Arkel ARCUBE Manuale utente

ARCUBE Quick Installation Guide

Version : V1.01

ARCUBE

MONOBLOCK LIFT CONTROL UNIT

QUICK INSTALLATION GUIDE

ARCUBE Quick Installation Guide

Version : V1.01

Publisher Arkel Elektrik Elektronik San. ve Tic. A.Ş.

Eyüp Sultan Mah. Şah Cihan Cad. No:69

Sancaktepe/Istanbul 34885 TURKIYE

Tel: (+90 216) 540 03 10-11-12

Fax: (+90 216) 540 03 09

E-mail: info@arkel.com.tr

www.arkel.com.tr

Date of issue 11.2019

Document version V1.01

This document has been created to be a guide for Arkel customers. Reproduction, transfer, distribution or storage of part or

all of the contents in this document in any form without the prior written permission of Arkel is prohibited. Arkel reserves

the right to make changes and improvements to any of the products described in this document without prior notice.

Arkel is not responsible for those mistakes that may be found in this manual and for the damages that they may cause.

ARCUBE Quick Installation Guide 
 Version : V1.01 
 
 
 
CONTENTS 
ARCUBE MOUNTING..............................................................................................................................................5 
CONNECTIONS.........................................................................................................................................................5 
1 BRAKE RESISTOR CONNECTIONS ..........................................................................................................................5 
2 MOTOR PHASES AND PTC CONNECTIONS.............................................................................................................5 
3 MECHANICAL BRAKE CONNECTIONS....................................................................................................................6 
3.1 Asynchronous motor brake connections........................................................................................................................6 
3.2 Synchronous motor brake connections..........................................................................................................................6 
4 ENCODER CONNECTIONS ......................................................................................................................................6 
4.1 Asynchronous motor encoder connections....................................................................................................................6 
4.2 Synchronous motor encoder connections ......................................................................................................................6 
5 MOTOR FAN CONNECTION....................................................................................................................................6 
6 BATTERY PACK CONNECTION (IF NECESSARY).....................................................................................................6 
7 UPS CONNECTION ................................................................................................................................................6 
MENU..........................................................................................................................................................................7 
AUTO TUNING..........................................................................................................................................................7 
1 AUTO TUNING PREPARATION................................................................................................................................7 
1.1 Car top and pit inspection not connected.......................................................................................................................7 
1.2 Car top and pit inspection connected.............................................................................................................................7 
2 AUTO TUNING PARAMETER SETTINGS..................................................................................................................8 
2.1 Operation mode.............................................................................................................................................................8 
2.2 Motor type.....................................................................................................................................................................8 
2.3 Motor control type.........................................................................................................................................................8 
2.4 Nominal car speed.........................................................................................................................................................9 
2.5 Motor rpm......................................................................................................................................................................9 
2.6 Motor frequency............................................................................................................................................................9 
2.7 Motor current.................................................................................................................................................................9 
2.8 Motor voltage ................................................................................................................................................................9 
2.9 Motor direction..............................................................................................................................................................9 
2.10 High speed [Vmax]........................................................................................................................................................9 
2.11 Shaft position system.....................................................................................................................................................9 
2.12 Number of floors ...........................................................................................................................................................9 
2.13 Start auto-tune .............................................................................................................................................................10 
3 PERFORMING AUTO TUNING...............................................................................................................................10 
PREPARATIONS FOR NORMAL OPERATION................................................................................................10 
SHAFT LEARNING AND TEST DRIVE..............................................................................................................11 
CALL SETTINGS ....................................................................................................................................................13 
1 CAR CALLS .........................................................................................................................................................13 
1.1 FX-Cube settings.........................................................................................................................................................13 
2 LANDING CALLS .................................................................................................................................................14 
2.1 Serial installation.........................................................................................................................................................14 
2.2 Parallel installation......................................................................................................................................................14 
SOFTWARE UPDATE ............................................................................................................................................15 
ARCUBE PERIPHERALS ......................................................................................................................................15 
1 FX-CUBE ............................................................................................................................................................15 
2 MSP-16_EXP......................................................................................................................................................15 
3 ENCA.................................................................................................................................................................15 
4 ENCI ..................................................................................................................................................................16 

ARCUBE Quick Installation Guide 
 Version : V1.01 
 
 
 
9.5 BC-BUT.............................................................................................................................................................16 
9.6 BC-D2X .............................................................................................................................................................16 
9.7 BC-D3X .............................................................................................................................................................16 
9.8 BC-LCD10555...................................................................................................................................................16 
9.9 FX-CUBE-S.........................................................................................................................................................16 
9.10 CPC....................................................................................................................................................................16 
10. GENERAL DESCRIPTIONS..................................................................................................................................16 
10.1 CLEARING OF PERMANENT ERRORS....................................................................................................................16 
10.2 BYPASS SOCKET .................................................................................................................................................16 
10.3 INSPECTION HAND TERMINALS...........................................................................................................................16 
10.4 BACK TO NORMAL OPERATION FROM PIT INSPECTION .......................................................................................16 
11. ERROR CODES, POSSIBLE REASONS AND SOLUTIONS ............................................................................17 
 
FIGURE LIST 
FIGURE 1 ARCUBE MECHANICAL SIZE....................................................................................................................................5 
FIGURE 2 BRAKE RESISTOR AND BATTERY PACK SIZE (*).......................................................................................................5 
FIGURE 3 MENU.....................................................................................................................................................................7 
FIGURE 4 REQUIRED BRIDGING WHEN THE CAR TOP AND PIT INSPECTION NOT CONNECTED............................................7 
FIGURE 5 REQUIRED BRIDGING WHEN THE CAR TOP AND PIT INSPECTION CONNECTED....................................................8 
FIGURE 6 RECALL TERMINAL..................................................................................................................................................8 
FIGURE 7 INSTALLATION OF BOTTOM ROUND MAGNETS FOR SKSR1 ................................................................................11 
FIGURE 8 INSTALLATION OF TOP ROUND MAGNETS FOR SKSR2 ........................................................................................11 
FIGURE 9 INSTALLATION OF MAGNETS FOR SML1-SML2 DOOR ZONE SENSORS................................................................11 
FIGURE 10 SHAFT LEARNING SCREEN..................................................................................................................................12 
FIGURE 11 CAR CALL SCREEN...............................................................................................................................................13 
FIGURE 12 LOP LEARNING ENABLED ...................................................................................................................................14 
FIGURE 13 LOP LEARNING DISABLED...................................................................................................................................14 
FIGURE 14 LEARNED LOP SCREEN........................................................................................................................................14 
FIGURE 15 BYPASS SOCKET..................................................................................................................................................16 
 
 
 
 
 
 
 

ARCUBE Quick Installation Guide

Version : V1.01

1. ARCUBE Mounting

Mount ARCUBE monoblock unit, brake resistor, battery pack and UPS (If required).

Figure 1 ARCUBE Mechanical Size

Figure 2 Brake Resistor and Battery Pack Size (*)

* These sizes are valid only if they are supplied by ARKEL.

2. Connections

Make connections of motor supply, motor PTC, brakes

and their checkback contacts, motor fan, encoder, brake

resistor and battery pack with UPS (If required).

2.1 Brake Resistor Connections

2.2 Motor Phases and PTC Connections

ARCUBE Quick Installation Guide

Version : V1.01

2.3 Mechanical Brake Connections

2.3.1 Asynchronous motor brake connections

2.3.2 Synchronous motor brake connections

2.4 Encoder Connections

2.4.1 Asynchronous motor encoder connections

2.4.2 Synchronous motor encoder connections

2.5 Motor Fan Connection

2.6 Battery Pack Connection (If necessary)

2.7 UPS Connection

If you do not have UPS, you must bridge connectors U-

LI with U-LO and U-NI with U-NO using with suitable

cables. Otherwise you can’t run the system.

* For BL1-BL2, look at your distribution panel.

ARCUBE Quick Installation Guide

Version : V1.01

3. Menu

When the system is energized, ARCUBE screen on the

motor driver will be displayed. In order to enter the menu

YELLOW button “ENT”, to exit from the menu RED

button “ESC”are used. You can scroll through

parameters with “UP”, “DOWN” buttons. As you are on

the parameter you wanted to enter inside, after pressing

“ENT” button, you can go to the different values and

options in the parameter by using “UP”, “DOWN”

buttons.

Figure 3 Menu

4. Auto Tuning

Before the lift is run, auto tuning process must be

performed. The characteristic of motor is learned during

the auto tuning process. Since the auto tuning is

performed with hand terminal, recall hand terminal key

should be activated. ARCUBE unit should be energized

for performing of auto tuning.

➢Connect the mains supply of unit. (L1, L2, L3, N,

PE)

4.1 Auto Tuning Preparation

While performing autotune, the required bridging will be

different depending on if car top and pit inspection is

connected in the system or not. Therefore, it is so

important to choose the correct parameter from the menu.

“OPERATION MODE”parameter under “QUICK

INSTALLATION”must be definitely set correctly.

4.1.1 Car top and pit inspection not connected

In the first installation, if the auto tuning is performed as

“car top and pit inspection not connected”, from the

parameter;

“OPERATION MODE”“INSTALLATION MODE”

“WITHOUT INSPECT BOX”

must be chosen. In the case of wrong choice, Arcube

would not communicate with Fx-Cube board and raise an

error. The required safety circuit bridging must be as

shown in Figure 4.

Figure 4 Required bridging when the car top and pit

inspection not connected

4.1.2 Car top and pit inspection connected

If the auto tuning is performed as “car top and pit

inspection connected”, from the parameter;

“OPERATION MODE”“INSTALLATION MODE”

“WITH INSPECTION BOX”

must be chosen. The choice of this parameter is

important. If it is set wrongly, 817, 818, 868 and 869

signals will be ignored by ARCUBE. The required safety

circuit bridging must be as shown in Figure 5.

There must not be bridge between 119B-120 and 111-

113. In this step, if it is assumed that the doors are not

mounted, only the doors (120-130-135-140) will be

bridged.

ARCUBE Quick Installation Guide

Version : V1.01

Figure 5 Required bridging when the car top and pit

inspection connected

The bridging should be only done during the first

installation. After the car top and pit inspection

terminals are connected, the bridges must be

removed!

4.2 Auto Tuning Parameter Settings

Take the lift to recall mode by switching the recall key

(SEE) to “1” position in the recall terminal located in the

control panel. In this step, the motor can be moved by up

and down buttons (SEEU, SEED).

Figure 6 Recall terminal

After making the system prepared to auto tuning, the

required parametric settings must be done on LCD

screen.

Turn on all the fuses on ARCUBE, then turn on “SMP”

switch over the distribution panel.

After the screen is displayed, press “ENT”button in

order to enter the menu. When you see “QUICK

INSTALLATION”screen, press “ENT” button one

more time and set the parameters as shown below step by

step according to your system.

4.2.1 Operation mode

This should be chosen correctly depending on if the car

top and pit inspection terminal is connected or not.

4.2.2 Motor type

Motor type must be chosen correctly as asynchronous or

synchronous.

4.2.3 Motor control type

Motor control type must be chosen correctly as open

loop or closed loop.

*Only closed loop option exists for the synchronous

motors.

ARCUBE Quick Installation Guide

Version : V1.01

4.2.4 Nominal car speed

This is the speed value what motor label shows.

4.2.5 Motor rpm

Motor revolution per minute (rpm) value must be entered

correctly as shown in the motor label.

4.2.6 Motor frequency

Motor frequency value must be entered correctly as

shown in the motor label.

4.2.7 Motor current

Motor current value must be entered correctly as shown

in the motor label.

4.2.8 Motor voltage

Motor voltage value must be entered correctly as shown

in the motor label.

4.2.9 Motor direction

This parameter can be changed after completing auto

tuning if the direction of move is wrong.

4.2.10 High speed [Vmax]

This is the parameter which sets the max. speed the car

moves. The value of this parameter should be maximum

what the nominal motor speed is.

4.2.11 Shaft position system

Shaft positioning system must be entered here correctly.

4.2.12 Number of floors

The floor number of the system must be entered here

correctly.

ARCUBE Quick Installation Guide

Version : V1.01

4.2.13 Start auto-tune

ARCUBE can perform auto tuning both with ropes and

without ropes. “START AUTO-TUNE”parameter

must be entered correctly.

Save the parameters and exit by pressing “ESC”button.

4.3 Performing Auto Tuning

After completing the above steps, exit by pressing

“ESC”button. After the changes are being saved, it turns

back to main menu and the below screen is come across.

Take the “SEE” key on ARCUBE to “1” position and

keep pressing up or down recall buttons until “MOTOR

TUNE SUCCEED”screen is seen. After you see this

message, save the values by pressing “ENT”button.

Then, try to move the car a little.

If the motor turns in a wrong direction when you press

down or up buttons: find “2.5: MOTOR DIRECTION”

parameter under “2-BASIC SETTINGS”title and

change the parameter. If it is chosen as “clockwise”,

choose “counter-clockwise”. If it is chosen as “counter-

clockwise”, choose “clockwise”.

If the car moves correctly in the recall mode, you can go

on the following steps.

Remove all the bridges between 110-140 terminals

in the safety circuit.

After this step, after car top and pit inspection

terminal mounting are completed, the parameters

must be corrected. The bridges must be removed.

After the magnetic switches and magnets are

mounted, the parameters must be corrected. The

bridges must be removed. Otherwise, the priority of

the person in the pit according to the person on the

car top, and the priority of the person on the car top

according to the person on the control panel will be

disappeared.

5. Preparations for Normal Operation

Make all the other mechanical installations of elevator

system.

Make the inspection box wiring, pit box wiring and safety

circuit wirings.

Up and down deceleration distance magnets should be

put 2 m away from the top and bottom door zone magnet

levels.

Make the installation of round magnets for SKSR1

magnetic switch 2 m away from bottom floor door zone

magnet level. Connect the cables of SKSR1 magnetic

switch to 100 and 817 terminals located on Fx-Cube

board.

Move the car to the bottom floor.

Car must be exactly at the bottom floor level.

Install round magnet with red color side above the

SKSR1 magnetic switch as deceleration distance.

Install the round magnet with black color side a little

above the red color magnet.

The distance between magnetic switch and magnets must

be 1-2 cm.

Indice

Altri manuali Arkel Unità di controllo

Arkel

Arkel ARCODE 4B26A Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente