Atmel AT18F-DK3 Manuale utente

3685A–CNFG–04/08

Atmel AT18F-DK3 Configurator

Development Kit

....................................................................................................................

User Guide

AT18F-DK3 Configurator Development Kit User Guide i

3685A–CNFG–04/08

Table of Contents

Section 1

Introduction................................................................................................................. 1-1

1.1 Kit Content ......................................................................................................................... 1-1

1.2 Kit Features........................................................................................................................ 1-1

1.2.1 The ATF15xx-DK3 with ATF15xxDK3-SAX20..................................................... 1-1

1.2.2 JTAG ISP Download Cable ................................................................................. 1-2

1.2.3 JTAG Configurator Programming System (JCPS) Software ............................... 1-2

1.3 Supported Devices............................................................................................................. 1-2

1.4 System Requirements........................................................................................................ 1-2

1.5 Ordering Information .......................................................................................................... 1-2

1.6 JCPS References ..............................................................................................................1-3

1.7 Technical Support .............................................................................................................. 1-3

Section 2

Hardware Description................................................................................................. 2-1

2.1 The ATF15xx-DK3 Base Board ......................................................................................... 2-1

2.1.1 7-segment Displays with Selectable Jumpers ..................................................... 2-2

2.1.2 LEDs with Selectable Jumpers ............................................................................ 2-3

2.1.3 Push-button Switches with Selectable Jumpers for I/O Pins ............................... 2-4

2.1.4 Push-button Switches with Selectable Jumpers for GCLR and OE1 Pins........... 2-4

2.1.5 2 MHz Oscillator and Clock Selection Jumper..................................................... 2-5

2.1.6 VCCIO and VCCINT Voltage Selection Jumpers and LEDs ............................... 2-5

2.1.7 ICCIO and ICCINT Jumpers ................................................................................ 2-6

2.1.8 Voltage Regulators .............................................................................................. 2-6

2.1.9 Power Supply Switch and Power LED................................................................. 2-6

2.1.10 Power Supply Jack and Power Supply Header ................................................... 2-6

2.1.11 JTAG ISP Connector and TDO Selection Jumper............................................... 2-6

2.2 Socket Adapter Board...................................................................................................... 2-10

2.3 Atmel CPLD ISP Download Cable ................................................................................... 2-10

Section 3

Schematic Diagrams .................................................................................................. 3-1

AT18F-DK3 Configurator Development Kit User Guide 1-1

3685A–CNFG–04/08

Section 1

Introduction

The Atmel

AT18F-DK3 Configurator Development Kit is an In-System Programming (ISP) for the

AT18F Series of FPGA configuration memories (Configurators). This kit provides designers an easy way

to develop, prototype and evaluate new designs using the Atmel AT18F devices. The AT18F Series

JTAG ISP Configurator includes devices in four different densities – AT18F010-30XU (1M), AT18F002-

30XU (2M), AT18F040-30XU (4M), and AT18F080-30XU (7M). Since all of the devices in the AT18F

family are available in only one Green (Halide/Pb-free and RoHS Compliant) 20-lead TSSOP package

type, only one socket adapter board (ATF15xxDK3-SAX20) is needed to program the different AT18F

devices using the ATF15xx-DK3 Base Board and the Atmel JTAG ISP MV Rev 6.0 Cable

(ATDH1151VPC).

1.1 Kit Content

ATF15xx-DK3 Development Base Board

20-lead TSSOP Socket Adapter Board (ATF15xxDK3-SAX20)

An optional ISP Header Converter

One AT18F010-30XU and One ATF18F002-30XU Configurator Samples

A Quick Start Guide

An AT18F-DK3 Flyer

Note: JCPS Tutorial can be found from the Help menu of the software after installation.

1.2 Kit Features

1.2.1 The ATF15xx-DK3 with ATF15xxDK3-SAX20

10-lead JTAG-ISP Port

Regulated Power Supply Circuits for 9V DC Power Source

I/O Voltage Supply (VCCIO)

(1)

Core Voltage Supply (VCCINT)

(1)

20-lead TSSOP Socket Adapter Board (ATF15xxDK3-SAX20)

User I/O Pin Headers for All User I/O Pins of the ATF18 Series Configurators

2 MHz Crystal Oscillator

(2)

Four 7-segment LED Displays

(2)

Eight Individual LEDs

(2)

Eight Push-button Switches

(2)

Global Clear and Output Enable Push-button Switches

(2)

Current Measurement Jumpers

Introduction

1-2 AT18F-DK3 Configurator Development Kit User Guide

3685A–CNFG–04/08

Notes: 1. Both VCCIO and VCCINT must be set to 3.3V while programming the AT18F Series

devices. When changing the VCCIO or VCCINT jumper position, the power of the

ATF15xx-DK3 must be turned OFF.

2. These features are not intended to be used for the AT18F Series devices on this board.

They are intended to be used for the Atmel ATF15xx CPLDs when a different CPLD

Socket Adapter Board is used with the ATF15xx-DK3 Base Board.

1.2.2 JTAG ISP Download Cable

JTAG ISP Download Cable (Atmel JTAG ISP MV Cable V6.0) for PC Parallel Printer (LPT) Port

1.2.3 JTAG Configurator Programming System (JCPS) Software

Atmel JCPS software can be downloaded from Atmel web site at:

– http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4278

1.3 Supported Devices

The Atmel AT18F-DK3 Programming Kit supports the following device types.

AT18F010-30XU

AT18F002-30XU

AT18F040-30XU

AT18F080-30XU

1.4 System Requirements

The minimum hardware and software requirements to program an AT18F Series Configurators on the

AT18F-DK3 Programming Kit through the Atmel JTAG Configurator Programming System (JCPS) Soft-

ware are:

Pentium

or Pentium Compatible Microprocessor-based Computer

Windows XP,

Windows 98, Windows NT

4.0, or Windows

2000

64 Mbytes of RAM

200 Mbytes of Free Hard Disk Space

Windows Supported Mouse

Available Parallel Printer (LPT) Port

9V DC Power Supply with 500 mA of Supply Current

SVGA Monitor (800 x 600 Resolution)

1.5 Ordering Information

Part Number Description

ATF18F-DK3 Atmel AT18F Series Configurator Programming Kit

Introduction

AT18F-DK3 Configurator Development Kit User Guide 1-3

3685A–CNFG–04/08

1.6 JCPS References

Help Files – from the JCPS software main window, click on HELP and then select HELP FILE.

Tutorials – from the JCPS software main window, click on HELP, and then select JCPS TUTORIAL.

1.7 Technical Support

For technical support on any Atmel Configurator-related issue, please contact Atmel Configurator Appli-

cations Group at:

On-line Support Request Form:

http://www.atmel.com/dyn/products/support.asp

FAQs:

http://www.atmel.com/dyn/products/faq.asp?Faq=y

Product Web Site:

http://www.atmel.com/products/config/default.asp

AT18F-DK3 Configurator Development Kit User Guide 2-1

3685A–CNFG–04/08

Section 2

Hardware Description

2.1 The ATF15xx-DK3 Base Board

The ATF15xx-DK3 Base Board and the Socket Adapter Board are shown in Figure 2-1. They contain

simple features such as I/O headers that allow designers to easily use it when developing or evaluating

the ATF18 Series Configurator designs.

Figure 2-1. The ATF15xx-DK3 Base Board and the ATF15xxDK3-SAX20 Socket Adapter Board

Voltage

Regulators

GCLR

Switch

GOE

Switch

VCCIO

Selector

VCCINT Selector

VCCIO LED

VCCINT LED

Power LED

Clock Selector

Power Switch

Oscillator

Power Supply Jack

Power Supply Header

JTAG Cascade Jumper

JTAG ISP Header

7-segment

Displays

ATF15xxDK3-SAX20

Socket Adapter Board

Configuration

I/O Pin Headers

Device Socket

Push-button Switches

Push-button Jumpers

LEDsJumpers

LEDs

ICCINT Jumper

ICCIO Jumper

Hardware Description

2-2 AT18F-DK3 Configurator Development Kit User Guide

3685A–CNFG–04/08

2.1.1 7-segment Displays with Selectable Jumpers

The 7-segment Displays with Selectable Jumpers are available on the ATF15xx-DK3 Base Board of the

AT18F-DK3 kit. However, these components were designed for other Atmel adapter boards such us the

ATF15xx Series CPLDs, and they are not intended to be used with ATF15xxDK3-SAX20 socket adapter

for AT18F Series Configurators. Therefore, there is no detailed description about these components in

this user guide, if you need additional information, see the ATF15xx-DK3 Kit user guide.

The circuit schematic of the displays and the jumpers is shown in Figure 2-2.

Figure 2-2. Circuit Diagram of the Display LEDs and Jumpers

Hardware Description

AT18F-DK3 Configurator Development Kit User Guide 2-3

3685A–CNFG–04/08

2.1.2 LEDs with Selectable Jumpers

The LEDs with selectable jumpers are available on the ATF15xx-DK3 Base Board of the AT18F-DK3 kit.

However, these components were designed for other Atmel adapter boards such us the ATF15xx Series

CPLDs and they are not intended to be used with ATF15xxDK3-SAX20 socket adapter for AT18F Series

Configurators. Therefore, there is no detailed description about these components in this user guide, if

you need additional information, see the ATF15xx-DK3 Kit user guide.

Figure 2-3. Circuit Diagram of the LEDs and Jumpers

Hardware Description

2-4 AT18F-DK3 Configurator Development Kit User Guide

3685A–CNFG–04/08

2.1.3 Push-button Switches with Selectable Jumpers for I/O Pins

Eight push-button switches with selectable jumpers are shown on the ATF15xx-DK3 Base Board of the

AT18F-DK3 kit. However, these components were designed for other Atmel adapter boards such us the

ATF15xx Series CPLDs and they are not intended to be used with ATF15xxDK3-SAX20 socket adapter

for AT18F Series Configurators. Therefore, there is no detailed description about these components in

this user guide, if you need additional information, see the ATF15xx-DK3 Kit user guide.

Figure 2-4. Circuit Diagram of the Push-button Switches and Jumpers for the I/O Pins

2.1.4 Push-button Switches with Selectable Jumpers for GCLR and OE1 Pins

Two push-button switches for the Global Clear (GCLR) and Output Enable (OE1) with selectable jump-

ers are shown on the ATF15xx-DK3 Base Board of the AT18F-DK3 kit. However, these components

were designed for other Atmel adapter boards such us the ATF15xx Series CPLDs and they are not

intended to be use with ATF15xxDK3-SAX20 socket adapter for AT18F Series Configurators. Therefore,

there is no detailed description about these components in this user guide, if you need additional infor-

mation, see the ATF15xx-DK3 Kit user guide.

Figure 2-5. Circuit Diagram of Push-button Switches and Selectable Jumpers for GCLR and OE1

Hardware Description

AT18F-DK3 Configurator Development Kit User Guide 2-5

3685A–CNFG–04/08

2.1.5 2 MHz Oscillator and Clock Selection Jumper

The 2 MHz Oscillator and Clock Selection Jumper, JP-GCLK, are shown on the ATF15xx-DK3 Base

Board of the AT18F-DK3 Kit. However, these components are designed for other adapter boards to be

used with Atmel ATF15xx Series CPLDs, and they are not intended to use with ATF15xxDK3-SAX20

socket adapter for AT18F Series Configurators. Therefore, there is no detailed description about these

components in this document, but user can always reference ATF15xx-DK3 user guide for more

information.

Figure 2-6. Circuit Diagram of Oscillator and Clock Selection Jumper

2.1.6 VCCIO and VCCINT Voltage Selection Jumpers and LEDs

The VCCIO and VCCINT Voltage Selection Jumpers, labeled VCCIO Selector and VCCINT Selector,

respectively on ATF15xx-DK3 Base Board of the AT18F-DK3 kit are used to select voltage supply to the

device and to the JTAG connector. VCCIO voltage is used to set the I/O interface voltage (VCCO) and

JTAG programming voltage (VCCJ) of the AT18F Series Configurator. Also, VCCINT voltage jumper is

used to set the Core supply voltage of the AT18F Series device. When programming the AT18F Series

Configurator with the ATF15xxDK3-SAX20 adapter board, it is required to set both the VCCIO voltage

selector jumper and VCCINT voltage selection jumper to 3.3V.

Note: The power of the ATF15xx-DK3 Base Board MUST BE turned OFF when changing the

position of the VCCIO or VCCINT voltage selection jumper (VCCIO Selector or VCCINT

Selector).

Indice

Altri manuali Atmel Microcontrollore

Atmel

Atmel AVR32 STK1000 Manuale utente

Atmel

Atmel ARIS+ AT88SC-ADK2 Manuale utente

Atmel

Atmel AT91 Series Manuale utente

Atmel

Atmel AT43DK325 Manuale utente

Atmel

Atmel AT90S1200 Manuale utente

Atmel

Atmel ATmega32M1 Manuale utente

Atmel

Atmel AT91 Series Manuale utente

Atmel

Atmel ATmega8 Manuale utente

Atmel

Atmel AVR1019 Istruzioni per l'installazione e il funzionamento

Atmel

Atmel AVR 1908 Manuale utente

Atmel

Atmel ATmega128 Manuale utente

Atmel

Atmel AT88CK101BK8 Manuale di installazione

Atmel

Atmel AT89C52 Manuale utente

Atmel

Atmel 8051 Manuale utente

Atmel

Atmel ATAB5749 Istruzioni per l'installazione e il funzionamento

Atmel

Atmel ATSAMB11 BluSDK SMART Manuale utente

Atmel

Atmel AVR AVR350 Istruzioni per l'installazione e il funzionamento

Atmel

Atmel AVR2052 Manuale utente

Atmel

Atmel UC3 Series Manuale utente

Atmel

Atmel SAM L21 Xplained Pro Manuale utente

Atmel

Atmel SAM D09 Istruzioni per l'installazione e il funzionamento

Atmel

Atmel AVR128 Istruzioni per l'installazione e il funzionamento

Atmel

Atmel AT90USB162 Manuale utente

Atmel

Atmel ATBTLC1000 BluSDK Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente