AURATON 2005 Manuale utente
2005 TX RX Plus
2005
user manual en
I
0
AURATON 2005
AURATON
2005 TX Plus
Communication code of AURATON 2005 TX Plus
can be manually set by user.
The factory set communication code is "085".
If there are troubles with communication between
AURATON 2005 TX Plus and RX Plus the code can
be changed (Manual, page 41).
AURATON
2005 RX Plus
29 EN
1. Installation instructions
AURATON 2005
Caution: Switch off the electric source before
installing the thermostat. We recommend that the
installation should be performed by a trained
personnel.
1.1 Select a suitable location for the AURATON
2005.
The location of the thermostat can greatly affect its
performance. If it is located at where circulate air
cannot reach, or exposed to direct sun light, it will
not adjust the room temperature properly.
To ensure proper operation, the thermostat should
be installed at an inside wall with freely circulating
air. Find a place where your family usually
occupied.
.
Avoid close to some heat generating appliance (e.g.
TV, heater, refrigerator) or exposed to direct sun
light. Do not install near a door where the
thermostat will suffer from vibration.
150cm
właściwe usytuowanie sterownika
PROPERLY INSTALLED THERMOSTAT
AURATON 2005
AURATON 2005 - Installation 30
EN
1.2 Wiring AURATON 2005
Wiring terminals are at the back of the thermostat.
Press down the terminal cover, you can find three
terminals which labelled COM, NO and NC. It is a
typical single-pole, double throw (SPDT) contact. In
most COM and NO are used.
1.3 Mounting the thermostat AURATON 2005
Use the template provided, drill two Ø6mm holes on
the wall. Insert the wall anchors and tighten the left
screw with 3mm clearance.
NO
COM
NC
NO
COM
NC
Fix the thermostat by putting it over the screwhead
and slide it rightward (note the keyhole like opening
at the back of the thermostat). Tighten the remain
screw to lock it in place.
Note:
If the wall is made of wood, there is no need to use the
wall anchors. Drill two Ø2.7mm holes instead of
Ø6mm.
AURATON 2005 - Installation
31 EN
2. Familiar with your
AURATON 2005
AURATON 2005 TX Plus
2.1 Appearance
There is a sliding front cover at the right of the
thermostat. If you open the cover, you can see
some buttons. This cover is removable for the
replacement of batteries. To rise up the sliding
cover, you can see the dip switch.
PROG
0612 18 24
0
c
dnm
Temp.
Prog.
Prog.#
OK Reset
-
-
+
+
ON
123
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON 32
2.2 Temperature mode
You can see "A" and "B" on both the buttons
and the LCD. "A" indicates comfort temperature
and "B" indicates economy temperature. These two
temperatures are user changeable. Furthermore,
O
there is a fixed defrost temperature (7 C) indicated
by "d" on the LCD. Throughout the operation of
the thermostat we will refer them as comfort,
economy or defrost temperature instead of numeric
values.
2.3 Dip switches
ON
123
DELAY 5 MIN.
COOLING
HEATING
NO DELAY
O
SPAN TEMP = 1 C
SPAN TEMP
O
= 0,5 C
EN
If you remove the front cover, you can find three
small switches (dip switches). These three switches
are used to control the span, output-on delay and
O
heat/cool system. Span is the temperature (1 C or
O
0,5 C) difference between the turn on temperature
and turn off temperature.
2.4 Program
AURATON 2005 or AURATON 2005 TX Plus is a
programmable thermostat. It can automatically
adjust the room temperature to a comfortable level
when you are at home, and lower it to save energy
when you go out or sleep. What you have to do is
to program the thermostat so that it knows when to
raise the temperature. There are altogether nine
programs contained in the memory of the
thermostat. Six of them are preset in the factory and
the remaining three are user changeable.
2.5 LCD
1 - Day of the week Indicator
2 - Time
3 - Temperature
4 - Program Number
5 - Program Profile Indicator
6 - Manual Override Indicator
7 - Output-On Indicator and temperature Mode
Indicator
8 - Low Battery Indicator
0
c
PROG
0612 18 24
1
2
8
5
4
6
7
3
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON
33 EN
Note:
A. The output-on indicator will be displayed if the
output is on. It will disappear if the output is off.
B. The low battery indicator will be displayed if the
voltage of the batteries drop to a certain level.
Please change the batteries as soon as
possible.
2.6 Start
The thermostat is operated by two LR6 alkaline
batteries. Please remove the front cover and install
two new batteries. When the batteries are installed,
the thermostat should be operating and you can
see the LCD active. If the thermostat does not work
properly, please check the batteries for wrong
polarities and press the reset button by a ball-point
pen.
The LCD after start or reset.
Note:
O
A. Temperature may not be 22.25 C as the
diagram shown and the Output-On indicator
may active after a few seconds, depend on
different situations.
B. Do not use a pencil to push the reset button.
The graphite residue of a pencil can cause
short circuit and damage the thermostat.
34
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON
0
c
PROG
0612 18 24
..
EN
2.7 Set day/time
To set day, press "d" button. Similarly, press "h"
button to set hour and "m" button to set minute.
Example: When start or after reset, the time is
00:00, Sunday. To set the clock to current time (e.g.,
11:23, Tuesday), press "d" 2 times, "h" 11 times and
"m" 23 times.
Note: When you press and hold the keys for 2
seconds the day/time will change rapidly. Release
when the desired setting comes.
2.8 View/Change temperature
Press Temp, the thermostat enter View/Change
temperature mode. The LCD will show the setting of
the current temperature mode ( A, B or d ) which
will be flashing. Press button "A" or "B" button to
review or change the temperature. Press OK will
directly return to normal operation mode.
Note:
O
A. The temperature setting range is 5 to 30 C.
B. To lower the setting, enter View/Change
temperature mode and press "A" or "B" until it
O
reaches 30 C and then the setting will return to
O
5 C. Continue to press until the desired setting
comes.
C. Press and hold the keys, the setting will change
rapidly.
D. Please note the temperature mode indicator. A
"A" means the comfort temperature is being
viewed or changed.
A "B" indicates economy temperature. If "d" is
shown, it is defrost temperature. Defrost
O
temperature is always at 7 C and is not
changeable.
E. It is not always necessary to use OK key to
return to normal operation mode. After 15
seconds of no key pressed it will automatically
return to normal mode.
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON
35 EN
2.9 View/Change programs
Press "Prog" button, the program of the current day
is ready to be changed.
Press "Prog" button again can advance to the next
day and the program of that day will be shown.
Press "Prog#" button to change the program.
Programs 6, 7 and 8 are user-define programs. You
can use "A" or "B" to change the distribution of
comfort or economy temperature and h to review
the setting. Press OK can return to normal
operation mode.
There are altogether nine programs available, as
the diagram shown: Program 0 is a special program. It will set the whole
O
day to defrost temperature (7 C). (If cooling mode is
selected, it will turn off the system). Programs 1,2,
and 3 are some typical schedule of a day. You can
select them if you found them suitable. Program 4
set the whole day to comfort temperature while
program 5 set it to economy. Programs 6, 7 and 8
are user-define programs. They can be modified to
suit your need.
36
0612 18 24
0612 18 24
0612 18 24
PROG
PROG
PROG
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON
0612 18 24
0612 18 24
0612 18 24
0612 18 24
0612 18 24
PROG
PROG
PROG
PROG
PROG
PROG
0612 18 24
EN
Example:
A. Assume you want to assign program 6 to
Saturday and want to set the whole day to
economy temperature except 13:00 to 18:00.
Press "Prog". The thermostat enters program
mode and the program of the current day (e.g.,
Tuesday) is ready to be programmed. The
display shows the program for Tuesday is
program 1, the temperature for 00:00 is
O
economy temperature and is 15 C. (The
flashing cursor is the time to be edited)
B. Press "Prog" 4 times. The day indicator will
point to Saturday:
C. Press "Prog#" 5 times to change the program
from program 1 to program 6
D. Now you can set the time shown to economy
temperature by pressing "B" or press "A" to set
it to comfort temperature. Or you can use "h"
key to pass through the time without changing
the setting.
Since we want to set 13:00 to 18:00 to comfort
temperature and the remains to economy
temperature, press 13 times. 00:00 to 12:00 will
be programmed to economy temperature
Press "h" or "A" 6 times to move the flashing
point to 19:00:
E. Finally, press "B" 5 times to set the remains of
the day to economy temperature:
0
c
0612 18 24
..
0612 18 24
..
AURATON 2005, AURATON 2005 TX Plus - Familiar with your AURATON
37 EN
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali AURATON Termostato
AURATON
AURATON S03 RTH Manuale utente
AURATON
AURATON 200 RTH Manuale utente
AURATON
AURATON Tucana Manuale utente
AURATON
AURATON 3003 Manuale utente
AURATON
AURATON 2100 TX Manuale utente
AURATON
AURATON 2020 Manuale utente
AURATON
AURATON T-1 RT Manuale utente
AURATON
AURATON Libra Manuale utente
AURATON
AURATON R30 RT Manuale utente
AURATON
AURATON 2005 TX Manuale utente
