Aries S224046 Manuale utente

Product Image

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

To protect the product, wax after installing. Regular waxing is recommended to

add a protective layer over the ﬁnish. Do not use any type of polish or wax that may

contain abrasives that could damage the ﬁnish.

For gloss black ﬁnishes, mild soap may be used to clean the product.

Level of Difﬁculty

Easy

Scan

for helpful

install tips

Front

Rear

INSTALLATION MANUAL S224046

Parts List

1Driver / left side bar

1Passenger / right side bar

6Mounting bracket, universal

13 Clip nut, 8mm

13 Hex bolt, 8mm x 25mm

13 Flat washer, 8mm

13 Lock washer, 8mm

13 Hex bolt, 10mm x 30mm

15 Flat washer, 10mm

14 Lock washer, 10mm

1Bolt plate, 10mm

2Hex nut, 10mm

1Plastic bolt retainer, 10mm

1Def-tank L-bracket

1Def-tank support bracket

Tools Required

Ratchet Socket, 16mm

Wrench, 16mm Socket, 13mm

Level

PAGE 1 • S224046-INS-RA • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • S224046-INS-RA • PAGE 2

Step 1

Locate the ﬁve mounting tabs along

the bottom edge of the vehicle body.

This installation will use the ﬁrst,

third and ﬁfth mounting tabs.

Step 2

Starting at the front driver side mounting

location, locate the threaded hole on

the inside of the body panel.

Attach a universal mounting bracket to

the body panel using an 8mm hex bolt

with a lock and ﬂat washer.

Snug the hardware,

but do not fully tighten.

Step 3

Rotate the bottom of the bracket

to the side to expose the hole in

the mounting tab.

Slide an 8mm clip-nut over the

mounting tab and rotate the bracket

back into position.

Secure the bracket with a second 8mm

hex bolt, lock washer and ﬂat washer.

Snug the hardware,

but do not fully tighten.

Step 4

Repeat steps 2 and 3 to install the

second bracket over the third

mounting tab location from step 1.

PAGE 3 • S224046-INS-RA • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Step 5

Locate the ﬁfth mounting tab from step 1

and remove the rubber plug from the

access hole.

Insert a clip nut through the access hole

and align it over the adjacent small hole.

Secure the top of the bracket with

an 8mm hex bolt, lock washer and

ﬂat washer.

Repeat step 3 to secure

the bottom of the bracket.

Step 6

Place the side bar onto the mounting

brackets and align the mounting points.

Note: If the holes on the side bar to

not match up with the brackets, ensure

all brackets have been installed in the

correct locations and the correct

side bar is being used.

Step 7

Secure the side bar to the brackets

using a 10mm hex bolt, lock washer and

ﬂat washer at each mounting location.

Snug the hardware,

but do not fully tighten.

Step 8

Adjust and level the side bar.

With the side bar in position, it is

recommended to tighten all brackets

to the vehicle ﬁrst, followed by the

side bar connections.

ARIESAUTOMOTIVE.COM • NEED ASSISTANCE? • 800.798.0813 • S224046-INS-RA • PAGE 4

Step 9

Repeat steps 1 through 8

on the passenger side.

Note: For diesel trucks, the front bracket

on the passenger side will require the

included def-tank brackets. Follow steps

10 through 15 to complete the install.

Step 11

Insert the 10mm bolt plate into

the access hole in the rocker panel.

Push the plastic retainer onto the

threaded end of the bolt plate to

help hold the plate in position.

Step 12

Select the def-tank L-bracket.

Attach the short end of the bracket to

the bolt plate with the ﬂat washer, lock

washer and 10mm hex nut.

Snug the hardware,

but do not fully tighten.

Step 10 2014 or older 2015 or newer

Locate the def-tank bracket

components for diesel truck models.

Begin the install by locating the round

factory hole in the bottom of the rocker

panel, closest to the front bracket

mounting location. The installation of

the bracket will vary depending on the

vehicle model shown to the right.

Remove the plastic plug to expose

the mounting hole in the rocker panel.

PAGE 5 • S224046-INS-RA • 800.798.0813 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM

Step 13

Slide an 8mm clip nut onto the mounting

tab. Fasten the side bar mounting

bracket with an 8mm hex bolt, ﬂat

washer and lock washer.

Snug the hardware,

but do not fully tighten.

Step 14

Bolt the def-tank support bracket to

the back of the def-tank L-bracket using

a 10mm hex bolt, ﬂat washer and lock

washer.

Snug the hardware,

but do not fully tighten.

Step 15

Repeat steps 6 through 8 on

the passenger side of the vehicle.

Congratulations on the installation

of your new ARIES 4" oval side bars.

With the side bars installed, periodic

inspections should be performed to ensure

all mounting hardware remains tight.

To protect your investment, see the

'Notes and Maintenance' section on

the ﬁrst page of this instruction manual.

Indice

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente

Prorack

Prorack K1163 Manuale utente