ARGON18 NITROGEN PRO 230A Manuale utente
NITROGEN PRO 230A: ASSEMBLY GUIDE
Valid for MY2017-MY2018 Nitrogen Pro 230A
Revision 12.1 - 28-01-2019
1. Frame Inspection ........................................2
2. Frameset Parts ...........................................3
3. Headset Installation......................................5
4. Stem/Handlebar Installation..............................8
5. Front Brake Installation..................................16
6. Rear Brake Installation ..................................20
7. Cable Housing Installation ..............................22
8. Electronic Drive-train Specication ......................28
9. Seatpost Installation ....................................32
10. Saddle Adjustment ....................................33
11. Derailleur Hanger Adjustment..........................34
12. Parts’ SKUs and Descriptions ...........................36
13. Appendix..............................................38
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
NITROGEN PRO 230A: Table of Contents
1
My Nitrogen Pro
Date of purchase:
Retailler:
Size:
Serial Number:
Parts installed on the frame Description Screw Tork Detail
type Nm
1 Front derailleur hanger Screw (2) 3mm 4Nm Loctite
2 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite
3 Bottle cage Screw (4) 4mm 3Nm Grease
4 Bottom bracket cable guide Screw 5mm 1.5Nm Grease
IMPORTANT:
The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their torque
specications.
NITROGEN PRO 230A: 1. Frame Inspection
2
BEFORE ASSEMBLING YOUR NEW NITROGEN PRO, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:
1. Brakes and gears cables and housing set
2: Frameset parts checklist (see p.36)
3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)
4: For reference, check serial number and write it on p.1
5: All the necessary bolts (refer to Frameset Parts, p.3)
6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is
straight (p.35)
IMPORTANT: No more than 30mm of spacer can be place between the stem and the top cap of the 3D system.
And the use of more than 5mm spacer on top of the stem could void the eciency of the compressor.
These practices will automatically cancel any warranty claim against the manufacturer.
NITROGEN PRO 230A: 2. Frameset Parts
3
38757
38885 38260
38884
38883 38882
38724
8065480655
38880 38878 38888
FK.NITPRO.230A
SP.NITPRO.230A
38881 38879 39009
80375,
80478
80374,
80477
8042480425
running change
Images are for reference only. Proportions are not accurate.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
*For more info please consult notice on Seatpost clamp dated 2016-06-09
80871 80870
38881
80554
80825
NITROGEN PRO 230A: 2. Frameset Parts
Spacer
20mm
Stem A.03
Large
Stem A.02
Medium
Stem A.01
Small
Elastic Cover
Large
Elastic Cover
Small
Washer
M8
Screw
M8x50mm
Screw
M8x30mm
Screws
M5x16mm
4
Frameset Handlebar Width
Stem Size 20mm
Size 38 40 42 44 Small Medium Large Spacer
X-Small
Small
Medium
Large
X-Large
Notes: 38cm Handlebar is only available aftermarket.
If you wish to purchase the third non-included stem, you can do so by ordering it as a spare part
80034 80030 80029 80162 80163 80104 80028 80105 80106 80107
AHB5000 - 38cm - 80073
AHB5000 - 40cm - 80074
AHB5000 - 42cm - 80075
AHB5000 - 44cm - 80076
Install the 3D headset (16.3 & 16.4)
according to the AERO Presst assembly
guide. You can choose from 3 dierent
heights: 25mm, 15mm or 0mm.
5
NITROGEN PRO 230A: 3. Headset Installation
16.3 & 16.4
GREASE
GREASE
GREASE
GREASE
6
NITROGEN PRO 230A: 3. Headset Installation
25mm
15mm
0mm
setup
setup
setup
5
3
4
1
1
1
5
3
4
5
3
4
5
6
7
2
6
2
7
8
6
5 5
Compressor
Top cap (including O-ring & seal)
Micro spacers
Compression ring
Bearing
3D bearing holder
Plastic sleeve (no need for 0mm setup)
Top cap for 0mm setup
1
2
3
4
5
6
7
8
head tube
(bike)
head tube
(bike)
head tube
(bike)
To remove the 3D bearing holder, insert the Park Tool
RT-1 and then tap it carefully until the spacer comes out.
1
STEP
Inspect the bike’s head tube for any sharp edges and
apply a small amount of grease.
2
STEP
For the 25mm and 15mm setups, lightly grease the
bottom section of the 3D bearing holder (6) and insert
the plastic sleeve (7).
3
STEP
Position the headset inside the head tube. Place
the top 3D assembly with the headset bearing inside
(this will prevent the sleeve from getting damaged).
Add the compression ring on top of the bearing, then
add the press t 3D system tool and softly press down
the assembly until it bottoms out using a Bearing Cup
Press (Park Tool HHP-2). Then, insert the bottom
bearing (5), compression ring (4) micro spacers (3) and
top cap (2), slide the fork and stem and measure the
steerer length needed.
For the 0mm setup , do not use the plastic sleeve.
Install the 3D bearing holder (6) with grease applied
directly inside the frame.
4
STEP
First, you must assess which setup suits your needs:
25mm, 15mm or 0mm.
7
NITROGEN PRO 230A: 3. Headset Installation
Compressor
Top cap (including O-ring and seal)
Micro spacers
Compression ring
Bearing
3D bearing holder
Plastic sleeve (no need for 0mm setup)
Top cap for 0mm setup
1
2
3
4
4
5
5
6
6
7
7
8
Press Fit 3D system tool 1 1/4”
Bearing Cup Press (Park Tool HHP-2)
IMPORTANT: Use the Press Fit 3D system tool 1 1/2” with
the Bearing Cup Press (ParkTool HHP-2) to avoid any
damage on the bike frame.
8
NITROGEN PRO 230A: 4. Stem/Handlebar Installation
Handlebar Width (cm)
Stems size (stems included)
38
40
42
44
S M L
70mm 80mm *(110mm)
80mm 90mm *(100mm)
*(80mm) 90mm 100mm
*(90mm)
*Requires the purchase of an additional stem from the ones included in basic assembly.
100mm 110mm
20mm spacer
CONFIGURATION MATRIX
CONFIGURATION MATRIX
If you wish to purchase
the third non-included
stem, you can do so by
ordering it as a spare
part.
Failure to use long
screw when assembling
bar with +20mm spacer
of any conguration can
lead to serious injury
9
NITROGEN PRO 230A: 4. Stem/Handlebar Installation
1. Choose the desired stem length, bolt, and spacer
needed (refer to the Product Matrix chart on p.X) – note
that the bolt comes pre-coated with Loctite. In the event
of assembling and disassembling, one drop of blue
Loctite (#242 or #243) must be applied on the bolt
threads.
Indice
Altri manuali ARGON18 Bicicletta
ARGON18
ARGON18 SUBITO Manuale utente
ARGON18
ARGON18 NITROGEN 231A Manuale utente
ARGON18
ARGON18 Grey Matter Manuale utente
ARGON18
ARGON18 GALLIUM 279A Manuale utente
ARGON18
ARGON18 KRYPTON 212A Manuale utente
ARGON18
ARGON18 MY2016 Nitrogen Pro Manuale utente
ARGON18
ARGON18 RADON Manuale utente
ARGON18
ARGON18 nitrogen Manuale utente
ARGON18
ARGON18 ELECTRON PRO 245A Manuale utente
ARGON18
ARGON18 E-118 NEXT Manuale utente
ARGON18
ARGON18 E-80 Manuale utente
ARGON18
ARGON18 E-118 TRI+ Disc 315A Manuale utente
ARGON18
ARGON18 E-119 TRI Manuale utente
ARGON18
ARGON18 GALLIUM PRO 259A Manuale utente
ARGON18
ARGON18 E-117 TRI 285A Manuale utente
ARGON18
ARGON18 GALLIUM CS DISC 322A Manuale utente
ARGON18
ARGON18 KRYPTON PRO 333A Manuale utente
ARGON18
ARGON18 GALLIUM CS DISC 362A Manuale utente
ARGON18
ARGON18 E-112 Manuale utente
ARGON18
ARGON18 E-119 TRI+ Manuale utente
