ATEN CS-62A Manuale utente

User Manual

CS-62A

Read this guide thoroughly and follow the installation and operation

procedures carefully in order to prevent any damage to the unit and/or

any devices that connect to it.

This package contains:

M1 CS-62A Two Port Petite KVM Switch with Attached Cables

M1 User Manual

If anything is damaged or missing, contact your dealer.

Manual Part No. PAPE-1212-2AT

Printed in Taiwan 06/2003

All brand names and trademarks are the registered property of their respective owners.

2003-06-10

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy, and if not installed and

used in accordance with the instruction manual,may cause

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

MReorient or relocate the receiving antenna;

MIncrease the separation between the equipment and

receiver;

MConnect the equipment into an outlet on a circuit different

from that which the receiver is connected;

MConsult the dealer or an experienced radio/television

technician for help.

2003-06-10

Overview

The CS-62APetite KVM Switch is a control unit that allows

access to two computers from a single console (keyboard,

monitor, and mouse). Before the development of the CS-62A,

the only way to control multiple computer configurations from a

single console was through a complex and costly network

system. Now, with the CS-62APetite KVM Switch, you can

easily access two computers in a cost effective manner.

The CS-62Aimproves on previous models with a 50% smaller

footprint and attached custom KVM cables, resulting in a neat

and tidy workspace and trouble-free installation.

Recognizing the increased importance of sound, the CS-62Ais

speaker enabled. You can listen to the audio output of both

computers (one at a time) on a single set of speakers.

Setup is fast and easy; plugging cables into their ports is all that

is entailed. The KVM focus is toggled between the computers

by means of simple Hotkey combinations entered from the

keyboard.

There is no software to configure, no installation routines, and

no incompatibility problems. Since the CS-62Aintercepts

keyboard input directly, it works on any hardware platform and

with all operating systems.

There is no better way to save time and money than with a

CS-62Ainstallation. By allowing a single console to manage

both computers, the CS-62Aeliminates the expense of

purchasing a separate keyboard, monitor, and mouse for each.

Additionally, it saves the extra space they would take up, and

eliminates the inconvenience and wasted effort involved in

constantly having to move from one computer to the other.

- 1 -

2003-06-10

Features

MOne console controls two computers

MCompact design features two attached KVM (keyboard,

video, mouse, and speaker) cables

MSpeaker enabled

MEasy to install - no software required - connecting cables to

the computers is all it takes

MEasy to operate - computer selection via Hotkeys - Auto

Scan function to monitor computer operation

MHot pluggable - add or remove computers for maintenance

without powering down the switch

MLED display for easy status monitoring

MKeyboard and mouse emulation for error free computer

booting

MSupports Microsoft IntelliMouse and the scrolling wheel on

most mice

MCaps Lock, Num Lock, and Scroll Lock states are saved and

restored when switching

MSuperior video quality - up to 2048 x 1536; DDC2B

MCompatible with all operating platforms

MNon-powered

- 2 -

2003-06-10

Hardware Requirements

Console

MA VGA, SVGA, or Multisync monitor capable of the highest

resolution that you will be using on any computer in the

installation

MA PS/2 Style Mouse

MA PS/2 Keyboard

Computers

The following equipment must be installed on each computer

that is to be connected to the system:

MA VGA, SVGA or Multisync card.

MA 6-pin mini-DIN (PS/2 style) mouse port.

MA 6-pin mini-DIN (PS/2 Style) keyboard port.

Cables

For optimum signal integrity and to simplify the layout, two high-

quality 4-in-1 CS Custom KVM cables have been designed into

the CS-62APetite KVM Switch. There is no need for a separate

cable purchase.

Note: The KVM cables have PS/2 style keyboard and mouse

connectors. The CS-62Adoes not support AT

keyboards or serial mice.

- 3 -

2003-06-10

Front View

1. Port LEDs

A LED lights to indicate its corresponding port is the one that

has the KVM focus. Depending on the port’s status, the LED

may flash according to a specific pattern (see the LED

Display Table, p. 8, for details).

2. KVM Cables

These 4-in-1 cables connect to the the keyboard, video,

mouse, and audio ports on the computers you are installing

(see the diagram on p. 6).

3. Speaker Jack

The cable from your speakers plugs in here.

4. Console Ports

Your keyboard, monitor, and mouse plug in here. Each port

is marked with an appropriate icon to indicate itself.

- 4 -

2003-06-10

Installation

Refer to the Installation diagram on the next page as you

perform the following steps:

1. Plug your keyboard, monitor, and mouse into the appropriate

Console ports of the CS-62APetite KVM Switch. Each port is

labeled with an appropriate icon to indicate itself.

2. (Optional) Plug your speakers into the CS-62A’s speaker

jack.

3. Plug the attached KVM cables’ keyboard, monitor, mouse,

and speaker connectors into their respective ports on the

computers you are installing.

4. Turn on the power to the computers.

Note: The CS-62A’s Power On default is to link to the first

computer you turn on.

- 5 -

1. Before you begin, make sure that power to all the

devices you will be connecting up have been

turned off. You must unplug the power cords of

any computers that have the Keyboard Power On

function. Otherwise, the switch will receive power

from the computer.

2. To prevent damage to your equipment, make sure

that all devices you will be connecting up are

properly grounded.

2003-06-10

- 6 -

2003-06-10

Operation

Accessing both of your computers from a single console could

not be easier. The CS-62Auses Hotkey combinations to

provide KVM focus to the computers. The Hotkey combinations

allow you to:

MSelect the Active Port

MInvoke Auto Scan Mode

MSet the Auto Scan Time Interval

Selecting the Active Port

You can toggle the KVM focus between the two computers by

pressing and releasing the Scroll Lock key twice:

[Scroll Lock] [Scroll Lock]

Auto Scan Mode

The CS-62A’s Auto Scan feature automatically switches the

KVM focus between the two computers at regular intervals so

that you can monitor their activity without having to take the

trouble of switching yourself. The default time interval is 5

seconds. To invoke Auto Scan Mode:

Press and release the Left Shift key; then press and release the

Right Shift key:

[Left Shift] [Right Shift]

Once scanning begins, it continues until you press the

[Spacebar] to exit Auto Scan Mode. The port that was currently

active at the time scanning stopped remains active.

Note: While Auto Scan Mode is in effect, ordinary keyboard

and mouse functions are suspended. You must exit Auto

Scan Mode by pressing the [Spacebar] in order to regain

normal control of their use.

- 7 -

2003-06-10

Changing the Scan Interval

Before you invoke Auto Scanning you can change the amount

of time Auto Scan dwells on each port. To do so, use the

following Hotkey combination.

[Left shift] [Right shift] [S] [n]

Where nrepresents a number from 1 to 4 that specifies the

desired scan interval time, as shown in the table below:

nScan Interval

[1] 3 secs

[2] 5 secs

[3] 10 secs

[4] 20 secs

Note: You must press and release the keys one at a time.

LED Display Table

Activity Indication

Off Port is not selected.

On (Steady) Port is connected to an active computer.

Flashing (On and Off equal) Port is connected to an active computer and is

being accessed in Auto Scan mode.

- 8 -

2003-06-10

Indice

Altri manuali ATEN Interruttore

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente