and CLOSE/STOP. Wor-
king me 40 seconds.
OFF ON OFF SETTING SHUTTER: INPUT. OPEN/STOP and CLOSE/STOP. Working me 40 seconds.
OFF OFF ON SETTING AWNING: INPUT ANEMOMETER and INPUT STEP BY STEP. Working me 120
seconds. REGULATION WIND THERSHOLD BY TX
ON OFF ON SETTING VASISTAS: INPUT RAIN SENSOR and INPUT OPEN/CLOSE and CLOSE/STOP. Wor-
king me 120 seconds.
OFF ON ON SETTING SHUTTER: INPUT. OPEN/STOP and CLOSE/STOP. Working me 120 seconds.
ON ON OFF LIGHTS SETTING: INPUT ON/OFF LIGHT 1 and ON/OFF LIGHT 2.
ON ON ON LIGHTS SETTING: INPUT ON/OFF LIGHT 1 and ON/OFF LIGHT 2.
WARNING: USE THE LIGHT SETTING IF THE LIGHTS ARE PRESENTS, RISK OF DAMAGING THE CONTROL UNIT IF THE MOTOR
GETS CONNECTED
Seng: VASISTAS
Seng: LIGHTS
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it 3
DIP 4 FUNCTION
OFF Sengs of the working mes STANDARD.
ON Sengs of the TEST mings of work (the wor-
king mes are reduced to 10—12 seconds).
2.3 FUNCTIONS DIP SWITCH 870N
3.0 GENERAL RULES OF FUNCTIONING
During the wiring strictly respect the diagram of connecon, a wrong connecon could damage the
installaon. Follow the diagram more appropriate to the installaon. (paragraph 2.1)
Do not use, for the command, stable posion switches.
Do not exceed 50 mt of cable between the control unit and the anemometer.
Aer supplying the control unit (in case of installaon on an awning) posion the awning on half of
the run, rotate the sensor and check that aer the alarm happened (ashing red led), the awning goes up
(closing). In case that it goes backwards, invert the wires on the MOTOR OPENS clamp, to the MOTOR
CLOSES clamp.
Posion the sensor in an opmal posion for receiving the wind, as close to the awning as possible.
If during the installaon, with the connuous opening and closing of the awning, shuer or vasistas,
the motor gets stuck, this is not because of a damage of the board, but because of the thermic protector
contained in the motor. Wait unl the motor has cooled down and try again.
4. 0 PROGRAMMING FIRST TX MASTER BY REMOTE (IF THERE IS NO TX STORED)
4.1 PROGRAMMING OF OTHER TX BY MASTER TRANSMITTER
DIP 5 FUNCTION
OFF Funconing of the command switches IMPUL-
SIVE.
ON Funconing command switches to DEAD
MAN.
1) Supply the control unit 2) The motor will do
two short opposite
movements which indi-
cate that there are no
TX stored in the control
unit’s memory
3) Within a few seconds
press the STOP switch of
the TX to memorize.
4) The motor will do two
short movements which
indicate that the TX has
been memorized. Release
the STOP of the
TX.
5) Programming accompli-
shed.
1) When the control unit
has been supplied, press
and hold the hidden
switch of the TX master
already stored.
2) The motor will do
two short movements
which indicate the
storing has begun.
4) Within a few se-
conds press the STOP
switch of the TX to
memorize.
5) The motor will do
two short move-
ments which indicate
that the TX has been
memorized.
6) Programming
accomplished.
3) Release the hidden
switch of the TX.
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it 4
4.3 REGULATION OF THE WIND BY TX (IF SET BY DIP SWITCH)
4.2 DELETING A TX BY TRANSMITTER
1) Press and hold the
PROGRAMMING
switch of a TX already
stored.
2) Aer some se-
conds the motor will
do TWO short oppo-
site movements.
3) Release the PRO-
GRAMMING switch of
the TX already stored.
4) Press IMMEDIATLY
the STOP switch of the
TX to store.
5) The motor will do
TWO short opposite
movements.
6) RESET accompli-
shed.
1) Press and hold
the PROGRAM-
MING switch of a
TX already stored.
2) Aer some se-
conds the motor will
do TWO short oppo-
site movements.
3) Aer some seconds
the motor will do TWO
further short opposite
movements.
4) Release the PRO-
GRAMMING switch of
the TX altready stored.
5) If the CLIMB switch
is pressed, 15 km/h
will be set. Choose
just one switch.
6) If the STOP
switch is pressed,
25 km/h will be set.
Choose just one
switch .
7) If you pree the
DESCENT switch, 35
km/h will be set.
Choose just one
switch.
8) Once you pressed the
wanted switch, the mo-
tor will do TWO short
opposite movements of
conrmaon.
9) REGULATION OF
THE WIND SPEED
ACCOMPLISHED.
4.4 INVERSION OF THE MOTOR MOVEMENT BY TX
1) Press and hold the
PROGRAMMING
switch of the TX al-
ready stored.
2) Aer a few seconds
the motor will do TWO
short opposite move-
ments. 1 BEEP
3) Aer a few seconds
the motor will do
TWO further short
opposite movements.
2 BEEP
4) Aer a few seconds
the motor will do TWO
further short opposite
movements. 3 BEEP
5) Release the PRO-
GRAMMING switch of
the TX altready stored.
6) INVERSION OF
THE MOTION AC-
COMPLISHED.
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it 5
4.5 MEMORIZATION OF A TX BY CONTROL UNIT CENTRALE 870N
4.7 RESET OF ALL THE TX BY CONTROL UNIT 870N
4.8 RESET TOTALE
4.6 DELETING A TX BY CONTROL UNIT 870N
1) When the control unit
has been supplied, press
and holdthe P1 switch for
3 seconds and release.
2) The control unit will
make a long sound.
4) Press IMMEDIATLY the
STOP switch of the TX to
memorize.
5) The motor will do TWO
short opposite move-
ments.
6) PROGRAMMING ac-
complished
BEEEEEEP
1) When the control unit
has been supplied, press
and holdthe P1 switch for
3 seconds and release.
2) The control unit will
make a long sound.
4) Press IMMEDIATLY the
STOP switch of the TX to
delete.
5) The motor will do TWO
short opposite move-
ments.
6) RESET accomplished
BEEEEEEP
1) When the control unit
has been supplied, press
and hold the P1 switch .
2) Aer many seconds,
The motor will do TWO
short opposite move-
ments.
3) Release the programming
P1 switch.
6) RESET accomplished
1) Close the contact
between the COM
input and the PP
input of the control
unit 870N
2) Supply the control
unit.
3) Aer many se-
conds, The motor will
do FOUR short oppo-
site consecuve mo-
vements.
4) OPEN the contact
between the COM input
and the PP input of the
control unit 870N
5) Aer many se-
conds, The motor will
do ONE further short
opposite movement.
6) Aer some se-
conds the motor
will do TWO further
short opposite mo-
vements.
S.G. Eleronica S.r.l - Via E. Ferrari , 28 - 30037 Scorzè (VE) Italy - Tel +39 041 5841973 Fax +39 041 5841979 - www.almot.it - info@almot.it 6
6.0 COMPLIACE CERTIFICATE ON THE EU DIRECTIVES
S.G. Eleronica S.r.l. - Via Ferrari 28
30037 Scorzè, Venezia - ITALY
P. IVA 02272310273
Tel. +39 041 5841973 - Fax. +39 041 5841979
COMPLIACE DECLARATION
(direcve 89/392 CEE, annex II, parte B)
S. G. Eleronica srl declares that the following control unit:
08880870N
Are in compliance with the rules set out in the direcves 89/336/EEC, 92/31/EEC, 93/68/EEC about the
electromagnec compability. The following harmonised standards have been aplied:
EN 60335-1, EN 60204-1, EN 55014, EN 6100-3-2, EN 6100-3-3, EN 6100-4-2, EN 6100-4-4, ENV 50140,
EN 50081-1, EN 50082-1
Declares at the same me that it is forbidden to put into service the abovemenoned products before
that the machine to which they are incorporated or are part of, has not been idened and has not been
declared in accordance with the condions requested by the direcve 89/392 CEE and to the naonal le-
gislaon of applicaon, that is unl the material in queson of this declaraon will not be kept together
with the nal machine.
Scorzè, 10/05/2018
Sign of the Legal Representave
Sandro Zono
5.0 WARNINGS ABOUT THE FUNCTIONING
- In case that you are using a sun/wind radio sensor (940), for a correct use of the SUN funcon the aw-
ning has to do a complete cycle, without any interrupon from the nal user (ex. Half opening or vice-
versa).
- Always connect just one control unit at the me, to avoid any accidental storing on other control units.
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Almot Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
