Alpha Networks WUS-N10 Manuale utente
1
ALPHA
WUS-N10
USB wifi module
User’s Manual
Release 0.1
1
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
2
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users. The final end product must be labeled in a visible
area with the following: “Contains FCC ID: RRKWUSN10B1 ”. The grantee's FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
1
Introduction
The WUS-N10 which is based on the RT3070, is a 802.11 b/g/n wireless embedded Mini-PCI module for
AP/ Router + AP. WUS-N10 will be a RF module ofAP board. It has greater throughput at longer range. The
WUS-N10 is a green product.
Features
yCompatible with IEEE 802.11n draft 2.0 standard to provide up to 150Mbps data rate.
yCompatible with IEEE 802.11g standard to provide up to wireless 54Mbps data rate
yCompatible with IEEE 802.11b standard to provide up to wireless 11Mbps data rate
yOperation at 2.4 ~ 2.5GHz frequency band to meet worldwide regulations
yDynamic date rate scaling at 6, 9, 12, 18, 24, 36, 48, 54 for IEEE 802.11g.
yDynamic date rate scaling at 1, 2, 5.5, and 11Mbps for IEEE 802.11b
yMaximum reliability, throughput and connectivity with automatic data rate switching
ySupport wireless data encryption with 64/128-bit WEP for security
ySupport infrastructure networks via Access Point and ad-hoc network via peer-to-peer communication
ySupport WEP, 802.1x, WPA and WPA2 enhanced security
yFriendly user configuration and utilities
yDrivers support Windows 2K, XP 32/64-bit, Vista 32/ 64-bit, MAC OS and Linux
ySupport external WPS button to connect Access Point easily
yHigh speed USB 2.0 interface
yRoHS compliant
yIntegrated antenna
ySupport Xlink global networking gaming
yInteroperability, driver backward compatibility
2
Installation
yTurn on the computer and Insert the Alpha WUS-N10 Driver CD in the CD-ROM drive
yWhen the auto run screen appears, click Install Drivers.
The Install Shield Wizard window will appear.
yBy default setup will install to the default location: To install to a different location click Browse and
specify the location.
ySelect the Program Files folder location
yInsert the adapter into an available USB port on your computer.
yThe Wireless Connection Wizard will now appear.
yTo connect to your network using the WPS push button configuration method, click the virtual button
as shown in the screenshot.
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
