AUDAC OPT2 Manuale utente
OPT2
Installation Manual
www.audac.eu
2
Introduction
Matrix Fiber Interconnection module
The OPT2 is a fiber interconnection interface for the R2 and M2 Digital Multi-Zone &
Multi-Media Matrix Systems. This module makes it possible to transfer up to 16 digital
audio signals over one single fiber conductor (8 stereo channels) for covering large
distances.
Installation precautions
The installation of the display unit may only be performed by
qualified technicians.
Incorrect installation can lead to permanent damage or incorrect
functioning of the equipment.
Packaging contents
- OPT2 optical interface module
- 20p Flatcable
3
Instructions
Mounting and connecting
Step 1:
Make sure the M2/R2 power inlet is disconnected from the mains
power.
Step 2:
Open the M2/R2 housing by carefully removing the screws from the top panel of the
device.
Step 3:
Remove the Powersupply.
In case the unit has a powersupply mounted on a fixing plate, u better remove the
complete unit by removing the 4 screws from the bottom. Is the power supply not
mounted on a fixing plate, it is sufficient to remove the 5 screws from de L-shaped
PCA.
Fixing Plate
L-shaped PCA
4
.
Place the powersupply aside to make room for installing the OPT2 module.
Step 4:
Connect one side of the supplied flatcable to the connector P1 of the DSP board.
Note the correct polarity.
Pin 1
5
Step 5:
Connect the other side of the flatcable to the OPT2 module. In case there is a flatcable
supplied with 2 extra connectors, please use the connector nearest by the DSP!
Reassure the polarity of both connections!
Step 6:
Remove the nuts from the module, and place the module in the chassis.
Make sure to place the module in the right way. That is, with the connectors at the
side of the DSP. It might be necessary to move the suppression coil to the right to
make some space.
Suppression Coil
Pin 1
Pin 1
6
Step 7:
Fix the OPT2 board by tighten the nuts. Ensure not to over tighten the nuts.
Step 8:
Replace the Powersupply you removed in step 3.
7
Step 9:
Finally, place the OPT2 option label at the back of the unit at the designated place.
Step 10:
The OPT2 module is now properly installed. Close the housing, power up the system
and your M2/R2 matrix system including Optical fiber interface is ready for operation.
OPT2 option
14080306400001
S/N:14080306400001
Indice
Altri manuali AUDAC Unità di controllo
AUDAC
AUDAC ARJ12P Manuale utente
AUDAC
AUDAC NMP40 Manuale utente
AUDAC
AUDAC TRV106 Manuale di istruzioni
AUDAC
AUDAC SourceCon MMP40 Manuale utente
AUDAC
AUDAC APC100 MK2 Manuale utente
AUDAC
AUDAC SourceCon DMP42 Manuale utente
AUDAC
AUDAC WaveDynamics ANI Series Manuale utente
AUDAC
AUDAC EPA104 Manuale utente
AUDAC
AUDAC APC100 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
