Armstrong FTV Manuale utente

FILE NO: 35.815IN

DATE: Aug. 25, 2011

SUPERSEDES: New

DATE: New

INSTALLATION AND OPERATING INSTRUCTIONS

Armstrong Model FTV

350mm to 600mm

Flo-Trex Valve

TABLE OF CONTENTS

Section Page

1.0 - Introduction.............................................................................................................................................2

1.1 - Warning ..................................................................................................................................................2

2.0 - Installation ..............................................................................................................................................3

3.0 - Storage...................................................................................................................................................3

4.0 - Cleaning .................................................................................................................................................3

5.0 - Maintenance...........................................................................................................................................3

6.0 - Disassembly & Assembly .......................................................................................................................4

Page 1 of 4

1.0 - INTRODUCTION

The Armstrong Model FTV Flo-Trex Combination Valves are designed for installation on the discharge side of

centrifugal pumps. The Armstrong Combination Valve incorporates three functions in one valve:

• Drip-tight shut-off valve

• Spring-closure design, non-slam check valve

• Flow throttling valve

1. Body

2. Cover

3. Valve Seat

4. Disc

5. Disc Holder

6. Lower Stem

7. Upper Stem

8. Spring

9. Guide Bushing

10. Handle

1.1 - WARNING

These instructions must be read, understood and followed before attempting to install, maintain or operate this

equipment. Otherwise severe personal injury or damage to equipment may result.

Before installing the Flo-Trex valve, make sure that there is enough room provided to disassemble the valve

for maintenance.

Before undertaking any maintenance on the Flo-Trex valve, it must be isolated from the system line and any

pressure must be allowed to normalize to atmosphere.

Valves that remain in one position for long periods of times may be subject to some degree of reduced

operability as a result of loss of effective lubricants in threads, aging of gasket, surface corrosion of moving

parts, or accumulation of foreign solids. Refer to this manual’s recommended maintenance section to maintain

valve performance.

2.0 - INSTALLATION

The valve should be mounted to a spool piece on the discharge side of the pump. Spool piece length is based

on a minimum recommended space of 2 times the pipe diameter (e.g.: 350mm discharge requires 350mm D x

711mm L spool piece).

Page 2 of 4

It is not recommended to mount a valve directly to the pump as this could cause undesirable noise in

the system.

Sufficient clearance around the valve should be left for valve removal or repair.

Install valve in the direction of the flow arrows on the valve body.

The valve body has been designed to handle the weight of the pump on vertical in-line installations. The body

is not designed to support the piping weight. It is recommended that the piping be supported by hangers. Pipe

supports should be provided under the valve and strainer bodies.

Ensure that the Flo-Trex is installed with the valve stem in the upright position. Valve slam may occur if

installed in any other configuration.

3.0 - STORAGE

The Flo-Trex valve must be examined for signs of damage that may have occurred during transportation.

The Flo-Trex valve should be stored in a suitably sheltered environment to protect it from the effects of

weather, dust, dirt, and moisture.

The Flo-Trex valve is shipped with end caps on the inlet and outlet ends. These end caps should be left in

place until it is ready for installation.

The Flo-Trex valve should be stored at a constant temperature between -10°C to 40°C (14°F to 104°F).

4.0 - CLEANING

The Flo-Trex valve has been cleaned, inspected, and sealed at the factory prior to shipment. The protective

end caps will guard against entry of foreign matter and no additional cleaning should be required. A visual

examination of the interior of the body should be made to ensure that the Flo-Trex valve is free of contaminants.

5.0 - MAINTENANCE

The Flo-Trex valve requires inspection and periodic maintenance at regular intervals to maintain optimum valve

performance and prolong equipment life.

The troubleshooting chart presented in the following table lists typical problems and methods for resolving

them. It should be noted that this chart does not present all possible problems or all possible solutions.

Problem Possible Cause Solution

Leakage • Disc may fail to seat

(Foreign material lodged in orifice)

• Valve installed backwards

• Disassemble and clean

• Re-install in the direction of the

flow arrows

Pump overloading • Valve may be closed or slightly opened

• Incorrect selection of valve size • Fully open the valve

• Re-size the valve

Water hammer • Buckling of stem. Foreign material lodged

in stem etc.

• Damage of the disc or seat

• Disassemble and check the stem

• Disassemble and check the disc

and seat

Page 3 of 4

6.0 - DISASSEMBLY & ASSEMBLY

General: Before beginning to disassemble the Flo-Trex valve, become fully familiar with the construction

details and disassembly and re-assembly instructions prior to beginning any work.

Before undertaking any maintenance on the Flo-Trex valve it must be isolated from the system and any

pressure must be allowed to safely normalize to atmosphere.

To ensure that the Flo-Trex valve is re-assembled properly, it is necessary to mark certain parts and measure

and record certain dimensions. Additionally, ensure that spare and replacement parts such as o-rings,

gaskets, etc. are on hand before beginning the disassembly procedure.

6.1 - DISASSEMBLY

CAUTION: The Flo-Trex valve must be isolated from the system line and any pressure must be allowed

to normalize to atmosphere.

Remove handle by disengaging lock-nut from the stem.

Disassemble the travel indicator by removing the snap ring.

Unscrew guide bushing (The o-ring / gasket must be thoroughly cleaned. If there are any indications of

wear and/or scratches, they must be replaced.)

Release hex bolts and turn anti-clockwise until spring is slack.

Disassemble the cover, upper stem, spring and gasket. (The upper and lower stem, seat and disc must

be thoroughly cleaned. If there are any indications of bending, wear and/or scratches, they must

be replaced.)

When disassembling the disc assembly (disc holder, disc, lower stem) carefully lift the stem assembly

straight out of the body in order to avoid causing unnecessary damage.

If there is no damage to the seating surface, do not disassemble the seat.

6.2 - ASSEMBLY

Prior to assembly, be sure that all parts are clean and reassemble in reverse order of the disassembly.

Check to see that flange gaskets are properly positioned before tightening the bolts.

Tighten bolts gradually in a back and forth clockwise rotation.

Gradually adjust the stem until the proper flow rate is reached.

S. A. Arms

23 Bertrand Avenue

Toronto, Ontario

Canada, M1L 2

T: 416-755-2

F: 416-759-9

trong Limited Armstrong Integrated Limited Armstrong Design Private Ltd.

Wenlock Way (Unit 1 - Armstrong Manufacturing Center)

Manchester 490-L, 4th Phase, Peenya Industrial Area,

P3 United Kingdom, M12 5JL Bangalore, India 560 058

291 T: +44 (0) 8444 145 145 T: +91(80) 4906 3555

101 F: +44 (0) 8444 145 146 F: +91(80) 2334 3535 © S.A. Armstrong Limited 2011

Page 4 of 4

For Armstrong locations worldwide, please visit www.armstrongintegrated.com

Altri manuali Armstrong Unità di controllo

Armstrong

Armstrong CD72SR Manuale utente

Armstrong

Armstrong 425 Manuale di istruzioni

Armstrong

Armstrong Flex Flange Manuale utente

Armstrong

Armstrong OB-2000PT Integral Manuale utente

Armstrong

Armstrong OB 2000PT Manuale

Armstrong

Armstrong Steamix VE-M Manuale di istruzioni

Armstrong

Armstrong GP-2000 Manuale utente

Armstrong

Armstrong TVS-800 Series Manuale utente

Armstrong

Armstrong 3750 Manuale utente

Armstrong

Armstrong BRAIN DMC80 Manuale utente

Armstrong

Armstrong A Series Manuale utente

Armstrong

Armstrong 320 Manuale di istruzioni

Armstrong

Armstrong 880A Series Manuale utente

Armstrong

Armstrong GD-30 Manuale utente

Armstrong

Armstrong The Brain DRV25 Manuale utente

Armstrong

Armstrong TVS 4000F Manuale utente

Armstrong

Armstrong DRV40 Manuale utente

Armstrong

Armstrong The Brain DRV25 Manuale utente

Armstrong

Armstrong 880100-002 Manuale utente

Armstrong

Armstrong 880 Series Specifiche tecniche

Armstrong

Armstrong 1-AV Manuale utente

Armstrong

Armstrong Emech F3 Manuale di istruzioni

Armstrong

Armstrong The Brain DRV80 Manuale utente

Armstrong

Armstrong Emech F5 Manuale di istruzioni

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente