AQUATROL AQT-MSV-1 Guida rapida

AQTMSV1

OPERATIONAL MANUAL

WWW.AQUATROLTECH.COM

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

SPECIFICATIONS

DIAGRAM

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

OPERATION

Simple turn the wheel into the desire position. The following table explains each

position of the regeneration process.

#PROCESS DESCRIPTION RECOMMENDED TIME

SERVICE

Raw water enters the valve and flows

through the resin (down-flow). This

softened water flows from the bottom

through the riser pipe (upflow) to the

valve body and finally exit through outlet

valve.

Until hardness grows

above 0 or after

calculated time of

services finishes.

BACKWASH

Raw water enters the valve and flows

through the riser pipe, expanding the

resin bed and backwashing all impurities.

Backwashing water flows out from drain.

10 minutes.

3.1

BRINE DRAW

Raw water enters into the valve through

the injector, producing a Venturi effect,

which sucks the brine from the brine

tank. Brine flows through the resin

(down-flow), through bottom strainer,

upward along the riser pipe and finally

out the valve from drain.

40 minutes.

3.2

SLOW RINSE

After brine is finished, raw water

enters the valve and flows in the same

direction as in the Backwash process.

Raw water rinses all the residual salt

from the valve, injector and resin (keeps

same position of BRINE position).

10-15 minutes.

BRINE TANK REFILL

Raw water enters into the valve and

flows through the injector outlet to the

brine tank. Brine tank is refilled. Another

part of the water flows out from drain.

Until water reaches

calculated level. Do

not forget to add salt

into the brine tank

before Brine Refill.

FAST RINSE

Raw water enters the valve and flows

through the resin (down-flow), then

upward the riser pipe to the valve body

and finally exit through drain valve.

5 minutes.

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

OPERATION

1. SERVICE

2. BACKWASH

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

OPERATION

3.1 BRINE DRAW

3.2 SLOW RINSE (same position as brine draw after brine is nished)

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

OPERATION

4. BRINE TANK REFILL

5. FAST RINSE

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

CONTROL VALVES

TROUBLESHOOTING

PROBLEM CAUSE CORRECTION

SOFTENER WATER

OUTPUTS

1. By pass opened

2. No salt in brine tank

3. Injector blocked

4. No enough water

refilled to brine tank

5. Leak in riser pipe

6. Leak inside the body valve

1. Close bypass

2. Male sure is enough salt in brine tank

3. Change or clean injector

4. Increase refill time

5. Check riser pipe and change it

if necessary

6. Repair body valve or change valve

CAN NOT SUCK SALT

1. Inlet pressure too low

(at least 30 psi)

2. Brine hose blocked

3. Leak in brine hose

4. Injector damaged

5. Leak inside the body valve

1. Increase inlet pressure

(min 30 psi)

2. Check and clean brine hose

3. Check and change brine hose

4. Change injector

5. Repair body valve or change valve

EXCESS WATER IN

BRINE TANK

1. Brine refill time too long

2. Excess water in brine tank

after brine draw

1. Adjust refill time

2. Check if injector is plugged

WATER FLOWS

OUT FORM DRAIN

CONTINUALLY

1. Leak inside the body

1. Change valve

TANK

OR VALVE LEAKS

1. Excess pressure in pipeline

2. Pipeline blocked or plugged

1. Readjust pressure to the

recommended operating pressure

2. Check pipelines and change

if necessary

WWW.AQUATROLTECH.COM

Distributed by:

CONTROL VALVES

AQUATROL |P.O. Box 2235 Chino Hills, CA 91709 •USA

AQT-MSV-1 Specications:

Temp Range: 41º F (5º C) – 113ºF (45º C)

Maximum Temperature: 122ºF

Pressure Range: 21.8 psi - 87 psi

Control Type: Manual

Electricity: None Required

Base: 2.5”

Inlet: 1”

Outlet: 1”

Drain: 1”

Riser Pipe: 1.05” OD

Water Capacity Service: 17.02 gpm @ 21.8 psi

Water Capacity Back Wash: 6.7 gpm @ 21.8 psi

Tank Diameters: 6” – 12”

Material of Construction:

Body: Noryl

Handle: Metal

Internal Disc: Ceramic

INJECTORS FOR AQT-MSV-1

Use the following table to choose the correct

injector depending on the tank size.

TANK SIZE VALVE INJECTOR

7” -12” AQT-MSV-1

BLACK

13” -14” AQT-MSV-1

RED

16” AQT-MSV-1

GREEN

Indice

Altri manuali AQUATROL Unità di controllo

AQUATROL

AQUATROL 88 Manuale

AQUATROL

AQUATROL POWERFLO Series Manuale utente

AQUATROL

AQUATROL POWERFLO Series Manuale del proprietario

AQUATROL

AQUATROL 69 Manuale

AQUATROL

AQUATROL AQT-275 Manuale utente

AQUATROL

AQUATROL POWERFLO AQT-315 Manuale utente

AQUATROL

AQUATROL POWERFLO AQT-285 Manuale utente

AQUATROL

AQUATROL AQT-56ST Manuale utente

AQUATROL

AQUATROL POWERFLO AQT-290 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente