AutoConnect AC202 Manuale utente

Thank-you for your purchase!

You’ve made the decision to have full control of

your vehicle. Follow the steps below to begin a

new era of vehicle controls.

Visit our website and click on the “Activate” tab,2.

Ensure you have the Serial # for your device.

Once submitted you will receive a confirmation

email from Northsat Distribution with the details

of your device activation.

and fully complete form

3. Select YOUR model number (device type) and

When installing an Autoconnect device you

must first determine the installation type.

The following pages will help you determine

the type and instructions for installation.

Choose the proper communication Protocol

depending on installation type before sending any

test command

QUICK START GUIDE INSTALLER PORTAL

DETERMINE INSTALLATION TYPE

Choose proper installation location ensuring to

follow instructions on install guide

Determine with customer if installation is to be

stealth (not visible)

Have label facing the sky and clear from any

metal above it.

Actual location will vary by vehicle year, make

and model.

2INSTALL YOUR AUTOCONNECT

GPS MODEM

TEST THE DEVICE FUNCTIONS

Click on the Login link at the top

of any page of the autoconnectgps.com website

or download the free App for your mobile device.

Each Device comes with “TEST DATA” for you

to test all functions. This data will expire a few

days after installation.

Use the SID# for USERNAME and PASSWORD.

TIP

WE RECOMMEND AFFIXING THE SID STICKER

TO THE DOOR JAMB OF THE VEHICLE

TIP

autoconnectgps.com1 855 287 4477

Start, Lock, Unlock, open your trunk (*AC202 Only)

Know the vital statistics of your vehicle(s)

Request a vehicle(s) Location On-Demand

Monitor vehicle(s) for Aggressive Driving and Excessive Idling

Know where your vehicle(s) went, and how they got there

TAKE CONTROL OF YOUR VEHICLES LIKE

NEVER BEFORE!

ON ALL MAJOR PLATFORMS

REV100220

Username

Password

QUICK INSTALL GUIDE

For Live Tech Support:

Call Certified Tracking Solutions at 1-780-391-3800.

Toll Free 1-855-287-4477(CTS-4GPS)

Mondayto Friday8AM to 5PM MST

AutoConnectGPS.com

Determine Installation Type and Options

Attention: This modem is shipped temporarily pre-activated for the installer to send up to 50 test commands

before having to send in the activation form.

STEP 1:

Complete the wire connections according to the selected Installation Type.

STEP 2:

Depending upon your requirements, the AC202 module can be installed in a variety of ways.

Type 1 – Standalone GPS Tracking

Type 2 – Solace / Titan Elite Remote Starter

Type 3 – Fortin EVO-ALL (Standalone FW)

Type 4 – Fortin EVO-ONE

Type 5 – ADS AL-CA (Standalone FW)

Please see the following pages for detailed instructions and wiring diagrams.

Failure to adhere to these suggestions will result in a weak cellular and/or GPS signal and will affect

the performance of the device.

- Secure in upper portion of dash in a hidden location with correct side pointing

skyward .(label will indicate proper orientation)

- Do not cover with metal or position near any source of interference (Vehicle Radio, BCM). Keep a

safe distance of at least 24”.

Yellow: 2 Flashes / Second Connected / Online

Green: 1 Flash / Second Valid GPS

Each AC202 device is shipped pre-activated for the installer to send up to 50 test

commands before having to complete the online activation form. It is HIGHLY recommended that

you follow one of the test procedures below to ensure proper functionality. Alternatively you can

call Certified Tracking Solutions and we will perform the test with you.

Confirm LED Status

STEP 4:

Confirm Vehicle Connectivity and GPS location

STEP 5:

Position the AC202 Module in an Optimal Location

STEP 3:

Type 6 – ADS iDatastart (Classic, BM&BZ, VWx, HCx)

Type 7 – DEI (DBALL2/3, 4x10 / 5x10)

Type 8 – DEI (REMOTE STARTERS with ESP2)

Type 9 – Mid City (SKSNxxx)

AC202

A: via the AutoConnect website B: via the AutoConnect Smartphone App

a) Go to www.AutoconnectGPS.com and

click on “ Customer Login”

b) Enter the AC202’s Serial# (ESN)

for both the User Name and password.

c) Click Login.

The AutoConnect website dashboard

should load and display the Serial number

of the AC202 device that you are

installing.

a) Download the AutoConnect Smart-

phone app by searching “Autoconnect

GPS” for iPhone, Android or Blackberry

b) Open App and click on “Config ” then

“Login”

c) Enter the AC202’s Serial# (ESN)

for both the User Name and password.

d) Click “Save”

1) Login to view and test the AC202 device

Test procedure

A: via the AutoConnect website B: via the AutoConnect Smartphone App

2) Test Vehicle GPS Connectivity

a) Click on device serial # on the left side

of the screen. The asset info box will open

on the bottom left corner of the screen.

b) Click on the “Asset Commands & Con-

trols” icon located at the top of the Asset

Info box*

a) Click on the “GPS” tab

b) Click on the “Bullseye” button at top left

of screen

The successful completion of this section will enable you to see the current position of the

AC202 device on the dashboard/Smartphone map.

pg 2

*if using Type 2 to Type9 please ensure you

have selected appropriate data protocol

QUICK INSTALL GUIDE

AC202

INSTALLATION TYPE 1

AC202

pg 3

Standalone GPS Tracking

Installation Steps

Programming and Testing

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Yellow/Black

Yellow/Brown

Blue/Green

Green

Fuse

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

1. Install AC202 as per diagram above.

2. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

3. Install hardwired ignition recommended for this type of install

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of the dashboard

4. Test GPS Tracking functions

5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

pg 4

Solace / Titan Elite Remote Starter

Installation Steps

Programming and Testing

INSTALLATION TYPE 2

AC202

1. Ensure you have swapped the blue and white wire on connector

2. Complete installation of Remote Starter (R.S.) including programming the bypass module in the appropriate

DATA protocol *For Fortin modules you must switch the protocol using the Flashlink Manager. Turn option

F2 AP/OFA to “ON”. If you do not have a Flashlink Manager you must hardwire all connections between the bypass

module and R.S.

3. Program R.S. for M2-11-1(iDatalink 2-way) for Fortin and iDatalink modules.

4. Connect the 2 RF Conn 1, one to the Bypass Module and the other one to the IC4. You will need the extension

cable “Starter Connection Cable” available from CTS Tracking.

5. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

6. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the

vehicle.*DO NOT CUT THE DATALINK CABLE

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Scroll to the bottom of the commands and send the required Installer Protocol.

5. For iDatalink and Fortin Modules select “Set Telematic Protocol”. This option is by default

6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Swap Blue with

white at

the connector

Fuse

Bypass Module:

iDatalink

Fortin

*Use iDatalink 2-Way Protocol

RF CONN 1

RF CONN 2

RF CONN 3

IC4

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Swap Blue with

white at

the connector

Starter

Connection

Cable

pg 5

Fortin EVO-ALL (Standalone FW)

Installation Steps

Programming and Testing

INSTALLATION TYPE 3

AC202

1. Program EVO-ALL as per Fortin installation instructions for vehicle. (Ensuring to select option H2 in Flashlink Manager) or

visit http://fortin.ca/download/20101/autoconnect_evo-all.pdf

2. Complete installation as per Fortin installation diagram including the programming of the bypass module.

3. Connect Data link cable to the Bypass Module. You will need the extension cable “Starter Connection Cable” available from CTS

Tracking.

4. Powering the AC202 module and Bypass module

5. Scroll to the bottom of the commands and send the required Installer Protocol.

6. For Fortin EVO-ALL select “Set Fortin Protocol”.

7. Program the Autoconnect to Fortin module by performing the following:

-Hold programming button while inserting datalink cable to EVO-ALL. Release button when Blue & Red LED’s Turn on

-Press & hold the programming button on the EVO-ALL (The LED’s will turn off then back on approx 5 seconds), release button

-Turn Ignition ON (ALL 3 LED’s should be on now)

-Send the Lock command from the Autoconnect. The Blue and Red LED’s should flash once. | Turn Ignition OFF

8. Mount the Autoconnect module as described in Autoconnect Install.

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Fuse

Bypass Module:

iDatalink

Fortin

*Use iDatalink 2-Way Protocol

RF CONN 1

RF CONN 2

RF CONN 3

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Starter

Connection

Cable

1. Program EVO-ONE as per Fortin installation instructions for vehicle (Ensuring to select option H2 in Flashlink Manager) or visit

http://fortin.ca/download/26701/autoconnect_evo-one.pdf

2. Complete installation as per Fortin installation diagram.

3. Connect Data link cable to the Bypass Module. You will need the extension cable “Starter Connection Cable” available from CTS

Tracking.

4. Connect Power, Ground and Ignition from AC202 if you want to use true voltage.

5. Scroll to the bottom of the commands and send the required Installer Protocol.

6. For Fortin EVO-ONE select “Set Fortin Protocol”.

7. Program the Autoconnect to Fortin module by performing the following:

-Turn Ignition On.

-Press and hold the Valet switch until LED flashes then release. Then press Valet switch 5x.

-Press and release the brake pedal.

-Send the Lock command from the Autoconnect. The park lights will flash once to confirm.

-Press and release the brake pedal then turn igntion OFF.

8. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

pg 6

Fortin EVO-ONE

Installation Steps

Programming and Testing

INSTALLATION TYPE 4

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Fuse

RF CONN 3

RF CONN 1

RF CONN 2

RF CONN

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Starter

Connection

Cable

1. Program ADS-AL-CA as per iDatalink instrucitons for vehicle using a Weblink cable and choose Drone Telematics Kit.

2. Complete installation as per iDatalink installation diagram.

3. Connect Data link cable to the Bypass Module. You will need the extension cable “Starter Connection Cable” available from CTS

Tracking.

4. Connect Power, Ground and Ignition from AC202 if you want to use true voltage.

5. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.

*DO NOT CUT THE DATALINK CABLE

6. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Scroll to the bottom of the commands and send the required Installer Protocol.

5. For ADS-AL-CA select “Set ADS Protocol”.

6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

pg 7

ADS AL-CA (Standalone FW)

Installation Steps

Programming and Testing

INSTALLATION TYPE 5

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Fuse

RF CONN 3

RF CONN 1

RF CONN 2

RF CONN

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Starter

Connection

Cable

1. Ensure you have swapped the blue and white wire on connector

2. Program iDATASTART as per iDatalink instrucitons for vehicle using a Weblink cable and choose Drone Telematics Kit.

3. Complete installation as per iDatalink installation diagram.

4. Connect Data link cable to the Bypass Module. You will need the extension cable “Starter Connection Cable” available from CTS

Tracking.

5. Connect Power, Ground and Ignition from AC202 if you want to use true voltage.

6. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Scroll to the bottom of the commands and send the required Installer Protocol.

5. For iDatastart Modules select “Set Telematic Protocol”.

6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

pg 8

ADS iDatastart (Classic, BM&BZ,VWx, HCx)

Installation Steps

Programming and Testing

INSTALLATION TYPE 6

AC202

TELEMATICS

PORT

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Fuse

RF CONN 3

RF CONN 1

RF CONN 2

RF CONN1

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Starter

Connection

Cable

Swap Blue with

white at

the connector

1. Program DEI Module as per installation instructions for vehicle (Ensure to have the SMART START Option ENABLED)

2. Complete installation as per installation diagram.

3. Connect Data link cable to the Bypass Module. You will need the extension cable “Starter Connection Cable” available from CTS

Tracking.

3b. Connect Power, Ground and Ignition. Ignition must be connected

4. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

1. Open the Autoconnect App or Dashboard

2. Log in to the Autoconnect device installed using the SID # as both username and password.

3. Go to the command tab on the bottom of the app, or the remote function of dashboard

4. Scroll to the bottom of the commands and send the required Installer Protocol.

5. For DEI Modules select “Set D2D Protocol”.

6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).

7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

pg 9

DEI (DBALL2/3, 4x10 / 5x10)

Installation Steps

Programming and Testing

D2D PORT

INSTALLATION TYPE 7

AC202

White - Key Ignition Source (+)

Red 12V +

Black Ground

Fuse

RF CONN 3

RF CONN 1

RF CONN 2

RF CONN1

Yellow/Black: Input 1 (Optional (-), Can be used for hardwired alarm)

Yellow/Brown: Input 2 (Optional (-))

Blue/Green: Output 1 (Optional (-))

Green: Output 2 (Starterkill (-))

External Connector: Not used

Starter

Connection

Cable

Indice

Altri manuali AutoConnect Unità di controllo

AutoConnect

AutoConnect AC100GPS3G Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente