Atmel STK521 Manuale utente
8194B–AVR–01/12
STK521
..............................................................................................
User Guide
STK521 User Guide 1-2
8194B–AVR–01/12
Table of Contents
Section 1 1
Introduction 1
Features 2
Section 2 3
Using the STK521 Top Module 3
Connecting the Atmel STK521 to the Atmel STK500 Starter Kit 3
Powering the STK521 4
Programming the AVR 5
Atmel AVR JTAGICE mkII Connector 7
Atmel STK521 switches configuration 9
Atmel STK521 headers 10
Atmel STK521 test points 11
Extra functions 11
Section 3 12
Troubleshooting Guide 12
Section 4 13
Technical Specifications 13
Section 5 14
Technical Support 14
Section 6 15
Complete Schematics 15
STK521 User Guide 1-1
8194B–AVR–01/12
Section 1
Introduction
The Atmel®AVR®STK®521 kit is made of the Atmel AVR STK521 board.
The STK521 board is a top module for the Atmel STK500 development board from Atmel Corporation. It
is designed to support the Atmel AT90PWM81, Atmel AT90PWM161 products and future compatible
derivatives.
The STK521 includes connectors and hardware allowing full utilization of the new features of the
AT90PWM81/161, while the Zero Insertion Force (ZIF) socket allows easy to use of SOIC20 package for
prototyping.
This user guide acts as a general getting started guide as well as a complete technical reference for
advanced users.
Note that in this guide, the word AVR is used to refer to the target components (AT90PWM81/161).
AT90PWM81 will be also used to refer to one of the products from this family.
Figure 1-1. STK521 Top Module for STK500.
STK521 User Guide 1-2
8194B–AVR–01/12
1.1 Features
Atmel AVR STK521 is a new member of the successful Atmel STK500 starter kit family
Supports the Atmel AT90PWM81, Atmel AT90PWM161
Supported by Atmel AVR Studio®4.15 or above and Atmel AVR Studio 5.1
Zero Insertion Force Socket for SOIC20 Package
Zero Insertion Force Socket for QFN32 Package (not populated)
High Voltage Parallel Programming
Serial Programming
6-pin Connector for On-chip Debugging using Atmel AVR JTAGICE mkII or Atmel AVR Dragon™
emulators
Switches for Reset/GPIOs configuration, Xtal/GPIOs or power supply configuration
External power supply connector for standalone mode
Quick Reference to all Jumpers in the Silk-Screen of the PCB
STK521 User Guide 2-3
8194B–AVR–01/12
Section 2
Using the STK521 Top Module
2.1 Connecting the Atmel STK521 to the Atmel STK500 Starter Kit
Connect the STK521 to the STK500 expansion header 0 and 1. It is important that the top module is con-
nected in the correct orientation as shown in Figure 2-1. The EXPAND0 written on the STK521 top
module should match the EXPAND0 written beside the expansion header on the STK500 board.
Figure 2-1. Connecting STK521 to the STK500 Board.
Note: Connecting the STK521 with wrong orientation may damage the board.
STK521 User Guide 2-4
8194B–AVR–01/12
2.1.1 Placing an Atmel AT90PWM81 on the Atmel STK521
The STK521 contains a ZIF socket for a SOIC20 package. Care should be taken so that the device is
mounted with the correct orientation. Figure 2-2 shows the location of pin1 for the ZIF socket.
Figure 2-2. Pin1 on ZIF Socket.
Caution: Do not mount an Atmel AT90PWM81 on the STK521 at the same time as an AVR is mounted
on the STK500 board. None of the devices might work as intended.
2.2 Powering the STK521
The STK521 can be powered as follows :
1. Through the STK500 by selecting POWER switch to VTG.
2. Through an external power supply using the jack connector and selecting POWER switch to
VEXT.
In this latter case, power supply must be 10V DC for a 5V device power supply.
PIN1
STK521 User Guide 2-5
8194B–AVR–01/12
2.3 Programming the AVR
The Atmel AT90PWM81 can be programmed using both serial SPI and high-voltage parallel program-
ming. This section will explain how to connect the programming cables to successfully use one of these
two modes. The Atmel AVR Studio STK500 software is used in the same way as for other AVR parts.
Note: The AT90PWM81 also supports Self Programming, see the Atmel AVR109 application note for
more information on this topic.
2.3.1 Serial in-system programming
Figure 2-3. Serial in-system programming.
To program the AT90PWM81 using ISP programming mode, connect the 6-wire cable between the
ISP6PIN connector on the Atmel STK500 board and the ISP connector on the Atmel STK521 board as
shown in Figure 2-3. The device can be programmed using the Serial Programming mode in the AVR
Studio 4 STK500 software.
STK521 User Guide 2-6
8194B–AVR–01/12
The Atmel STK500 and STK521 jumpers must be configured as follows :
Table 2-1. In-System programming jumper settings for the Atmel AT90PWM81.
Note: See the Atmel STK500 User Guide for information on how to use the STK500 front-end software
for ISP Programming.
2.3.2 High-voltage programming
Figure 2-4. High-voltage (parallel) programming.
STK500
VTARGET Mounted
AREF Open
RESET Open
XTAL1 Mounted
OSCSEL Mounted, pin 1 and 2
BSEL2 Open
PJUMP Open
STK521 User Guide 2-7
8194B–AVR–01/12
To program the AVR using high-voltage (parallel) programming, connect the PROG_CTRL of the Atmel
STK500 to PRG_CTRL of the Atmel STK521 and PROG_DATA of STK500 to PRG_DATA of STK521
as shown in Figure 2-4. Make sure that the CLOCK switch is placed in the STK500 position.
The STK500 and STK521 jumpers & switches must must be configured as follows :
Table 2-2. High-Voltage programming jumper settings for the Atmel AT90PWM81.
Table 2-3. High-voltage programming switches settings for AT90PWM81.
The device can now be programmed using the high-voltage programming mode in the Atmel AVR Studio
STK500 software.
Note: See the Atmel STK500 User Guide for information on how to use the STK500 front-end software
in high-voltage programming mode.
For the high-voltage programming mode to function correctly, the target voltage must be higher
than 4.5V.
2.4 Atmel AVR JTAGICE mkII Connector
See the following document :
“JTAGICE mkII Quick Start Guide” which purpose is “Connecting to a target board with the AVR
JTAGICE mkII”.
This note explains which signals are required for ISP and which signals are required for debugWIRE.
Figure 2-5 shows how to connect the Atmel AVR JTAGICE mkII probe on the STK521 board.
STK500
VTARGET Mounted
AREF Open
RESET Mounted
XTAL1 Mounted
OSCSEL Mounted, pin 1 and 2
BSEL2 Mounted
PJUMP Open
STK521
POWER VTG
CLOCK STK500
RESET RST/
STK521 User Guide 2-8
8194B–AVR–01/12
Figure 2-5. Connecting the Atmel AVR JTAGICE mkII to the Atmel STK521.
The ISP connector is used for the Atmel AT90PWM81 built-in debugWire interface. The pin out of the
connector is shown in Table 2-4 and is compliant with the pin out of the JTAG ICE available from Atmel.
Connecting a JTAGICE mkII to this connector allows on-chip debugging of the AT90PWM81.
More information about the JTAGICE mkII and on-chip debugging can be found in the Atmel AVR
JTAGICE mkII User Guide, which is available at the Atmel web site, www.atmel.com.
Note: Remove the RESET jumper on the Atmel STK500 to work run properly JTAGICE mkII.
Note: MISO, MOSI, and SCK lines can be disconnected when the product is in debugging mode. They
can then be used for application purpose.
Table 2-4. STK521 ISP/DW connector pinout.
Squid cable
colors Target pins STK521 ISP pinout Target pins
Squid cable
colors
grey MISO 1 2 VTG purple
black SCK 3 4 MOSI red
green RESET 5 6 GND brown
PIN1
Indice
Altri manuali Atmel Scheda madre
Atmel
Atmel AT73C224-EK1 Manuale utente
Atmel
Atmel Evaluation Board AT91SAM9XE-EK Manuale utente
Atmel
Atmel ATmega32HVB Manuale utente
Atmel
Atmel ATSAM4C-EK Manuale utente
Atmel
Atmel SAM3U-EK Manuale utente
Atmel
Atmel STK511 Manuale utente
Atmel
Atmel AT91EB63 Manuale utente
Atmel
Atmel AT90USB162 Manuale utente
Atmel
Atmel SAMA5D3 EK Series Manuale utente
Atmel
Atmel SAM L21 Xplained Pro Manuale utente
Atmel
Atmel ATDH2200E Manuale utente
Atmel
Atmel SAM4L8 Xplained Pro Manuale utente
Atmel
Atmel ATmega168 Manuale utente
Atmel
Atmel ATBTLC1000 Xplained Pro Manuale utente
Atmel
Atmel AT91EB01 Manuale utente
Atmel
Atmel ATMEGA256RFR2-ZUR Manuale utente
Atmel
Atmel ATSAMR30-XPRO Manuale utente
Atmel
Atmel AT91SAM7S-EK Manuale utente
Atmel
Atmel AT91SAM9263-EK Manuale utente
Atmel
Atmel AT91EB42 Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
