Alphacool Heatmaster 2 Manuale utente

Alphacool International GmbH

Heatmaster 2

Operating Manual

Heatmaster 2

reproduction of any kind, except a copy of the end user customer, requires the written permission of the

Alphacool International Gmbh. This manual is written according to the technical standards at the time of

printing.

Errors, emissions and printing errors excepted

Heatmaster 2

Contents

INTRODUCTION ________________________________________________________5

EXTENT OF DELIVERY___________________________________________________5

WARRANTY____________________________________________________________5

SAFETY NOTICE________________________________________________________6

INTENDED USE_________________________________________________________6

SYSTEM REQUIREMENTS________________________________________________6

SOCKET ASSIGNMENT __________________________________________________7

Overview _____________________________________________________________________________ 7

Power supply _________________________________________________________________________ 7

Fan channels / pumps / slow sensors _____________________________________________________ 7

Pumps______________________________________________________________________________ 8

Flow rate sensors _____________________________________________________________________ 8

Connection array ______________________________________________________________________ 8

USB________________________________________________________________________________ 8

HM BUS ____________________________________________________________________________ 9

Emergency shutdown__________________________________________________________________ 9

PC shut down ________________________________________________________________________ 9

NTC 1 -6 temperature sensors___________________________________________________________ 9

Water level __________________________________________________________________________ 9

LED 1 silent alarm ____________________________________________________________________ 9

LED 2 alarm _________________________________________________________________________ 9

LED 3 warning _______________________________________________________________________ 9

Relay 1-3 ___________________________________________________________________________ 9

Button 1-3 ___________________________________________________________________________ 9

Heatmaster reset _____________________________________________________________________ 9

5V Standby __________________________________________________________________________ 9

12V and 5V output ____________________________________________________________________ 9

INSTALLATION ________________________________________________________10

Hardware installation __________________________________________________________________ 10

Software installation___________________________________________________________________ 10

USE OF THE SOFTWARE________________________________________________16

General configuration _________________________________________________________________ 16

Heatmaster 2

Name _____________________________________________________________________________ 16

Temperature unit ____________________________________________________________________ 16

Language __________________________________________________________________________ 16

Data request interval__________________________________________________________________ 16

Switching time_______________________________________________________________________ 16

Display configuration__________________________________________________________________ 17

Brightness in sleep mode ______________________________________________________________ 17

Brightness of stand-by lighting __________________________________________________________ 17

Standby time________________________________________________________________________ 17

Fan configuration _____________________________________________________________________ 17

Name _____________________________________________________________________________ 17

Status _____________________________________________________________________________ 17

Speed monitoring ____________________________________________________________________ 17

Fan switch-off in case of failure _________________________________________________________ 17

Action in case of fan failure ____________________________________________________________ 17

Determine Min. / Max. speed ___________________________________________________________ 17

Speed factor ________________________________________________________________________ 18

Manual temperature control ____________________________________________________________ 18

Automatic temperature control __________________________________________________________ 18

Temperature sensors configuration______________________________________________________ 18

Name: _____________________________________________________________________________ 18

Status _____________________________________________________________________________ 18

Emergency shutdown_________________________________________________________________ 18

Settings____________________________________________________________________________ 18

Temperature values __________________________________________________________________ 19

Pump / flow rate sensor configuration____________________________________________________ 19

Name _____________________________________________________________________________ 19

Status _____________________________________________________________________________ 19

Type ______________________________________________________________________________ 19

Factor _____________________________________________________________________________ 19

Pump settings_______________________________________________________________________ 19

Flow rate sensor settings ______________________________________________________________ 19

Coolant level control configuration ______________________________________________________ 20

Name _____________________________________________________________________________ 20

Status _____________________________________________________________________________ 20

Type ______________________________________________________________________________ 20

Action in case of critical coolant level_____________________________________________________ 20

Orientation _________________________________________________________________________ 20

Alarm settings_______________________________________________________________________ 20

Calibrate analogue sensor now _________________________________________________________ 20

Online button / relay configuration_______________________________________________________ 20

Switching of a relay via a button_________________________________________________________ 20

Switching of a relay for a limited period of time _____________________________________________ 20

Action via button _____________________________________________________________________ 21

Temperature-triggered relay switching____________________________________________________ 21

Offline button / relay configuration_______________________________________________________ 21

Starting schedule ____________________________________________________________________ 21

Button / relay settings_________________________________________________________________ 21

Heatmaster 2

Temperature comparison configuration __________________________________________________ 22

Active _____________________________________________________________________________ 22

Name _____________________________________________________________________________ 22

Sensor 1 / Sensor 2 __________________________________________________________________ 22

SPECIAL NOTE ________________________________________________________22

Note regarding emergency shutdown ____________________________________________________ 22

Standard settings in the software________________________________________________________ 22

FAQ –Frequently asked questions ______________________________________________________ 22

EXPANDABILITY_______________________________________________________22

TROUBLESHOOTING ___________________________________________________23

TECHNICAL DATA _____________________________________________________23

DISPOSAL ____________________________________________________________23

APPENDIX ____________________________________________________________24

Expansion for Internet / LAN upgrade ____________________________________________________ 24

Master software control _______________________________________________________________ 24

E-Mail notifications ___________________________________________________________________ 24

Remote servicing via Internet___________________________________________________________ 24

Expansion for analogue adaptor_________________________________________________________ 24

Battery mount ________________________________________________________________________ 24

Mounting holes for the water block (optional expansion) ____________________________________ 24

A compatible water block is the water block alphacool Keatmaster 2 cooler (Item No. 11045)_____ 24

Heatmaster 2

Introduction

Dear customer,

we congratulate you on having purchased one of the most innovative and powerful controller units currently

available on the PC water cooling market. The Alphacool Heatmaster 2 was developed in Germany over

multiple years and constantly improved. Now, after a development and testing period of almost 3 years, we

introduce this unique product. The manufacturing process is completely done in Germany, hence ensuring

the highest possible quality and excellent quality control.

We have made this operating manual as extensive as possible, but with the many possibilities the Alphacool

Heatmaster 2 offers, we cannot exclude the possibility of questions still remaining unanswered. If you have

any questions, please contact us via the manufacturer homepage at www.Alphacool.com or via E-Mail at

[email protected]om.

A multitude of expansion possibilities is implemented into the hardware. Changes in the layout cannot be

excluded. Hence it is possible that the images in the manual may differ from the product, please excuse this

in advance.

Extent of delivery

The following items are included:

1x Alphacool Heatmaster 2

4x Temperature sensors with approx. 50 cm cable

1x Internal 4-Pin USB connection cable

1x Jumper

1x Mounting material

1x Short manual

Warranty

Data, drawings, images, technical data, weight, dimensions and feature descriptions provided in brochures,

catalogues, newsletters, advertisements or price lists, have only informative character. We take no

responsibility for the correctness of this data. Regarding the type and extent of the order only the information

provided with the order and order confirmation are determining.

1. If a defect covered by the warranty occurs, you have the right to demand supplementary

performance in the extent of the provisions of the law, to withdraw from the contract or to reduce the

purchase price. The statute of limitations on the warranty claims on the delivered items is two years

from receipt of the product if you are end user consumer ((§ 13 BGB). If you are an entrepreneur (§

14 BGB), this period is reduced to one year.

2. The warrant claim is only valid in combination with the invoice, sales slip or a confirmation of your

warranty claim by ALPHCAOOL INTERNATIONAL GMBH.

3. It lies solemnly in the discretion of ALPHACOOL INTERNATIONAL GMBH to repair or replace the

defective product or components. The replaced product or component becomes property of the

ALPHACOOL INTERNATIONAL GMBH.

4. All warranty claims are handled by ALPHACOOL INTERNATIONAL GMBH or an authorized

specialized dealer. If the repair is not done by an authorized dealer or commissioned person,

ALPHACOOL INTERNATIONAL GMBH will cover neither cost nor liability, except if the repair was

coordinated with ALPHACOOL INTERNATIONAL GMBH in advance.

5. Any cost resulting from rebuilding or upgrading of the product will not be covered by ALPHACOOL

INTERNATIONAL GMBH.

6. The warranty by ALPHACOOL INTERNATIONAL GMBH does not include the following points:

I. Regular checks, maintenance or repairs or the replacement of wearing parts.

II. Operating errors or defects resulting from improper installation.

III. Damages caused by storm, water, fire overvoltage, act of nature beyond control or war improper

Heatmaster 2

connection to the mains, insufficient or improper ventilation or other reasons which cannot be

influenced by ALPHACOOL INTERNATIONAL GMBH.

IV. Damages caused by transport or improper packaging.

7. The applicable national laws in the country of the end user customer, such as claims towards the

seller, as articled in the contract, remain unaffected by this warranty agreement. ALPHACOOL

INTERNATIONAL GMBH, its branches and distributors, do not take any liability for direct or indirect

damages or losses, if no mandatory legal provisions contradict this.

8. ALPHACOOL INTERNATIONAL GMBH does not take over the warranty of the manufacturer on the

electronic components. The installation of the heatsink takes place at the customer’s own risk.

Safety notice

Please thoroughly read this safety notice to prevent possible errors which may lead to problems or damage

to your hardware.

Not suitable for children under 12 years (contains swallowable small components). Some components on the

Alphacool Heatmaster 2 may become very hot. Please be aware of the danger of burning and be extremely

cautious when touching the device.

Read this operating manual thoroughly before installation.

Before beginning working on your system please back up your data.

The Alphacool Heatmaster 2 must be installed solidly in a free space in the enclosure.

Please make sure that the USB connector is connected with the correct polarity. If the USB cable is

connected with wrong polarity, both the Mainboard as well as the Alphacool Heatmaster 2 can be damaged.

Never plug the power connector in or out whilst the PC is switched on. This can destroy the hardware of your

PC (PSU, USB connector, mainboard etc.) or even the Alphacool Heatmaster 2.

Never connect or disconnect fans, flow rate sensors, temperature sensors, relays, LEDs or other sensors or

devices whilst the system is running. This may damage the Alphacool Heatmaster 2 or even the PC

hardware.

Never interrupt a Firmware update. This may irreparably damage the controller software of the Alphacool

Heatmaster 2, resulting in the controller needing re-programming with a special programming device.

Never interrupt the software start-up of the PC software.

Do not shut down your PC suddenly by e.g. cutting the power or switching off the PSU whilst the system is

running.

Never touch the Alphacool Heatmaster 2 or one of the connected devices whilst switched on.

Intended use

The Alphacool International Gmbh cooling components are approved by Alphacool International Gmbh for

cooling of computer components. If they are used for any other purpose the warranty is voided.

System requirements

Minimum system requirements:

CPU: 500Mhz or better, recommended 1000Mhz

RAM 512 MB

50 - 100 MB HDD space

USB 1.1

Windows XP Service Pack 3, Windows Vista, Windows 7.

Heatmaster 2

Windows 98 SE, Windows 2000 Service Pack 4 with limitations.

Depending on the operation being processed the software requires some of the CPU computing power. If

you have transferred the settings to the Alphacool Heatmaster 2 and the software has been shut down, no

more CPU time is needed. The Alphacool Heatmaster 2 then runs autonomously and fulfills its purpose of

controlling and monitoring your cooling system. The Alphacool Heatmaster 2 is even network- and internet

capable with the optionally available LAN adaptor. This allows the Alphacool Heatmaster to be configured

from another PC, meaning that no software needs to be installed on the monitored system, hence not

requiring any CPU time on the system.

More information on possible expansions can be found at the manufacturer homepage www.Alphacool.com

Socket assignment

Overview

Power supply

The Alphacool Heatmaster 2 is connected to the power supply via a 4-Pin Molex plug, just like a HDD or

optical drive. Both voltage (12V and 5V) are needed, the 5V for the micro controller and 12V for the power

connectors, supplying fans and pumps. Should you intend to connect the Alphacool Heatmaster 2 to another

power source than a PC PSU (e.g. in an external enclosure or via a laboratory power supply), please note

that not only a 12V rail is needed, the 5V power rail is also required. If you intend to run the unit in stand-by

(e.g. to allow booting of the system to be triggered by the Alphacool Heatmaster 2), a 5V standby power

supply must be connected via the connection array (see overview).

Fan channels / pumps / slow sensors

Up to 6 fans can be connected to and individually controlled by the Alphacool Heatmaster 2. Additionally it is

possible to connect multiple fans to one channel via a Y-cable or similar adaptor. In such a configuration the

Heatmaster 2

fan speed signal from only one fan can be monitored, but the other fans run at the same voltage. Such a

configuration is especially useful if many fans need to be connected to a cooling array. For example, three

radiator fans can be connected to one channel. Bundling of radiator fans also comes in very handy if large

radiators such as the Mora or Phobya Nova (9 fans each). The maximum permissible number of connected

fans depends on the power consumption of the fans. Up to 18W of power may be drawn from an individual

channel passiv cooled..We propose to use an aktiv fan. The power consumption of a standard 120mm fan is

approximately 2.5 to 3.6W. Before connecting multiple fans please check the maximum power draw of the

fans. Should the 10W per channel not suffice, an active cooling system of the driver components can

increase the maximum power output up to 38W. Regarding this please consult the appendix.

The last three channels (3-Pin) are unregulated for the pumps / flow sensors, as these are controlled

separately by the software. Theoretically it is also possible to connect a fan, but the channels are unable to

detect it as such, resulting in constant 12V operation of the connected fan. The 3 channels for pumps / flow

sensors aren’t necessarily compatible with the according components. This means that in some cases it is

e.g. necessary to connect a 3-Pin plug to the pump / flow sensor. Please check in advance if the pump is

suitable for the limitations of the Alphacool Heatmaster 2 (18W per channel). On the 3 channels the 12V DC

voltage from the PSU is simply passed through, hence additional voltage adjustments are not possible. If you

wish to control the speed of your pump, this is possible with an analogue adaptor which is connected parallel

to the 6 fan channels. This allows a pump to be connected and controlled in speed e.g. according to a

measured temperature. Such analogue adaptors will be available soon. The following products can be

connected to the pump / flow sensor channels:

Pumps

EK-DCP 2,2 /4,0

Laing DDC-1T / Laing DDC-1T Plus ( requires active cooling) (as well as the RT models)

Laing DDC-1T Plus (RT-Models) (Active Air cooling needed)

Laing D4/ Laing D5 (Active cooling needed)

Alphacool TPP644 / VPP655 ((Active cooling needed)

Phobya DC12-220/260/400

Please note that the Alphacool pump adaptor may be needed for some models!

Flow rate sensors

Bach DFS 1/25io

Some Digmesa DF sensors

GMR DF Sensor including electronics

Innovatek FlowMeter

Regarding different pumps respectively the precise connection possibilities please consult our website

www.alphacool.com.

Connection array

USB

Connector for the USB cable.

Heatmaster 2

ALWAYS ensure correct connection to the pins! If incorrect connections are made or pins are

shorted out, damage may be caused to the Alphacool Heatmaster and / or the connected hardware.

Pay special attention to the correct connection of the USB cable. If the cable is connected improperly

damage may be caused to the Alphacool Heatmaster 2 or the connected hardware. Never remove the

USB connection cable when the system is switched on. The Heatmaster 2 is not hot-plug capable.

HM BUS

Heatmaster 2 BUS-utilization inquiry.

Emergency shutdown

Output for switching of a relay. Via this feature the hardware can be switched off immediately in case of an

emergency. The switching current must not exceed 100mA. Data corruption cannot be ruled out if the

emergency shutdown is activated.

PC shut down

This output can be connected to the Mainboard. When the shut-down signal is sent, the output works like the

power switch of the system.

NTC 1 -6 temperature sensors

Here the temperature sensors can be connected. Use only sensors with a resistance of 5k Ohm or 10k Oh.

The Heatmaster 2 detects these after a reset. The setting can also be made manually.

Water level

To this input an analogue coolant level sensor can be connected. With this sensor the Heatmaster is able to

give a warning if the coolant level is too low.

LED 1 silent alarm

Status LED. This connector is active when the silent alarm is activated. The switching current must not

exceed 2mA.

LED 2 alarm

Status LED. Is active when the alarm is activated. The switching current must not exceed 2mA.

LED 3 warning

Status LED. Is active when a warning is activated. The switching current must not exceed 2mA.

Relay 1-3

With the outputs relays can be controlled, the switching current must not exceed 80mA.

Button 1-3

Inputs for 3 buttons. The buttons must be equipped with a make contact to allow the Heatmaster 2 to

interpret the signal correctly.

Heatmaster reset

With the Jumper the Heatmaster can be restarted. To restart remove the jumper for a short period of time

and plug it in again.

When conducting a hardware reset it is necessary to disconnect the Heatmaster 2 in the software if

the software is started.

IMPORTANT: A reset switches off all outputs!

5V Standby

Power supply for stand-by operation. The PSU must be able to supply at least 1A of current at 5V.

12V and 5V output

Power supply for external devices.

Altri manuali per Heatmaster 2

Indice

Altri manuali Alphacool Unità di controllo

Alphacool

Alphacool Heatmaster 2 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente