Avocent Cybex SwitchView SC8 DVI Manuale utente

Switching your servers

Press the appropriate front panel button labeled A-H to

access servers in your SwitchView switching system.

Environmental

Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)

Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)

Input Power: 60 W; Operating Voltage 100-240 VAC

Power Frequency: 50-60 Hz

The Power of Being There®

Quick Installation Guide

Cybex®SwitchView®

SC8 DVI Switch

The following instructions will help you

install your SwitchView SC8 DVI switch.

Should you require further assistance, please

contact Avocent Technical Support.

To install the Cybex SwitchView SC8 DVI switch

To Contact Avocent Technical Support CALL (888) 793-8763 VISIT www.avocent.com/support DOWNLOAD www.avocent.com

Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its afﬁliates. ©2006 Avocent Corporation. All rights reserved. 590-502-501C

Connecting local peripherals

Power down all servers that will be part of your

SwitchView SC8 DVI switching system. Locate

your PS/2 keyboard, DVI monitors and PS/2

mouse.

Plug your DVI monitor cables into the

CONSOLE ports on the left side of the back

of your switch

. Plug your PS/2 keyboard cable

and your PS/2 mouse cable into the keyboard

and mouse ports respectively.

Connecting your servers

Locate your ﬁrst cable set consisting of two

PS/2 cables and one or two DVI cables. The

SwitchView SC8 DVI switching system has

eight port sets labeled A-H on the rear of the

unit. Plug the two PS/2 cables (keyboard

and mouse) and the DVI cable (monitors)

into the corresponding ports on your server.

Plug the other ends into any available server port

setonyourSwitchViewSC8DVIswitchingsystem.

Repeat this process until all servers are properly

attached to the SwitchView SC8 DVI switch.

Powering your system

Locatethe powercordthatcamewithyour switch.

Plug one end into the IEC power connector on

the SwitchView switch. Ensure the power switch

is off, then plug the other end of the power cord

into an AC wall outlet. Power up your switch ﬁrst,

then power up all attached servers.

Power down all

connected servers.

Connect your

peripherals to the

CONSOLE ports

on the switch.

Connect the eight

servers to the

switch with the

provided cables.

Press the

appropriate front

panel button

labeled A-H to

access servers in

your system.

Supported Hardware

Server: IBM, PC/AT, PS/2 and 100% compatibles

Video Modes: VGA, SVGA, XGA, SXGA, UXGA,

HDTV and QXGA

Maximum Resolution: 2048 x 1536 @ 75Hz

Peripherals: PS/2 keyboard, PS/2 mouse and

IntelliMouse (PS/2 only)

Mechanical

H x W x D = 3.6” x 17.2” x 10.8” (9.1 x 43.7 x 27.4 cm)

Weight = 9.5 lbs (4.3 kg)

Power up

your system.

Optional

RF ground

(not required

for safety)

USA Notiﬁcation

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Canadian Notiﬁcation

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Japanese Approval

Safety and EMC

Approvals and Markings

UL, FCC, cUL, ICES-003, CE, VCCI, C-Tick

Safety certiﬁcations and EMC certiﬁcations for this product are obtained under one or more of the following

designations: CMN (Certiﬁcation Model Number), MPN (Manufacturer’s Part Number) or Sales Level Model

designation. The designation that is referenced in the EMC and/or safety reports and certiﬁcates are printed on the

label applied to this product.

Safety Precautions

DANGEROUS VOLTAGE

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

NOTE: The AC inlet is the main disconnect.

INSTRUCTIONS

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions.

RACK MOUNT SAFETY CONSIDERATIONS

• Elevated Ambient Temperature: If installed in a closed rack assembly, the operation temperature of the rack

environment may be greater than room ambient. Use care not to exceed the rated maximum operating temperature of

40° C for this product.

• Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of airﬂow required for safe

operation of the equipment is not compromised.

• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not

achieved due to uneven mechanical loading.

• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and

the effect that overloading of circuits might have on overcurrent protection and supply wiring. Consider equipment

nameplate ratings for maximum current.

• Reliable Earthing: Reliable earthing of rack mounted equipment should be maintained. Pay particular attention to

supply connections other than direct connections to the branch circuit (for example, use of power strips).

WARNING: To reduce the risk of electric shock or damage to your equipment:

- Do not disable the power grounding plug. The grounding plug is an important safety feature.

- Plug the power cord into a grounded (earthed) outlet that is easily accessible at all times.

- Disconnect the power from the switch by unplugging the power cord from either the electrical outlet or the appliance.

Altri manuali Avocent Interruttore

Avocent

Avocent AutoView 1415 Istruzioni di installazione e manutenzione

Avocent

Avocent AutoView AutoView 3200 Istruzioni di installazione e manutenzione

Avocent

Avocent DSR Series DSR1021 Istruzioni di installazione e manutenzione

Avocent

Avocent DSR Series DSR2035 Manuale di istruzioni

Avocent

Avocent DSR 1024 Istruzioni di installazione e manutenzione

Avocent

Avocent AMX Switch Series Istruzioni di installazione e manutenzione

Avocent

Avocent AutoView 1000R Manuale utente

Avocent

Avocent AutoView 1400 Manuale utente

Avocent

Avocent SwitchView 1000 Istruzioni di installazione e manutenzione

Avocent

Avocent KVM over IP switch Manuale utente

Avocent

Avocent AutoView 1000R Istruzioni di installazione e manutenzione

Avocent

Avocent AutoView 2020 Istruzioni di installazione e manutenzione

Avocent

Avocent Outlook 180DX Istruzioni di installazione e manutenzione

Avocent

Avocent AMX Switch Series Manuale utente

Avocent

Avocent ESP Serial Hub Istruzioni di installazione e manutenzione

Avocent

Avocent 120 Manuale utente

Avocent

Avocent SwitchView SC200 Series Manuale utente

Avocent

Avocent AutoView 416 Istruzioni di installazione e manutenzione

Avocent

Avocent AutoView 416 Istruzioni di installazione e manutenzione

Avocent

Avocent DSR Series DSR1020 Manuale di istruzioni

Avocent

Avocent DSR SWITCH - Istruzioni di installazione e manutenzione

Avocent

Avocent KVM Switching Manuale utente

Avocent

Avocent DSR SWITCH - Istruzioni di installazione e manutenzione

Avocent

Avocent SwitchView SC380 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente