Aries 2154001 Manuale utente

PAGE 1 • RC • 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Level of Difﬁculty

Easy

Parts List

1 Bull bar

2Driver / left

mounting bracket

2Passenger / right

mounting bracket

4 Hex bolt, M8

4 Flat washer, M8

4 Nylock nut, M8

4 Hex bolt, M10

8Flat washer, M10

4 Nylock nut, M10

4Bolt plate, M12

4 Flat washer, M12

4 Nylock nut, M12

1* LED wiring harness*

* Wiring harness only included

with LED equipped models

Scan

for helpful

install tips

INSTALLATION MANUAL

Tools Required

Ratchet Extension

Level Wrench, 18mm

Socket, 13mm Socket, 16mm

Socket, 17mm Socket, 18mm

Socket, 19mm

Product Image

2154001

2154101

2164001

2164101

Torque Speciﬁcations

METRIC

M6 bolt 3 ft.-lbs.

M8 bolt 7 ft.-lbs.

M10 bolt 16 ft.-lbs.

M12 bolt 28 ft.-lbs.

SAE

1/4" bolt 3 ft.-lbs.

5/16" bolt 7 ft.-lbs.

3/8" bolt 16 ft.-lbs.

7/16" bolt 20 ft.-lbs.

1/2" bolt 28 ft.-lbs.

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

For chrome powder coat, polish may be used to clear small scratches

and scuffs on the ﬁnish. Mild soap may be used also to clean the product.

For black ﬁnishes, mild soap may be used to clean the product.

Refer to the table to the left when securing hardware during the

installation process to help prevent damage to the product or vehicle.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • RC • PAGE 2

Step 1A - Vehicles without tow hooks

For vehicles with tow hooks,

skip to Step 2.

Locate the two mounting points on

the front end of the vehicle. Locate

the passenger-side mounting point.

Step 1B - Vehicles without tow hooks

Place the passenger-side mounting

bracket up to the frame of the vehicle.

Insert a M12 bolt plate into

each of the two mounting holes.

Secure the passenger-side mounting

bracket to the vehicle using a M12 ﬂat

washer and nylock nut on each of the

mounting points.

Repeat to install the

driver-side mounting bracket.

Step 2 - Vehicles with tow hooks

Remove the driver-side tow hook.

Keep the hardware to reuse later.

Place the driver-side mounting bracket

and the previously removed tow hook up

to the vehicle and secure the bracket and

tow hook using the previously removed

hardware.

Repeat to install the passenger-side

mounting bracket.

Step 3

To attach the bull bar mounting brackets,

lay the bull bar on a ﬂat surface. Insert

two M8 hex bolts into the inner rail slot.

PAGE 3 • RC • 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Step 4

Place the driver-side bracket over the

bolts and secure the bracket to the bull

bar using two M8 ﬂat washers and M8

nylock nuts.

Snug the hardware,

but do not fully tighten.

Repeat this step for the

passenger-side bracket.

Step 5

With help, lift the bull bar into place

and align the mounting tabs on the

outside of the mounting brackets.

Step 6

Insert a M10 hex bolt with ﬂat washer on

the outside of the bracket and a M10 ﬂat

washer and nylock nut on the inside.

Snug the hardware,

but do not fully tighten.

Repeat this process

for all mounting locations.

Level and adjust the bull bar into the

desired position and tighten all hardware.

Tighten all hardware to the

recommended torque speciﬁcations

listed in the table on the ﬁrst page.

If your bull bar is not equipped

with lights skip to step 9.

If your bull bar is equipped with lights

complete steps 7 and 8.

Note: If the LED lights are being used

with a 24V system, the 12V relay will

need to be replaced with a 24V unit.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • RC • PAGE 4

Step 9

Congratulations on the installation of

your new ARIES AdvantEDGE™bull bar.

With the bull bar installed, periodic

inspections should be performed to ensure

all mounting hardware remains tight.

To protect your investment, see the

'Notes and Maintenance' section on

the ﬁrst page of this instruction manual.

Step 8 - For Models with LED Lights Included

Connect the red fused wire with the ring

terminal to the positive battery post.

Connect the black wire ring terminal

to the negative battery post or other

suitable vehicle grounding point.

Mount the supplied relay to the vehicle

and secure all wires with zip ties away

from moving parts to avoid damage.

Test the lights to ensure proper function.

Step 7 - For Models with LED Lights Included

Disconnect the supplied switch

from the wire harness and install

in desired location.

With the switch installed, route the wire

harness to the LED lights and the switch.

Reconnect the blue, red and black spade

connectors to the switch as shown.

Note: The black wire connects

to the gold switch terminal.

Plug the male connector on the wire

harness into the female connector

attached to the LED lights.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente

Prorack

Prorack K1163 Manuale utente