Antari AF-4 Manuale utente
1
AF-4 / AF-4R
Special Effects Fan
User Manual
English - Français - Deutsch
© 2017 Antari Lighting and Effects Ltd.
2
3
User Manual
Safety Information
Please read the following safety information carefully before operating the
machine. This information includes important safeguards about installation,
usage, and maintenance. Pay attention to all warning labels and instructions in
this manual and printed on the machine.
If you have questions about how to operate the machine safely, please contact your local
Antari dealer for help.
․Keep this device dry.
․Always connect to a grounded circuit to avoid risk of electrocution.
․Before connecting machine to power, always check voltage indicate on machine match
to your local AC voltage. Do not use the machine if AC power voltage does not match.
․Disconnect the machine from AC power before servicing and when not in use.
․This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled
onto electronic parts, immediately unplug the machine and contact your local Antari
dealer for advice.
․No user serviceable and modifiable parts inside. Never try to repair this product, an
unauthorized technician may cause damage or malfunction to the machine.
․For adult use only. Never leave the machine running unattended.
․Installed the machine in a well-ventilated area. Provide at least 50 cm space around
the machine.
․Make sure there are no flammable materials close to the machine while operating.
․If the machine fails to work, unplug the machine and stop operation immediately.
Contact your local Antari dealer for advise.
4
Unpacking and Inspection
Immediately upon receiving the machine, carefully unpack the carton, check the content to
ensure that all parts are present and have been received in good condition. If any parts
appear damaged or mishandled from shipping, notify the shipper immediately and retain the
packing material for inspection.
What is included: 1 x AF-4 / AF-4R Special Effect Fan
1 x User Manual
Product Dimensions
5
Product Overview
Setting Up
Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm
open space around the machine.
Step 2: Connect the machine to suitable rated power supply. To determine the power
requirement for the machine refer to the label on the machine.
Always connect the machine to a protected circuit and ensure it is properly
grounded to avoid risk of electrocution.
LCD display Control Panel
XLR 5-Pin DMX Connector
Wire Remote Socket
Wireless Operation
(For AF-4R Only)
Air Inlet
Air Outlet
6
Step 3: Turn on the machine and LCD display will show “Ready”. Now the machine is ready
for operation.
Step 4: To start making wind, locate the Volume button on the control panel, and press the
button to start making wind.
Step 5: To turn off the machine, press the Stop button and unplug the power cord.
Operation
Control Panel Operation
The machine can be operated with the onboard digital control interface.
Button
Function
[MENU]
Scroll through setting menu
▲ [UP]/[TIMER]
Up/Activate Timer function
▼[DOWN]/[VOLUME]
Down/Activate Volume function
[STOP]
Deactivate Timer/Volume function
Control Menu
Set interval from 1 to 180 seconds
Interval
Set 180s
7
Set duration from 1 to 120 seconds
Set timer output from 20 to 100%
Set output volume from 20 to 100%
Set DMX address from 1 to 512
Turn On or Off wireless control
Turn On/Off run last setting function
W-2 Wireless Operation (For AF-4R Only)
The wireless remote control system W-2 consists of a transmitter equipped with four buttons
to turn wind output on or off, and adjust the output volume; with an onboard receiver attached
to the rear panel of the AF-4R.
W-2 Wireless Transmitter
Duration
Set 120s
Timer
Out 100%
Volume
Out 100%
DMX512
Add. 512
Wireless
OFF
Quick
Start OFF
8
Wireless Receiver
Wireless remote control function:
[A] button – Turn on wind output
[B] button – Turn off wind output
[C] button – Increase output volume
[D] button – decrease output volume
In a free open space the effective distance is 50 meters, actual usage depends on obstacle
level; the effective distance is 10-25 meters.
Registering a transmitter
Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 10
transmitters. Follow below steps to pair or delete a transmitter from a receiver.
Step 1: Power off the AF-4R
Step 2: Press and hold [DOWN] button
Step 3: Turn power on and hold [DOWN] button until below menu shows on display
Step 4A: Press [UP] to pair a new transmitter; press any button on the W-2 remote to finish
pairing.
Step 4B: Press [DOWN] button to delete existing transmitter.
UP: Pair
DOWN:Del
9
Transmitter battery replacement
If the effective distance seems to decrease, it is possible the battery level is low and
requires replacement. In order to replace the battery, undo the three screws on the back of
transmitter to release the cover. Replace with same type and specification of battery which
is 27A 12V
Z-3 Remote Control Operation (Optional)
To operate the machine by remote control, connect the remote to the microphone jack
located on the rear of machine. Use the switch to turn wind on/off, and use the rotary knob
to adjust the output volume from 0~100%.
Z-3 Remote (Optional)
DMX Connector Pin Assignment
The machine provides 5-pin XLR connector for DMX connection. The diagram below
indicates pin assignment information.
Pin
Function
1
Ground
2
Data-
3
Data+
10
DMX Operation
Making the DMX Connection – Connect the machine to a DMX controller or to one of the
machines in the DMX chain. The machine uses 5-pin XLR connector for DMX connection.
DMX Channel Function
Channel Mode
Channel
Value
Function
1
1
0-5
Off
6-255
Fan 20-100%
Service and Maintenance
․Do not allow the machine to become contaminated.
․Remove dust from air vents with air compressor, vacuum or a soft brush.
․Excessive dust, liquid and dirt built up will degrade performance and cause
overheating.
Fuse Replacement
Disconnect AC power before replacing fuse. Only replace fuse with same type
and rating.
Step 1: Disconnect power cord from supply.
Step 2: Use a flat-head screwdriver to release fuse holder.
Step 3: Replace fuse with exact same type and rating as indicated below.
Step 4: Reinsert fuse holder.
Fuse
120V = T1.6A 250V
240V = T0.8A 250V
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Antari Fan
