AWS Blade-50 Manuale utente

American Weigh Scales, Inc.

BLADE-50

BLADE-100

BLADE-600

BLADE-1000

User Manual

BLADE Series

Digital Pocket Scale

Blade Manual

Thank you for purchasing the American Weigh Blade

Series digital pocket scale. Please read all operating

instructions carefully before use. Scales are precision

instruments and should always be handled with proper

care. To ensure years of reliable service, keep these

simple tips in mind:

• Do not exceed the scales maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, recalibration

may be necessary.

• Allow your scale to warm up for 30-60 seconds

before performing calibration (if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing sensors

and electronics causing innacuracy or malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Always weigh on a at and level surface, free from

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

I. OPERATION

Place Scale on a horizontal at surface.

1. Press [ON/OFF] key.

2. Wait until "0.0” is displayed.

3. Put the object(s) on the weighing platform.

4. Using the [MODE] key, you can switch between the

weighing units.

II. TARE WEIGHING

1. Turn on scale as described above.

2. Place the "tare item" on the platform.

3. Press [TARE] and wait until "0.0" is displayed.

4. Add the "net-weight-item".

III. CALIBRATION

Calibration is NOT required before rst use. Only

calibrate if scale is not weighing properly.

**Make sure you use the correct calibration weight for

your scale or the calibration will not be accurate**

BLADE-50: 50g calibration weight

BLADE-100: 100g calibration weight

BLADE-600: 500g calibration weight

BLADE-1000: 1000g calibration weight

1. Turn ON the scale.

2. Press and hold the [MODE] key until “CAL” is dis-

played. Release the [MODE] key.

3. Press [MODE] again. Now the display will read

“CAL” and the required calibration weight will ash 3

times.

4. Place the required calibration weight for your scale

on the center of platform. Wait 3-4 seconds. The LCD

will display “PASS”.

5. Remove the weight and press [ON/OFF] to turn off

the scale. Finished! Repeat if necessary.

IV. BLADE1000 Calibration Procedures

You will need a 1000g (1kg) calibration weight.

1. Turn on the scale by pressing [ON/OFF] key.

2. Wait until the LCD displays “0.0” then press and

HOLD the [MODE] key for 3 seconds. The LCD will

display “CAL”. You can now release the [MODE] key.

3. Press [MODE] key again, the LCD will display “CAL”

and “1000.0”.

4. Add 1000g calibration weight, the display will show

“PASS” and return to normal weighing mode.

5. Put away the calibration weight and press [ON/OFF]

to turn off the scale. Finished! Repeat if necessary.

V. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction

are low batteries, incorrect calibration, overload or

operating on an unstable surface. Please keep this in

mind and maintain and operate your scale properly.

This scale is a precise instrument and must be

handled with the utmost care and caution.

[Display] Elimination of errors

Nothing, Battery-Symbol, [lo] or [88888]

Change the batteries.

[OUE2] Recalibrate the scale as shown above.

[EEEEE] You are overloading the scale. Remove the

excessive load immediately!

[LLLLL] The delicate weighing load cells have

been damaged by misusing the scale

(i.e. it was shocked, dropped or

overloaded). You can try recalibrating the

scale. If the load cell has not been

damaged too much it will work

again after recalibration.

[UNST] Use the scale in a more stable position

Model Blade-600 Blade-1000 Blade-50 Blade-100

Capacity 600g

21.16oz

19.29ozt

385.8dwt

1000g

35.27oz

32.15ozt

643.0dwt

50g

1.764oz

250ct

771.5gn

100g

3.528oz

500ct

1543gn

Resolution 0.1g

0.01oz

0.01ozt

0.1dwt

0.01g

0.001oz

0.05ct

0.1gn (0.2gn minimum)

Weighing Units g, oz, ozt, dwt g, oz, ct, gn

Calibration Weight (not Included) 500g 1000g 50g 100g

Platform Dimensions (inches) 2.75 x 2.75 (Stainless Steel )

Scale Dimensions (inches) 3.75 x 3.75 x 0.75

Power 2 x AAA Batteries (included)

Specications

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Scala popolari di altre marche

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente

Fidelity Electronics

Fidelity Electronics G2e Manuale utente