Aumuller M-COM Click Manuale di formazione
!
!
Warranty claims require proper and profes-
sional assembly, installation and maintenance
in accordance with national regulations and
manufacturer‘s instructions of the drives.
The safety instructions in the supplied pro-
duct documentation are to be observed.
Strictly observe the information given in this
and in the instructions for installation of
drives when mounting the M-COM® Click.
Details can be found on our website
www.aumueller-gmbh.de
Keep this instruction over the lifetime of the
product.
M-COM®Click (Main control unit) 24V
• By using the M-COM® Click 6 single actuators (drives
or locks) are linked together in a multi-drive system.
• Whithin seconds, the M-COM® Click links and pro-
grammes the synchronized driverunnint mode and one
sequentce control, if additional locks are involved.
When using 2 locking drives, these run parallel.
• The LED display of the M-COM® Click signals the
successful initialization, the number of components
installed in the system and – if occurring – malfunctions.
• The use of standard drives in a drive system saves
storage costs.
• Subsequent installed or exchanged components can be
easily adressed and programmed.
Assembly and Commissioning Instructions
M-COM®Click
Rated voltage: 24V DC +/- 20%, (max. 2 Vss)
Current consumption: <12 mA
Control type: S12
Protection rating: IP30
Ambient temperature range: min. - 5 °C ... + 70 °C
Dimensions: 40 x 26 x 15 mm
Connection: for Aumüller chain drives
with AUMÜLLER-Click plug solution.
Feature: able to congurate drive parameters by simple
plug-on into the single or last drive of the
multi-drive system.
Suitable for 24V- or 230V-drives, but it can only
be used on the 24V-side.
Equipment: Tongs for removing the M-COM® Click.
Part.-No.: 524167
Application: Communication module for automatic conguration and
surveillance of max. 4 opening and 2 locking drives version S12 / S3 (software
version SW-V2) in synchronised multi-drive systems.
Assembly Instruction
M-COM®Click
COMMISSIONING / TEST RUN
INSTALLATION STEP 1: FIRST COMMISSIONING
INSTALLATION STEP 2:
TEST RUN, MALFUNCTION, TROUBLSHOOTING
¢Switch on the supply voltage - in CLOSE direction.
¢Observe the LED reaction of the M-COM®Click.
¢Insert M-COM®Click Œin the drive.
¢Switch on the supply voltage - in CLOSE direction.
¢Observe the LED reaction of the M-COM®Click Œ.
¢LED blinks red (Factory settings).
¢LED starts blinking red / green. The communication
- to the multi-drive operation - is running.
¢LED blinks green, for each participator once. The pro-
cess is complete.
¢Compare the numer of devices with the numer of
identied participants.
¢Check the operation of the multi-drive system according
the instructions for installation the drives.
TROUBLSHOOTING: LED blinks red.
¢Check wiring and the system.
¢Eliminate faults.
¢Reset the M-COM®Click (see chapter „Reset and re-
initialisation of M-COM®Click)“.
Series connection with M-COM®Click
DRIVE
M-COM®Click
NOTE
To install the M-COM®Click Œcorrectly,
note the screws •of the drive and of the
M-COM®Click Œ.
Turn the M-COM®Click Œand the drive so,
that the screws •are visible above.
1
2
LED
Screws •of the drive in the upper area
Screws •of the M-COM® Click are visible above
2
LED display
Display State
3s
lights red
Factory settings
(M-COM®Click is reset).
0,5s - 0,5s
blinks red / green (10 times)
Communication - to the multi-drive
operation - becomes set up.
0,5s - 0,5s - 3s
blinks green (X times)
X drives identied
(1 time blinks = identied one drive).
LED display
Display State
0,5s - 0,5s - 3s
blinks green (per drive 1 time)
System is o.k. (can be operated)
drives identied
(1 time blinks = identied one drive).
0,5s - 0,5s - 3s
blinks red (X-times)
When the number of the
learned drives does not coin-
cide with the number of drives
now recognized.
FAULT: System is NOT o.k.
X drives identied
(1 time blinks = identied one drive).
< <<
Assembly Instruction
M-COM®Click
RESET / DEMOUNTING
RESET AND REINITIALISATION OF M-COM®
Click
¢To reset the system: press the pushbutton within the
drilling •for about 5 seconds - using a wire (max.
Ø 1mm). The supply voltage is applied.
¢The LED starts blinking red and lights after successful
reset permanently red.
¢The factory setting is reached, the learning process will
automatically restart.
DEMOUNTING THE M-COM®CLICK
IN CASE EXCHANGING AFAULTY DRIVE
In case of exchange a faulty drive, demout and reset the
M-COM®Click.
¢Switch off the supply voltage.
¢Disconnect the connection cable from the faulty drive.
¢Demount the faulty drive.
¢Remove the M-COM®Click Œfrom the drive.
Squeezing the locking hooks at the M-COM®Click Œ
and pulled out the M-COM®Click Œfrom the drive
- using the tongs Ž.
¢Mount the new / repaired drive and connect it.
¢M-COM®Click Œin den Antrieb einstecken.
¢Switch on the supply voltage - in CLOSE direction.
¢Reset the M-COM®Click (see chapter „Reset and re-
initialisation of M-COM®Click)“.
¢Disposing of faulty equipment according to the instal-
lation instructions of drives.
DRIVE
NOTE The tongs Žis included in the scope of
delivery of M-COM®Click.
1 3
squeeze both locking hook
3
LED display
Display State
0,5s - 0,5s
blinks red (6 times)
M-COM®Click is waiting.
continuous
lights red
M-COM®Click is reset
(Factory settings).
DRIVE M-COM®Click
1
4
wire max. ø1 mm
14 mm immersion depth
AUMÜLLER AUMATIC GMBH
Gemeindewald 11
86672 Thierhaupten
Tel. +49 8271 8185-0
Fax
+49 8271 8185-250
info@aumueller-gmbh.de
www.aumueller-gmbh.de
AUMÜLLER AUMATIC GMBH
Gemeindewald 11
86672 Thierhaupten
Tel. +49 8271 8185-0
Fax
+49 8271 8185-250
info@aumueller-gmbh.de
9000021701_V0.1_KW20/16
TROUBLSHOOTING
TROUBLSHOOTING:
Exchanging a faulty drive in the multi-drive
system:
TROUBLSHOOTING:
M-COM®Click take off under voltage:
¢Switch off the supply voltage.
¢Disconnect the connection cable from the faulty drive.
¢Demount the faulty drive.
¢Mount the new / repaired drive and connect it.
¢Switch on the supply voltage - in CLOSE direction.
¢Reset the M-COM®Click (see chapter „Reset and re-
initialisation of M-COM®Click)“.
No adjustment is carried out in case of ex-
change of drives with special program-
ming (e.g. stroke, speed)!
In case of repair please order an exchange drive with the
same parameter assignment as that of the faulty drive.
If the M-COM®Click is removed under voltage and the
drives move, then the drives stop immediately.
¢Insert M-COM®Click again into the drive.
¢Put the system back into operation.
!
4
Altri manuali Aumuller Unità di controllo
Aumuller
Aumuller SHEV EMB 8000+ Series Manuale di installazione e funzionamento
Aumuller
Aumuller EMB 7300 Manuale di installazione e funzionamento
Aumuller
Aumuller USKM Manuale di formazione
Aumuller
Aumuller M-COM Click Manuale di formazione
Aumuller
Aumuller SHEV EMB 8000+ Series Manuale di installazione e funzionamento
Aumuller
Aumuller EMB 7300 Series Manuale di installazione e funzionamento
Aumuller
Aumuller M-COM Manuale di formazione
Aumuller
Aumuller LZ1-2,5A-KNX Manuale di installazione e funzionamento
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
