Arecont Vision AV818X Manuale utente

AV818X/AV836X Installation Manual

1. Prepare mounting area as shown on Pic. 1.

Note, you need either #10-32 threaded inserts or you can use thru holes in desired surface

and #10 washers and #10-32 nuts (not included)

2. Remove two #4-40 screws on the top of the camera.

3. Remove retaining ring and plastic dome. There are four #10 countersunk holes in front camera

base.

4. Using enclosed four #10-32 FH Phillips screws attach camera to the desired surface.

5. Place plastic dome into retaining ring so the flange of the dome rests inside of retaining ring.

6. Carefully rotate dome inside of the ring until holes in ring and dome will match

7. Place retaining ring and dome onto front camera base, matching holes in ring and dome with

two #4 threaded holes in base.

8. Secure retaining ring and dome to front camera base, using screws from step 2,

PIC.1

BACK COVER WITH MOUNTING DIMENSIONS

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

AV818X/AV836X Tilt Adjustment Instruction A

AV8180 is supplied with 3 shaft holders stocked up on each side (further referred to as

“floors”) Camera is installed on the 2nd floor as a default.

If you use camera in installation such way so the center plane of the Main Bracket with 4

lenses is perpendicular to the mounting surface, you need to move camera to the 1st floor

to fit camera in dome. (Instruction A)

If you use camera in installation such way so the center plane of the Main Bracket with 4

lenses is parallel to the mounting surface you need to move camera to the 3rd floor.

(Instruction B)

PIC. 2

INSTRUCTION A:

1. Use enclosed 1/16” hex L-key to undo set screws on the top of the “second

floor” shaft holders, while holding the bracket. Don’t completely remove set

screws from holders. Carefully place bracket on its side.

2. Using enclosed 5/64” hex L-key remove 4 screws from shaft holders.

3. Remove “1st floor” and “3rd floor” shaft holders from both sides. Place shaft

holders with set screws onto the main plate.

4. Using screws from step 2 attach both holders to main plate. (see Pic. 2 for

positioning)

5. Secure bracket axis with set screws, using 1/16” hex L-key.

6. Cut the excess of fabric with the blade or scissors if necessary.

7. Do not discard holders as they may be used in future installation modifications.

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

AV818X/AV836X Tilt Adjustment Instruction B

INSTRUCTION B:

1. Make sure that bracket lies on the same side as an open threaded hole next to

shaft holders. This is your “standard” installed position (see Pic. 3, holes

circled)

2. Remove top fabric sheet.

A. Using 1/16” hex L-key undo 5 screws on the top of the bracket to release

upper end of the fabric. Set small bracket aside

B. Remove 2 screws to release middle section of the fabric.

C. Remove 5 screws from the bottom arc, set arc aside and remove fabric sheet.

3. Note the position of shaft holders on the main plate in relationship to open

threaded hole next to shaft holders.

4. Using enclosed 1/16” hex L-key undo set screws on the top of the “second

floor” shaft holders, but don’t completely remove set screws from holders.

5. Using enclosed 5/64” hex L-key remove 4 screws from shaft holders.

6. Switch shaft holders so the ones with set screws will be on the top (3rd floor)

Make sure that:

A. Shaft holders are on the same positions as they were before modification

(see Pic. 2)

B. Shaft holders with set screws are the “top floor”

7. Install Bracket on the “3rd floor”.

8. Using 4 #6-32 1.5”LG. screws from step 5 attach both structures to main

plate.

9. Secure bracket axis with set screws, using 1/16” hex L-key.

10. Install enclosed fabric sheet. Note that fabric sheet is smooth on one side and

rough on another. Rough side is conductive and should face out. Smooth

(isolated) side is facing PCBs. If you have any doubts, use conventional tester:

rough surface shows no electrical resistance.

A. Line up upper edge of the fabric with upper edge of the bracket. Place small

bracket from 2A on the top of the fabric. Using 1/16” hex L-key install 5

screws from step 2A.

B. Line up bottom edge of the fabric with outer edge of the bottom arc from

step 2C and using 1/16” hex L-key install 5 screws from step 2C.

C. Install 2 screws from step 2B

11. Cut the excess of fabric with the blade or scissors.

12.

www.arecontvision.com avsales@arecontvision.com 818.937.0700 877.CAMERA.8

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Arecont Vision Telecamera IP

Arecont Vision

Arecont Vision MegaVideo AV2105 Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV2100-AI Manuale utente

Arecont Vision

Arecont Vision AV12186DN SurroundVideo Manuale utente

Arecont Vision

Arecont Vision AV10005DN Manuale utente

Arecont Vision

Arecont Vision AV5100M Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV1300 Manuale utente

Arecont Vision

Arecont Vision MegaDome AV2155 Manuale utente

Arecont Vision

Arecont Vision Surround Video AV8360 Manuale utente

Arecont Vision

Arecont Vision MegaDome AV3155 Manuale utente

Arecont Vision

Arecont Vision MegaDome AV1355 Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV3130 Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV5100-AI Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV3100-AI Manuale utente

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manuale utente

Arecont Vision

Arecont Vision AV3236DN Manuale utente

Arecont Vision

Arecont Vision AV3110 Manuale utente

Arecont Vision

Arecont Vision AV10005 Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV3105 Manuale utente

Arecont Vision

Arecont Vision MegaDome 2 AV1255AM Manuale utente

Arecont Vision

Arecont Vision MegaDome AV5155 Manuale utente

Arecont Vision

Arecont Vision AV12186DN SurroundVideo Manuale utente

Arecont Vision

Arecont Vision Surround Video AV8185 Manuale utente

Arecont Vision

Arecont Vision MegaVideo AV5110 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente

Digitus

Digitus DN-16085-1 Manuale utente