Avery Dennison Monarch 9485 Manuale utente

All specifications are subject to change without notice

USER MANUAL

TC9485UM Rev. AE 04/14

Table of Contents

Unpacking

2. Product overview 3

3. Installation & Usage 4

3-1. Display 4

3-2. Installing the Battery 5

3-3. Removing the Battery 6

3-4. Charging the Battery 7

3-5. Installing Belt Clip 8

3-6. Stock Installation 9

3-7. Peel Mode 10

3-8. Shoulder Strap Installation 11

3-9. Diagnostic Test 12

4. Peripherals Connection 14

4-1. Wireless Communication 14

4-2. Interface Cable Connection 15

5. Printer Cleaning 16

5-1. PrintHead Cleaning 16

5-2. Platen Roller Cleaning 17

6. Pritner Specication 18

6-1. Specication 18

7. CPCL Command Compatibilit

8. ZPL Command Compatibilit

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION

1. Unpacking

Stock

Shoulder Strap

SHOULDER

STRAP RING

Printer Battery Belt Clip

Recharger

Optional

Standard

2. Product overview

CHARGER

CONNECTOR

COVER OPEN

BUTTON

Front

Bottom

USB Cable

Quick Reference

Serial cable

PEELER BODY

PEELER WING

BATTERY

DOOR

BELT CLIP

CONNECTOR

SERIAL

USB

DISPLAY

Button Name function

Paper Feed/

Down button

Advances the supply. Clears error message.

Moves down through menu options.

Enter button

Selects the highlighted menu option.

Up button

Moves up through menu options.

Power button

Turns the printer on and o. Press to turn power

on. Press for three seconds to turn power o.

Wakes the printer from sleep mode.

3-2. Installing the Battery

NOTE

3-1. Display

3. Setting Up the Product

Remove the battery door. Insert the battery as shown.

Replace the battery door.

You must fully charge the battery when you receive the printer.

Batteries can be charged in the printer or in an optional external cradle

1. The battery status LEDs indicate amount of power remaining. Actual run-time

remaining depends on factors such as the contents of output,

distance to computer, etc.

2. When the battery level is very low, high density printing can result in the printer

switching o during printing resulting in possible loss of data.

3-4. Charging the Battery

1. Turn o the printer.

2. Be sure that the AC plug is correct.

If AC plug is wrong, change the plug to the correct one.

3. Open the DC jack by pulling on the rubber cover and insert DC jack into

the printer.

4. Plug the AC plug into an electrical outlet.

5. The charge indicator LED (located on the AC charger as shown) shows red

or green according to the status.

3-3. Removing the Battery

3-4-1 The status of lamp in charging

Status charging charging complete

Charging Lamp Red

Green

Remove the battery door. Lift out the battery.

②

①

LED

If there is trouble while charging the battery, the charge indicator LED blinks green.

Try unplugging and reconnecting charger, charging should resume.

Charging is complete when the LED changes to solid green.

NOTE

Use two hands to close the cover until it

clicks into place. Press the feed button.

The belt clip is included with the printer but is not required to be used or installed!

3-5. Belt clip Usage

Insert screw into belt clip.

Tighten the screw with driver as shown.

NOTE

3-6. Stock Installation

1 2

Put the stock in so it unrolls from the

bottom. Remove the stock core when

it is empty. Pull a short length of stock

out of the printer.

Open the Paper cover by pressing the

Open button and set the width of paper

guide by turning the knob with nger.

Adjust the width of paper guide if

needed.

10 11

3-7. Peel Mode

1 2

With a roll of stock installed, slide the

peeler body towards the back of the

printer.

Lift the peeler wing and slide the peeler

body towards the front of the printer.

Press the feed button.

Push the peeler body until you see two

complete triangles. Press the feed button.

Peel Mode

Non-Peel Mode

Insert the strap into the hook of the printer.

Place the end of the strap into

the hook of shoulder strap.

After pulling out the end of the

strap tightly, put it into the clip

to be fastened.

Optional

3-8. Shoulder Strap Installation

12 13

3-9. Diagnostic Test

1 2

NOTE

Turn o the printer.

The information label prints.

Press and hold the feed

button and power button.

1. For Hex Dump mode, do steps 1-2 then

press the feed button.

2. After printing ASCII pattern,

the diagnostic test is complete.

3. If the feed button is not pressed to go to

Hex Dump mode, the printer exits

diagnostics after three seconds.

The sample of self test printout

Upon initial installation or for troubleshooting, you can run the diagnostic test to get

information about:

Firmware version, emulation, codepage, sensor settings, interface settings, etc.

If no issues are found with diagnostic test, examine other devices and software.

The diagnostic test is working independent of devices and software.

●Do not overheat the motor

To prevent the motor from overheating, stop the printer for at least 30 seconds

after continuously printing 1.5 meters.

14 15

4. Peripherals Connection

This product can communicate with other devices using Bluetooth, WiFi

(802.11b/g), or a USB/Serial cable.

1. Printer can connect to a PDA or PC for wireless communication.

2. Your PC must support Bluetooth or WiFi (802.11b/g) to connect to the printer.

4-1. Wireless Communication

NOTE

Refer to the System Administrator Guide for more information.

4-2. Interface Cable Connection

1. Connect the USB or Serial cable to the cable connector on the printer.

2. Connect the interface cable into the USB or Serial port of the device

(PDA, PC, etc.)

NOTE

Use only the cables oered by the printer manufacturer.

Serial

USB

16 17

5-1. PrintHead Cleaning

5. Printer cleaning

If the interior of the printer is dusty, printing quality can be lowered.

In this case, follow the instructions below to clean the printer.

NOTE

1. Make sure to turn the printer power o prior to cleaning

2. The printhead can become very hot during printing; allow the printer

approximately 10 minutes to cool before cleaning.

3. Do not touch the printhead, it can be damaged by static electricity.

4. Take care not to allow the print head to become scratched and /or

damaged in any way.

1. Use an applicator swab moistened with an isopropyl alcohol to clean

the print head and remove any dust.

2. Once cleaning is complete, allow the printer to dry then install the

stock and close the cover.

PrintHead

5-2. Platen Roller Cleaning

1.Clean the platen roller with a clean soft cloth moistened with isopropyl

alcohol or a cleaning pen.

2. Turn the platen roller with your nger to clean the entire surface.

Platen Roller

Altri manuali per Monarch 9485

Indice

Altri manuali Avery Dennison Stampante

Avery Dennison

Avery Dennison MONARCH 9416 XL Istruzioni per l'installazione e il funzionamento

Avery Dennison

Avery Dennison Monarch 9485 Guida utente

Avery Dennison

Avery Dennison M09416 XLI Manuale utente

Avery Dennison

Avery Dennison 9444 Manuale utente

Avery Dennison

Avery Dennison TrafficJet Manuale utente

Avery Dennison

Avery Dennison Monarch Sierra Sport2 Manuale di servizio

Avery Dennison

Avery Dennison Monarch 9419 Manuale di servizio

Avery Dennison

Avery Dennison TTX 207 Manuale utente

Avery Dennison

Avery Dennison Monarch 9419 Manuale utente

Avery Dennison

Avery Dennison FreshMarx 9417 Manuale utente

Avery Dennison

Avery Dennison MONARCH 9416 XL Documento tecnico

Avery Dennison

Avery Dennison ALS 104 Manuale utente

Avery Dennison

Avery Dennison Pathfinder6057 Manuale operativo e di manutenzione

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Silver 6032 Manuale di servizio

Avery Dennison

Avery Dennison Monarch 9419 Manuale di servizio

Avery Dennison

Avery Dennison Monarch ADTP1 Manuale utente

Avery Dennison

Avery Dennison APP 31x Manuale utente

Avery Dennison

Avery Dennison Monarch Tabletop Printer 1 Manuale di servizio

Avery Dennison

Avery Dennison MONARCH 9416 XL Manuale utente

Avery Dennison

Avery Dennison Monarch 9460 SNP Manuale di servizio

Avery Dennison

Avery Dennison Wireless Ethernet Print Server Monarch 7411 Manuale utente

Avery Dennison

Avery Dennison Monarch SIERRA SPORT4 9493 Manuale di servizio

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Platinum 9462 Manuale utente

Avery Dennison

Avery Dennison Platinum 6039 Manuale del proprietario

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente