Arris Ruckus E510 Manuale utente

Unleashed E510

AP Module

Quick Setup Guide

The Unleashed E510 is a modular outdoor Access Point

designed for deployment scenarios where the antenna

structure and onboard AP intelligence must be physically

separated.

In addition to this

Unleashed E510 AP Module Quick Setup

Guide

, the E510 AP also includes the following documents

(please refer to the relevant documents for detailed

information on other E510 modules):

E510 Component Document

E510 Antenna Module (PN#:

902-2101-0000)

E510 Access Point Antenna

Module Quick Setup Guide

E510 USB Cable (PN#:

902-2003-0000)

E510 Access Point USB

Cable Quick Setup Guide

WARNING! Only trained and qualiﬁed personnel should be

allowed to install, replace, or service this equipment.

WARNING! Installation of this equipment must comply with

local and national electrical codes.

CAUTION! Make sure that you form a 80mm - 130mm

(3”-5”) drip loop in any cable that is attached to the AP or

the building. This will prevent water from running along the

cable and entering the AP or the building where the cable

terminates.

CAUTION! Be sure that grounding is available and that it

meets local and national electrical codes. For additional

lightning protection, use lightning rods and lightning

arrestors.

CAUTION! Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING! Ruckus Wireless strongly recommends that you

wear eye protection before mounting the AP.

This Guide in Other Languages

•请从以下网站获得该指南的简体中文版 https://

support.ruckuswireless.com.

• Vous trouverez la version française de ce guide à l'adresse

suivante https://support.ruckuswireless.com.

•このガイドの日本語版は https://

support.ruckuswireless.com でご覧ください。

•이가이드의 한국어 버전은 웹사이트 (https://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

• Veja a versão em português (Brasil) deste guia em https://

support.ruckuswireless.com.

• Puede ver la versión en español (América Latina) de esta

guía en https://support.ruckuswireless.com.

Before You Begin

Before deploying Ruckus Wireless products, please check for

the latest software and the release documentation.

• Release Notes and other user documentation are available

at http://support.ruckuswireless.com/documents.

• Software upgrades are available at http://

support.ruckuswireless.com/software.

• Open source information is available at http://

opensource.ruckuswireless.com.

• Software license and limited warranty information are

available at http://support.ruckuswireless.com/warranty.

Before deploying your Ruckus Wireless Access Point, verify

that all items listed in

Package Contents

are included in the

package. If any item is damaged or missing, notify your

authorized Ruckus Wireless sales representative. Also,

make sure that you have the required hardware and tools.

Required Hardware and Tools

• Torque wrench or torque screwdriver with sockets, or SMA

torque wrench, for cable connections

• T10 Security Torx screwdriver/bit for reset button access

• Mounting bracket (purchased separately) for pole mounting

• Customer-supplied mounting bracket for DIN rail mounting

• Electric drill with drill bits and customer-supplied wall

anchors, ﬂat washers, and hex nuts for ﬂat-surface

mounting

AP Module Package Contents

The E510 AP Module installation package includes all of the

following:

• E510 Embedded Access Point Module

• Service Level Agreement/Limited Warranty Statement

• Declaration of Conformity

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• This Quick Setup Guide

FIGURE 1 E510 AP Module

Purchased Separately

The E510 requires an Antenna Cable Kit and Antenna Module

(Ruckus or third-party RF cables) to be purchased separately.

NOTE: BeamFlex is not supported when using third-party

RF cables.

Antenna Module

The E510 Antenna Module (Ruckus PN# 902-2101-0000)

consists of one vertically-polarized and one horizontally-

polarized antenna per band. Refer to the

E510 Antenna

Module Quick Setup Guide

for more information.

Antenna Cable Kit

Ruckus provides three different cable kits with different length

cables. Each kit contains two RF coaxial cables and one

Control cable. The RF cables are used to connect the AP

Module to the Antenna Module using two RP-SMA

connectors (each dual-band/single chain).

• 902-2000-0000 E510 Antenna Cable (60 cm length)

• 902-2001-0000 E510 Antenna Cable (150 cm length)

• 902-2002-0000 E510 Antenna Cable (300 cm length)

Published March 2018, Part Number 800-71723-001 Rev A

CAUTION! If third-party RF cables are used, the customer is

responsible for entering the correct signal loss proﬁle /

antenna gain in the SmartZone GUI.

Mounting Bracket

The E510 AP Module Mounting Bracket (Ruckus PN#

902-2004-0000) must be purchased separately for mounting

the AP Module to a pole. The pole mounting bracket kit

includes the following:

• Pole mount bracket

• 3 M4x8mm bracket screws with built-in lock washers and

ﬂat washers

• 4 metal pole clamps

M8 and M12 Connectors

If third-party Ethernet or DC power cables are used, the

installer must ensure the proper cable connectors are used.

The following are examples of third-party cable connectors

that can be used with the E510:

• M12 X-coded 8 position PoE connector:

https://

www.digikey.com/product-detail/en/te-connectivity-amp-

connectors/2120952-1/A120858-ND/5118752

• M8 A-coded 3 position connector:

http://www.te.com/usa-

en/product-T4010008031-000.html

Unleashed Network Conﬁguration

Setup Using the Unleashed Mobile App

To perform setup using the Unleashed Mobile App, download

the iOS or Android app from the app store.

1. As soon as the Unleashed AP is powered on and

connected to the local network, it boots up and begins

broadcasting a temporary unencrypted WLAN named

“Conﬁgure.Me-[xxxxxx]” from both radios.

2. Using your client’s Wi-Fi connection settings, select and

associate to the “Conﬁgure.Me-[xxxxxx]” WLAN.

3. Launch the app, and follow the on-screen instructions to

conﬁgure your Unleashed network(s).

FIGURE 2 Unleashed Mobile App for iOS and Android

FIGURE 3 Conﬁguring Unleashed from the Mobile App

Setup Using a Web Browser

1. As soon as the Unleashed AP is powered on and

connected to the local network, it boots up and begins

broadcasting a temporary unencrypted WLAN named

“Conﬁgure.Me-[xxxxxx]” from both radios.

2. Using your client’s Wi-Fi connection settings, select and

associate to the “Conﬁgure.Me-[xxxxxx]” WLAN.

3. Launch a web browser and enter the following into the

browser’s URL bar:

unleashed.ruckuswireless.com

, and

press Enter.

4. You will be redirected to the Setup Wizard. Complete the

steps in the Setup Wizard and click Finish.

FIGURE 4 Complete the Setup Wizard to set up your Unleashed network

5. Once the Setup Wizard is ﬁnished, a “Conﬁguring system

settings and rebooting” progress screen appears. Wait

until the process is complete.

6. Connect to the WLAN that you conﬁgured in the Setup

Wizard, and click OK to reconnect. You will be redirected

to the Unleashed login screen.

7. Enter your Admin Name and Password to login.

FIGURE 5 The Login page

8. Upon successful login you will be presented with the

Unleashed Dashboard, which displays an overview of your

Ruckus Unleashed network.

Mounting Instructions

Published March 2018, Part Number 800-71723-001 Rev A

Mounting Scenarios

The E510 is designed for embedded mounting into third-party

structures such as light poles, light ﬁxtures, street furniture,

railway carriages and track side installations.

Surface Mounting

The AP Module supports mounting on a ﬂat surface into which

holes can be drilled.

Use customer-supplied hardware to mount the AP Module to

a ﬂat surface.

FIGURE 6 E510 AP Module ﬂat surface mounting ﬂanges

Pole Mounting

The E510 AP Module can be mounted on a pole with the

E510 AP Module Mounting Bracket (PN# 902-2004-0000).

NOTE: The included hose clamps can support a pole

diameter up to 120mm, when daisy-chained together.

1. Attach the mounting bracket to the AP Module using the

three M4 bracket screws with built-in ﬂat washers and

lock washers included in the bracket kit. Torque screws to

20 in-lbs (2.26 Nm).

NOTE: The AP Module can be mounted either ﬂat to

the pole or side-mounted. The bracket provides holes

to accommodate both scenarios. Side mounting uses

three screws and ﬂat mounting uses two screws.

FIGURE 7 Attaching the bracket to the side of the AP

FIGURE 8 Attaching the bracket to the back of the AP

2. Use the two metal pole clamps to attach the bracket to

the pole. Tighten pole clamp screws to 27 in-lbs. (3.05

Nm).

FIGURE 9 AP Module pole mounting - side

FIGURE 10 AP Module pole mounting - ﬂat

DIN Rail Mounting

The AP Module supports mounting onto DIN Rail brackets via

a separate third-party bracket accessory.

Connecting the AP Module to the Antenna

Module

When a Ruckus Beamﬂex antenna, such as 902-2101-0000,

is used, the E510 AP Module must be connected to the

Antenna Module using two RF cables and one Control Cable.

NOTE: For Antenna Mounting and Orientation, please refer

to the

E510 Antenna Module Quick Setup Guide

The E510 AP module has two RP-SMA connectors for

antenna RF cables to connect with the external antenna

module. The 2.4 GHz and 5 GHz Wi-Fi RF signals are carried

between the AP Module and Antenna Module using the two

SMA cables.

The length of the cables depends on the needs of the

installation, and cables are therefore purchased separately to

suit the particular deployment.

TABLE 1 Antenna loss by cable length

Cable Length [m] 2.4 GHz

Loss [dB]

5 GHz Loss

[dB]

902-2000-00

0.6 0.5 1

902-2001-00

1.5 1 1.5

902-2002-00

323

Published March 2018, Part Number 800-71723-001 Rev A

Please refer to the

E510 Antenna Module Quick Setup Guide

for antenna cable details.

1. Connect the antenna cables to the ANT1 and ANT2

connectors on the AP Module and the Antenna Module

respectively.

FIGURE 11 Connect the AP Module to the Antenna Module

WARNING! Be sure that you connect the correct

antenna cable to the correct port (ANT1 to ANT1, ANT2

to ANT2). Do NOT connect ANT1 to ANT2.

2. Using a torque wrench/screwdriver with an SMA (5/16)

adapter, tighten the antenna cable connectors to 8 in-lbs.

(0.9 N.m).

3. Connect the M12 antenna Control Cable to the M12

connector (female) on the AP module.

4. Connect the other end of the M12 antenna Control Cable

to the M12 connector (male) on the Antenna module.

FIGURE 12 E510 Antenna Module connectors

NOTE: The Control Cable has one male and one female

connector to prevent installing the cable incorrectly.

Power Input

The E510 can accommodate two sources of power, 802.3af

PoE power or 12V‐48V DC.

The E510 can be powered by 802.3af PoE switch or Ruckus-

supplied PoE injector.

Alternately, power can be supplied from a DC power source

using the M8 connector.

When both power sources exist, 12‐48V DC takes priority

over PoE Power.

NOTE: For information on the recommended M8 cable

connectors for the E510, refer to the

M8 and M12

Connectors

section in

Purchased Separately

, above.

FIGURE 13 E510 DC power and PoE In ports

Connecting the Ethernet Cable

The E510 has one 10/100/1000 PoE Ethernet port with M12

weatherproof connector.

Connect the Ethernet cable to a 802.3af-compliant PoE

switch or injector to provide both power and network

connectivity.

NOTE: For information on the recommended M12 cable

connectors for the E510, refer to the

M8 and M12

Connectors

section in

Purchased Separately

, above.

Factory Reset Button

The Reset button can be accessed by removing the Torx

screw labeled RESET.

Use a T10 Security Torx screwdriver or bit to remove the Torx

screw covering the Reset button.

Insert a pin or similar object less than 2.5 mm in diameter into

the reset hole to reboot or factory reset the device.

Press and release the reset button to reboot the AP. Press and

hold the reset button for 4+ seconds to restore to factory

defaults.

FIGURE 14 Remove Torx screw to access Reset button

CAUTION! Remember to replace the Torx screw covering

the Reset button after use. Insert the screw and torque to 4

in-lbs. (0.45 Nm).

USB Port

E510 has one USB 2.0 port as an M8 IP67 connector

(Female). This port provides both a data connection and

power output for an IoT device such as a BLE Smart Beacon

or ZigBee dongle.

A USB cable with an M8 connector at one end and a USB 2.0

Type-A connector at the other end can be attached to the

female M8 connector on the E510 AP module.

A USB Module Accessory can be purchased separately, and

comes with a 3m USB cable (Ruckus PN# 902-2003-0000).

NOTE: Please refer to the

E510 USB Cable Quick Setup

Guide

for more information.

FIGURE 15 E510 USB port, Control cable and Antenna cable connectors

Ruckus, Ruckus Wireless, the Ruckus logo, and the Big Dog design are

trademarks of Ruckus Wireless, Inc., a wholly owned subsidiary of ARRIS

International plc. ARRIS is a trademark of ARRIS Enterprises LLC. All other

trademarks are the property of their respective owners.

Published March 2018, Part Number 800-71723-001 Rev A

Altri manuali per Ruckus E510

Altri manuali Arris Unità di controllo

Arris

Arris C4 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente