To Contact AvocentTechnical Support:Visit www.avocent.com 590-973-501A
Avocent, the Avocentlogo, and Emerge are registered trademarks of AvocentCorporation orits affiliates in the U.S. and other countries. All othermarks are the property of theirrespective owners. ©2009 Avocent Corporation.
QUICK INSTALLATION GUIDE Emerge®MPX HD Extender
5Receiver Configuration
In the Active Receivers list (lower left of the
transmitter/access point’s web page), click on
the MAC address of the first active receiverto
access its web interface.
• Select the Display Device Settings page
to configure the output video mode of the
receiver.
- Plug-and-Play (default) - allows the receiver
to auto-detect DVI-D, HDMI and RGB
display devices if valid EDID information
can be read from the display via the DDC
channel; and component video displays
using Avocent component adapter cables.
- Manual (Component) - third-party
component video cables
- Manual (RGB) - non Plug-and-Play RGB
displays.
• Select the System Settings page and enter a
name for the receiver.
To configure the receiver to ignore all but the
currently detected transmitter/access point,
select the detected transmitter/access point in
the Bindings page to move it into the Configured
Transmitter table.The connection will reset.
Repeat for each receiver.
6Media LAN Settings- Optional
• For applications requiring only one receiver,
optimal performance can be achieved by
selecting 1-to-1inTopology Configuration
on the Media LAN Settings page of the
transmitter/access point.
•
If all receivers have been explicitly configured
(as described above) with the MAC address
of the transmitter/access point
, you may
disable ESSID broadcasting from the Media
LAN Settings page to hide them from other
wireless clients.
7Sending Video
Connect a source device to the transmitter
and a display device to each receiver. Activate
all devices and verify output on each display.
Helpful status information is available in the
Connection Status and Media LAN Performance
web pages on the transmitter/access point.
8Extender Placement and Mounting
Without firmly mounting the units, place the
transmitter and receivers in their desired
locations and re-attach the source and display
devices.Turn the units on and allow them to
bind.You may need to reposition the units
and antennas to obtain optimal performance.
Tuning suggestions are provided in the Emerge
MPXExtender Installer User Guide. Best
performance is obtained when all antennas
are similarly oriented and aligned on the same
horizontal plane.When the extension network
is performing properly, secure the units in place
without altering their orientation.
USA Notification
Warning: Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user’s authority to
operate the equipment.
Note:This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement:This
equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.This equipment should be installed
to provide a 20 cm separation from all persons.
This transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter. Operations in the 5.15-5.25GHz
band are restricted to indoor usage only.
Canadian Notification
This digital apparatus does not exceed the Class
B limits for radio noise emissions from digital
apparatus set out in the Radio Interference
Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de
bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la
classe B prescrites dans le Règlement sur le
brouillage radioélectrique édicté parle Ministère
des Communications du Canada.
Safety and EMC Approvals and
Markings
IEC 60950-1:2000, IEC 60065 :2001+ Amd
1:2005 EN 60950-1:2001, EN 60065 :2002 UL
60950 3rd Ed. / CSA 22.2No. 60950:2000,
UL60065 :2002, EN 55103-1:1997, EN
55022:1998+A1:2000+A2:2003,EN 61000-3-2
:1995 EN 61000-3-3:1995+A1:2001, EN 55103-
2:1997, EN 55024:1998+A1:2001+A2:2003,
FCC Part 15 Subpart B Class B, FCC Part 15
Subpart C, FCC Part 15 Subpart E, EN 50392
:2004, EN 301893 v. 1.4.1 (2003-08), EN 489-1
v. 1.4.1(2002-08), EN 489-17V. 1.2.1(2002-08)
EN 300 328 1.7.1 (2006-10)
Compliance Note
Only Avocent-supplied antennas used in a
configuration that is recommended by Avocent
are supported by this product.
