Ametek Jofra ASC-400 Guida

Adjustment Manual

Advanced Signal Calibrator

ASC-400

Adjustment Manual

Advanced Signal Calibrator

JOFRA ASC-400

128897 02 2014-12-05 2

List of contents

1.0Overview....................................................................................................................................3

2.0Initiating Communication ........................................................................................................4

3.0Adjusting and calibrating the ASC-400 ..................................................................................5

4.0Test equipment.........................................................................................................................5

5.0ASC-400 Adjustment procedures ...........................................................................................6

5.1Adjusting Isolated current (mA) Input:.............................................................................................. 6

5.2Adjusting Isolated voltage Input:......................................................................................................6

5.3Adjusting current (mA) Input: ...........................................................................................................6

5.5Adjusting Voltage input: ...................................................................................................................7

5.6Adjusting Voltage Output: ................................................................................................................7

5.7Adjusting Low Resistance Output:...................................................................................................8

5.8Adjusting High Resistance Output:..................................................................................................8

5.9Adjusting Resistance input:..............................................................................................................8

5.10Adjusting Thermocouple (mV) Output:............................................................................................. 9

5.11Adjusting Thermocouple (mV) input:................................................................................................ 9

5.12Adjusting Thermocouple CJC:.........................................................................................................9

5.13Barometric reading (ASC-400-1 only):...........................................................................................10

5.14System Calibration Date: ...............................................................................................................10

5.15Barometric Pressure Calibration Date: ..........................................................................................10

6.0Exiting calibration procedures..............................................................................................11

128897 02 2014-12-05 3

1.0 Overview

The ASC-400 Advanced Signal Calibrator has a built in adjustment function for

readjustment of the calibrator. This adjustment function is based on a simple ASCII protocol,

and you can get access to that function by the USB interface.

You can use a terminal program like HyperTerminal by accessing the instrument via the USB

interface, or you can develop your own dedicated adjustment program in Visual Basic,

Labview, etc.

There is no front panel adjustment available on the ASC-400.

In this manual only the terminal mode will be described.

128897 02 2014-12-05 4

2.0 Initiating Communication

Before you can initiate the Communication needed for a readjustment, you have to install a

USB-driver. You can find the USB-driver on the memory stick which was included together

with the instrument. The driver will be located in the subfolder: utilities.

To install the driver you have to connect the instrument to your computer and then turn on

the calibrator. After a while the computer will ask for a driver and you have to locate the

driver on the USB-stick in the subfolder utilities.

When the driver is installed you will get a virtual COMPORT named AMETEK Advanced

Signal Calibrator. Start up your preferred terminal program and locate this Virtual

COMPORT in the terminal setup. Now you are ready to recalibrate the instrument.

As long as the calibrator has been within at a stable temperature within the range of 18°C

to 28°C for an hour or more, the calibrator only needs 5 minutes to warm up. If

temperature conditions were previously below 10°C or higher then 40°C, then the unit

must be allowed to stabilize for a minimum of 3 hours prior to adjustment. To initiate the

calibration mode use the terminal to send the CAL_START command. The following will be

displayed on the terminal.

Calibration is password protected Enter Password:

The password is 900. Enter the password correctly and the following will be displayed on the

terminal.

Calibration Menu

0: Exit

1: ISO Current Input (mA)

2: ISO Voltage Input (volts)

3: Current Input (mA)

4: Current Output (mA)

5: Voltage Input (volts)

6: Voltage Output (volts)

7: Low Resistance Source (ohms)

8: High Resistance Source (ohms)

9: Resistance Measure (ohms)

10: Thermocouple Output (mV)

11: Thermocouple Input (mV)

12: Thermocouple CJC

13: Barometric Pressure

14: System Calibration Date

15: Barometric Pressure Calibration Date

Enter Selection:

128897 02 2014-12-05 5

3.0 Adjusting and calibrating the ASC-400

You should recalibrate the ASC-400 at the required calibration interval (defined by the

factory as 1 year) and adjust if necessary.

Adjustment of the ASC-400 is a menu driven process. It consists of 15 different menu selec-

tions for calibration of the different functions. The only requirement being that mV must be

adjustment before CJC.

Once a particular adjustment menu selection has been made the user is prompted to either

input a signal into the ASC-400 or enter the output value of a signal from the ASC-400.

When inputting signals into the ASC-400, the readings are taken after the {enter} key is

pressed and before the next prompt. Make sure the input to the ASC-400 is stable before the

{enter} key is pressed and remains stable until the next prompt appears.

When entering the outputted value of a signal, make sure that value is stable before you enter

it; there is no backspace.

4.0 Test equipment

Recommended test equipment is listed in the table below. Equipment with similar or better

specifications can be used if the listed equipment is not available.

Equipment Manufacturer Model Quantity Purpose

Digital Multimeter Fluke 8508A 1 All functions

except CJC and

ohm measure.

Calibrator Fluke 5520A 1 All source

functions and

CJC.

Low thermal EMF

banana to banana

leads (red).

Multi Contact 28.0074-100-22 2 All functions

except mV and

CJC.

Low thermal EMF

banana to banana

leads (black).

Multi Contact 28.0074-100-21 2 All functions

except mV and

CJC.

TC – banana

cable 1 mV source and

measure.

Thermocouple

type J TC – TC

cable.

1 CJC.

Tube for

barometric

reference.

1 Barometric

reference.

For the barometric reference in ASC-400-1, a barometric reference with an accuracy of 0.125

mbar or better is required.

128897 02 2014-12-05 6

5.0 ASC-400 Adjustment procedures

5.1 Adjusting Isolated current (mA) Input:

1. Connect Calibrator mA output to Digital Multimeter mA input and to ASC-400

Isolated mA measure terminals.

2. Type “1” in the Calibration menu.

Prompt = “Input 0 mA to ASC400 - Press <enter> when stable”

3. Apply 0.000 mA (Digital Multimeter reading) to the input and press “enter”

when stable.

Prompt = “Input 24 mA to ASC400 - Press <enter> when stable”

4. Apply 24.000 mA (Digital Mulimeter reading) to the input and press “enter”

when stable. ASC-400 now returns to the Calibration menu.

5.2 Adjusting Isolated voltage Input:

1. Connect Calibrator V output to Digital Multimeter V input and to ASC-400

Isolated V measure terminals.

2. Type “2” in the Calibration menu.

Prompt = “Input 0 Volt to ASC400 - Press <enter> when stable”

3. Apply 0.000 V (Digital Multimeter reading) to the input and press “enter” when

stable.

Prompt = “Input 30 Volt to ASC400 - Press <enter> when stable”

4. Apply 30.000 V (Digital Multimeter reading) to the input and press “enter”

when stable. ASC-400 now returns to the Calibration menu.

5.3 Adjusting current (mA) Input:

1. Connect Calibrator mA output to Digital Multimeter mA input and ASC-400 mA

measure terminals.

2. Type “3” in the Calibration menu.

Prompt = “Input 0 mA to ASC400 - Press <enter> when stable”

3. Apply 0.000 mA (Digital Multimeter reading) to the input and press “enter”

when stable.

Prompt = “Input 24 mA to ASC400 - Press <enter> when stable”

4. Apply 24.000 mA (Digital Multimeter reading) to the input and press “enter”

when stable. ASC-400 now returns to the Calibration menu.

128897 02 2014-12-05 7

5.4 Adjusting current (mA) Output:

1. Connect Digital Multimeter mA input to ASC-400 mA source terminals.

2. Type “4” in the Calibration menu.

Prompt = “First calibration point. Enter mA output:”

3. Enter multimeter read value when stable (example: 0.0000) and press “enter”.

Prompt = “Second calibration point. Enter mA output:”

4. Enter multimeter read value when stable (example: 24.0000) and press “enter”.

ASC-400 now returns to the Calibration menu.

5.5 Adjusting Voltage input:

1. Connect Calibrator V output to Digital Multimeter V input and ASC-400 V

measure terminals.

2. Type “5” in the Calibration menu.

Prompt = “Input 0 volt to ASC400 - Press <enter> when stable”

3. Apply 0.000 V (Digital Multimeter reading) to the input and press “enter” when

stable.

Prompt = “Input 20 volt to ASC400 - Press <enter> when stable”

4. Apply 20.000 V (Digital Multimeter reading) to the input and press “enter”

when stable. ASC-400 now returns to the Calibration menu.

5.6 Adjusting Voltage Output:

1. Connect Digital Multimeter V input to ASC-400 V source terminals.

2. Type “6” in the Calibration menu.

3. Follow the menu prompts.

Prompt = “First calibration point. Enter V output:”

4. Enter multimeter read value when stable (example: 0.0000) and press “enter”.

Prompt = “Second calibration point. Enter V output:”

5. Enter multimeter read value when stable (example: 20.0000) and press “enter”.

ASC-400 now returns to the Calibration menu.

128897 02 2014-12-05 8

5.7 Adjusting Low Resistance Output:

1. Connect Digital Multimeter ohm input (4-wire) to ASC-400 Ohms source

terminals.

2. Set up Digital Multimeter for True ohm mode, 1 mA ( 3 mA max.) excitation

current.

3. Type “7” in the Calibration menu.

Prompt = “First calibration point. Enter ohms output:”

4. Enter multimeter read value when stable (example: 5.000) and press “enter”.

Prompt = “Second calibration point. Enter ohms output:”

5. Enter multimeter read value when stable (example: 400.000) and press “enter”.

ASC-400 now returns to the Calibration menu.

5.8 Adjusting High Resistance Output:

1. Connect Digital Multimeter ohm input (4-wire) to ASC-400 Ohms source

terminals.

2. Set up Digital Multimeter for True ohm mode, 0.1 mA (0.3 mA max.) excitation

current.

3. Type “8” in the Calibration menu.

Prompt = “First calibration point. Enter ohms output:”

4. Enter multimeter read value when stable (example: 400.00) and press “enter”.

Prompt = “Second calibration point. Enter ohms output:”

5. Enter multimeter read value when stable (example: 4000.00) and press “enter”.

ASC-400 now returns to the Calibration menu.

5.9 Adjusting Resistance input:

1. Connect Calibrator to ASC-400 Ohms measure terminals using 4-wire

connection.

2. Set up Calibrator for 4-wire connection.

3. Type “9” in the Calibration menu.

Prompt = “Input 15 ohm to ASC400 - Press <enter> when stable”

4. Apply 15.00 ohm to the input and press “enter” when stable.

Prompt = “Input 400 ohm to ASC400 - Press <enter> when stable”

5. Apply 400.00 ohm to the input and press “enter” when stable.

Prompt = “Input 4000 ohm to ASC400 - Press <enter> when stable”

6. Apply 4000.0 ohm to the input and press “enter” when stable. ASC-400 now

returns to the Calibration menu.

128897 02 2014-12-05 9

5.10 Adjusting Thermocouple (mV) Output:

1. Connect Digital Multimeter V input to ASC-400 mV source terminals (use TC to

banana cable).

2. Type “10” in the Calibration menu.

3. Follow the menu prompts.

Prompt = “First calibration point. Enter mV output:”

4. Enter multimeter read value when stable (example: -10.0000) and press

“enter”.

Prompt = “Second calibration point. Enter mV output:”

5. Enter multimeter read value when stable (example: 75.0000) and press “enter”.

ASC-400 now returns to the Calibration menu.

5.11 Adjusting Thermocouple (mV) input:

1. Connect Calibrator V output to Digital Multimeter V input and ASC-400 mV

measure terminals (use TC to banana cable).

2. Type “11” in the Calibration menu.

Prompt = “Input 0 mV to ASC400 - Press <enter> when stable”

3. Apply 0.000 mV (Digital Multimeter reading) to the input and press “enter”

when stable.

Prompt = “Input 75 mV to ASC400 - Press <enter> when stable”

4. Apply 75.000 mV (Digital Multimeter reading) to the input and press “enter”

when stable.

5.12 Adjusting Thermocouple CJC:

1. Connect Calibrator TC output to ASC-400 TC measure terminals (use

Thermocouple type J cable).

2. Type “12” in the Calibration menu.

Prompt = “Input a type J thermocouple at 0.0 degrees C - Press <enter> when

stable”

3. Apply 0°C to the input and press “enter” when stable (wait minimum 5

minutes).

Altri manuali per Jofra ASC-400

Indice

Altri manuali Ametek Apparecchiature di prova

Ametek

Ametek WT Series Manuale utente

Ametek

Ametek PCD 8 b Series Manuale utente

Ametek

Ametek NSG 4070C Manuale utente

Ametek

Ametek CSC201 Manuale utente

Ametek

Ametek MGC-LOW Manuale utente

Ametek

Ametek Newage USB Lab B.O.S.S. Manuale utente

Ametek

Ametek JOFRA HPC600 Manuale utente

Ametek

Ametek Crystal pressure 30 Series Manuale di installazione

Ametek

Ametek Jofra ASC-400 Manuale utente

Ametek

Ametek PCD 8 S Series Manuale utente

Ametek

Ametek VERSITRON BT130S Manuale utente

Ametek

Ametek Jofra MTC-650 A MKII Manuale utente

Ametek

Ametek JOFRA ASC300 Manuale utente

Ametek

Ametek Crystal Pressure HPC40 Series Manuale utente

Ametek

Ametek Land Landcal P80P Manuale utente

Ametek

Ametek Chandler Engineering 4207D Manuale utente

Ametek

Ametek OCS 500N6 Series Manuale di istruzioni

Ametek

Ametek LAND R1500T Manuale utente

Ametek

Ametek JOFRA STS-050 A/B Manuale utente

Ametek

Ametek LS1 Series Manuale utente

Ametek

Ametek Teseq NSG 3150 Manuale utente

Ametek

Ametek PK II Manuale utente

Ametek

Ametek Solartron Metrology Wigauge WHT Manuale

Ametek

Ametek Teseq NSG 3060 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente