ARGON18 MY2016 Nitrogen Pro Manuale utente

NITROGEN PRO: ASSEMBLY GUIDE

Valid for MY2016 Nitrogen Pro

Revision 7.0 - 04-01-2016

1. Frame Inspection . . . . . . . . . . . . . . . . . . . . . ...................2

2. Frameset Parts . . . . . . . . . . . . . . . . . . . . . ......................3

3. Headset Installation . . . . . . . . . . . . . . . . . . . . ..................5

4. Stem/Handlebar Installation . . . . . . . . . . . . . . . . . . . . ..........8

5. Front Brake Installation. . . . . . . . . . . . . . . . . . . . . . . . . . ........16

6. Rear Brake Installation . . . . . . . . . . . . . . . . . . . . . . ............20

7. Cable Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . .....22

8. Electronic Drive-train Specication . . . . . . . . . . . . . . . . . .. . . .28

9. Seatpost Installation. . . . . . . . . . . . . . . . . . . . . . . . . ...........32

10. Saddle Adjustment . . . . . . . . . . . . . . . . . . . . . . . .............33

11. Derailleur Hanger Adjustment. . . . . . . . . . . . . . . . . . . . . . . . ..34

12. Frameset Parts Checklist . . . . . . . . . . . . . . . . . . . . . . . ........36

For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,

particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque

wrench to make sure every bolt is at the right torque setting to prevent damage.

NITROGEN PRO: Table of Contents

My Nitrogen Pro

Date of purchase:

Retailler:

Size:

Serial Number:

Parts installed on the frame Description Screw Tork Detail

type Nm

1 Front derailleur hanger Screw (2) 3mm 4Nm Loctite

2 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite

3 Bottle cage Screw (4) 4mm 3Nm Grease

4 Bottom bracket cable guide Screw 5mm 1.5Nm Grease

IMPORTANT:

The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their torque

speciﬁcations.

NITROGEN PRO: 1. Frame Inspection

BEFORE ASSEMBLING YOUR NEW NITROGEN PRO, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:

1. Brakes and gears cables and housing set

2: Frameset parts checklist (see p.36)

3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)

4: For reference, check serial number and write it on p.1

5: All the necessary bolts (refer to Frameset Parts, p.3)

6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is

straight (p.35)

NITROGEN PRO: 2. Frameset Parts

Images are for reference only. Proportions are not accurate.

Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.

17 18

15 4 514 13

109

67128

17b

17f

17a

17g

17d

17e

17c

17h

17i

17h

17i

17h 18b

18f

18a

18g

18d

18e

18c

18h

18i

18h

18i

18h

Brake & derailleur

cable / housing kit

JB527AR01, JD527AR01

NITROGEN PRO: 2. Frameset Parts

AHB5000 (38cm, 40cm, 42cm, or 44cm)

Spacer

20mm

Stem A.03

Large

Stem A.02

Medium

Stem A.01

Small

Elastic Cover

Large

Elastic Cover

Small

Washer

Screw

M8x50mm

Screw

M8x30mm

Screws

M5x16mm

23 24 25 26 27 28 29 30 31 32

Frameset Handlebar Width

Stem Size 20mm

Size 38 40 42 44 Small Medium Large Spacer

X-Small

Small

Medium

Large

X-Large

Notes: 38cm Handlebar is only available aftermarket.

If you wish to purchase the third non-included stem, you can do so by ordering it as a spare part

Install the 3D headset (16) according to

the AERO Presst assembly guide. You can

choose from 3 dierent heights: 25mm,

15mm or 0mm.

NITROGEN PRO: 3. Headset Installation

GREASE

NITROGEN PRO: 3. Headset Installation

25mm

15mm

0mm

setup

5 5

Compressor

Top cap (including O-ring & seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

head tube

(bike)

head tube

(bike)

head tube

(bike)

To remove the 3D bearing holder, insert the Park Tool

RT-1 and then tap it carefully until the spacer comes out.

STEP

Inspect the bike’s head tube for any sharp edges and

apply a small amount of grease.

STEP

For the 25mm and 15mm setups, lightly grease the

bottom section of the 3D bearing holder (6) and insert

the plastic sleeve (7).

STEP

Position the headset inside the head tube. Place

the top 3D assembly with the headset bearing inside

(this will prevent the sleeve from getting damaged).

Add the compression ring on top of the bearing, then

add the press t 3D system tool and softly press down

the assembly until it bottoms out using a Bearing Cup

Press (Park Tool HHP-2). Then, insert the bottom

bearing (5), compression ring (4) micro spacers (3) and

top cap (2), slide the fork and stem and measure the

steerer length needed.

For the 0mm setup , do not use the plastic sleeve.

Install the 3D bearing holder (6) with grease applied

directly inside the frame.

STEP

First, you must assess which setup suits your needs:

25mm, 15mm or 0mm.

NITROGEN PRO: 3. Headset Installation

Compressor

Top cap (including O-ring and seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

Press Fit 3D system tool 1 1/4”

Bearing Cup Press (Park Tool HHP-2)

IMPORTANT: Use the Press Fit 3D system tool 1 1/2” with

the Bearing Cup Press (ParkTool HHP-2) to avoid any

damage on the bike frame.

NITROGEN PRO: 4. Stem/Handlebar Installation

Handlebar Width (cm)

Stems size (stems included)

S M L 20mm spacer

CONFIGURATION MATRIX

If you wish to purchase

the third non-included

stem, you can do so by

ordering it as a spare

part.

Failure to use long

screw when assembling

bar with +20mm spacer

of any conguration can

lead to serious injury

NITROGEN PRO: 4. Stem/Handlebar Installation

1. Choose the desired stem length, bolt, and spacer

needed (refer to the Product Matrix chart on p.X) – note

that the bolt comes pre-coated with Loctite. In the event

of assembling and disassembling, one drop of blue

Loctite (#242 or #243) must be applied on the bolt

threads.

Altri manuali per MY2016 Nitrogen Pro

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ARGON18 Bicicletta

ARGON18

ARGON18 E-118 NEXT Manuale utente

ARGON18

ARGON18 E-119 TRI+ Manuale utente

ARGON18

ARGON18 E-119 TRI+ Manuale utente

ARGON18

ARGON18 GALLIUM CS 281A Manuale utente

ARGON18

ARGON18 GALLIUM PRO DISC 338A 2021 Manuale utente

ARGON18

ARGON18 E-116 Manuale utente

ARGON18

ARGON18 GALLIUM PRO 259A Manuale utente

ARGON18

ARGON18 KRYPTON PRO Manuale utente

ARGON18

ARGON18 KRYPTON PRO 302A Manuale utente

ARGON18

ARGON18 E-117 TRI+ Manuale utente

ARGON18

ARGON18 E-119 TRI Manuale utente

ARGON18

ARGON18 SUM PRO 2022 Manuale utente

ARGON18

ARGON18 ELECTRON PRO Manuale utente

ARGON18

ARGON18 E-119 TRI Manuale utente

ARGON18

ARGON18 E-117 TRI Disc 317A Manuale utente

ARGON18

ARGON18 GALLIUM DISC 280A Manuale utente

ARGON18

ARGON18 Road Race Manuale utente

ARGON18

ARGON18 E-118 NEXT Manuale utente

ARGON18

ARGON18 E-Road Manuale utente

ARGON18

ARGON18 E-119 TRI+ Manuale utente

ARGON18

ARGON18 E-118 NEXT Manuale utente

ARGON18

ARGON18 KRYPTON Manuale utente

ARGON18

ARGON18 KRYPTON PRO 333A Manuale utente

ARGON18

ARGON18 nitrogen Manuale utente

Manuali Bicicletta popolari di altre marche

RAMBO

RAMBO R1000X2M-FF-BFD Manuale utente

Vermeiren

Vermeiren SAFARI Manuale utente

Velec

Velec A2/36V Manuale utente

Coswheel

Coswheel A-ONE Manuale utente

Betzold

Betzold 97869 Manuale utente

Cervélo

Cervélo S3 2019 Manuale utente

Tenways

Tenways AGO X Manuale utente

Festo

Festo EGSC-BS-KF Manuale elenco delle parti

Gio Electric

Gio Electric H1 Volt Manuale utente

GOGOBEST

GOGOBEST GM30 Manuale utente

DAHON

DAHON CIAO - 2009 Manuale utente

Aprimatic

Aprimatic ONDA 500 Guida rapida

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manuale di istruzioni

Greyp

Greyp G6 Series Manuale utente

Babboe

Babboe Carve-E Manuale utente

Huka

Huka orthros Manuale utente

Xtracycle

Xtracycle Stoker 2021 Manuale utente

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manuale utente