AMS AS5047D Manuale utente
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 2/13
Table of Contents
1General Description ............................................................................................................. 3
2Hardware.............................................................................................................................. 4
2.1 Kit Content ........................................................................................................................... 4
2.2 Compatible Products............................................................................................................ 4
2.3 Pin-out.................................................................................................................................. 5
3First steps with the USB I&P Box......................................................................................... 5
4Connection from compatible Adapterboard to USB I&P Box............................................... 7
4.1 AS5047D/AS5147/AS5047P/AS5147P ............................................................................... 7
4.2 AS5050A/AS5055A.............................................................................................................. 7
4.3 AS5048A/AS5048B.............................................................................................................. 8
4.4 AS5510 ................................................................................................................................ 8
4.5 AS5600 ................................................................................................................................ 9
4.6 AS5601 ................................................................................................................................ 9
4.7 AS5247 .............................................................................................................................. 10
5Software............................................................................................................................. 11
5.1 GUI Overview..................................................................................................................... 11
5.2 Firmware Update................................................................................................................12
6Ordering Information.......................................................................................................... 12
Copyright ........................................................................................................................................... 13
Disclaimer..........................................................................................................................................13
Revision History
Revision
Date
Owner
Description
1.0
21.01.2014
AZEN
Initial revision
1.1
06.08.2014
RPH
Minor changes
1.2
06.10.2014
AZEN
Updated Compatible Products
1.3
12.12.2014
AZEN
Add Section 4
1.4
09.09.2015
AZEN
Add AS5047P/AS5147P/AS5247
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 3/13
1 General Description
This Manual explains how to use the USB I&P Box.
The USB I&P Box is a Programming-Tool for Magnetic Position Sensors with I2C or SPI Interface.
After connecting a Magnetic Position Sensor to I&P Box you can open the GUI on your computer
and start programming.
For programming a Magnetic Position Sensor the sensor should be mounted on a PCB to get
connected with all the necessary pins of the sensor.
For Position Sensors, ams provides Adapterboards where an easy access from the Sensor to the
USB I&P Box is possible (not in the Tool-Kit included)
Figure 1:
USB I&P Box
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 4/13
2 Hardware
2.1 Kit Content
Table 1:
USB I&P Box Kit content
Part
Description
Picture
USB
I&P Box
USB Interface & Programming Box
USB
cable
To connect the USB I&P box to a computer
10-way
cable
To connect the USB I&P Box to a compatible sensor
on an existing board
Quick
Start
Guide
First steps introduction
USB
flash
drive
Contains the USB I&P Box Software and manuals.
To get latest SW / FW and Manuals please refer to
http://ams.com/eng/Support/Demoboards/Accessories
/Evaluation-Tool/USB-I-P-Box
2.2 Compatible Products
Table 2:
Compatible Products
Product
Description
Adapterboard available
AS5047D
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5047P
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5048A
14-bit Angular Position Sensor with SPI Interface
yes
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 5/13
Product
Description
Adapterboard available
AS5048B
14-bit Angular Position Sensor with I2C Interface
yes
AS5050A
Low Power 10-Bit Magnetic Position Sensor
yes
AS5055A
Low Power 12-Bit Magnetic Position Sensor
yes
AS5147
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5147P
14-bit On-Axis Magnetic Rotary Position Sensor
yes
AS5247
14-bit Dual-Die Magnetic Rotary Position Sensor
yes
AS5510
Linear Hall Sensor with I²C Output
yes
AS5600
12-bit Programmable Contactless Potentiometer
yes
AS5601
12-bit Programmable Contactless Encoder
yes
2.3 Pin-out
The pin-out of the USB I&P box is shown below in Table 3
Table 3:
USB I&P Box Pin-out and wire description
Note: The interface voltage of the USB I&P Box is 3,3V. Use the 3,3V mode when connecting to a
position sensor board.
3 First steps with the USB I&P Box
The first steps to get started with the USB I&P Box are described below in Figure 2.
Pin #
Color
Definition
SPI Mode
1
Brown
5V Supply
Not used
2
Red
3.3V Supply
Positive power supply
3
Orange
SPI-CS(0)
SPI-CS(0)
4
Yellow
I2C-SCL
Not used
5
Green
SPI-CLK
SPI-CLK
6
Blue
I2C-SDA
Not used
7
Purple
SPI-MOSI
SPI-MOSI
8
Grey
SPI-CS(1)
Optional (dual die version)
9
White
SPI-MISO
SPI-MISO
10
Black
GND
GND
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 6/13
Figure 2:
First steps with the USB I&P Box
Getting started with your programmer
Ready to start
Install the USB I&P Software on your
computer
Connect the right wires of the USB I&P
Connector cable to your magnetic position
sensor
Connect your USB I&P Box to your
computer via USB cable
Open the USB I&P Software
Choose the right Device
For using the right wires
please refer to Table 3
USB I&P Box
User Manual
www.ams.com Revision 1.4 / 09/09/2015 page 7/13
4 Connection from compatible Adapterboard to USB I&P Box
4.1 AS5047D/AS5147/AS5047P/AS5147P
Figure 3:
How to connect an AS5047D/AS5147/AS5047P/AS5147P adapterboard to the USB I&P Box
4.2 AS5050A/AS5055A
Figure 4:
How to connect an AS5050A/AS5055A adapterboard to the USB I&P Box
Questo manuale è adatto per i seguenti modelli
11
Indice
Altri manuali AMS Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
