AWS GeminiPRO Manuale utente

Indice

Manuali Scala popolari di altre marche

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente

Fidelity Electronics

Fidelity Electronics G2e Manuale utente

American Weigh

Scales, Inc.

Mini Jewelry

Scale

20g x 0.001g

100 x 0.01ct

GeminiPRO Manual

Thank you for purchasing the American Weigh

GeminiPRO Mini Jewelry Scale. Please read all

operating instructions carefully before use. Scales are

precision instruments and should always be handled

with proper care. To ensure years of reliable service,

keep these simple tips in mind:

• Do not exceed the scales maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature.

If temperatures have changed dramatically,

recalibration may be necessary.

• Allow your scale to warm up for 30-60 seconds

before performing calibration (if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing innacuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Always weigh on a at and level surface, free from

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

I. SCALE OPERATION

Place the scale on a horizontal at surface and set the scale

platform on the weighing surface.

1. Press [ ON/OFF ] key.

2. Wait until “0.000g” is displayed.

3. Place the object(s) on the weighing tray.

4. By pressing the [ MODE ] key, you can switch between

weighing units.

5. The weighing pan can be used by following the TARE

WEIGHING instructions below.

II. TARE WEIGHING

1. Turn on the scale as described above.

2. Place the included weighing pan on the scale platform.

3. Press the [ TARE ] button. “0.000g” will be displayed.

4. You can now add items to the pan to obtain just the weight

of the contents.

5. When all items are removed, a negative number will be

displayed. Press [ TARE ] again to zero the scale.

III. CALIBRATION

1. Press the [ ON/OFF ] key to turn the scale on.

2. Wait for the display to show “0.000g” then press and hold

the [ CAL ] key for 3 seconds until the display shows “CAL”

then release.

3. When the LCD ashes “10.000g”, place a 10g weight on the

middle of the platform.

4. The LCD will ash then ash “20.000g”. Place another 10g on

the center of the platform to make a total of 20g.

5. The LCD will display “PASS” and return to normal weighing

mode. Calibration is complete. You may now remove the

weights and turn o the scale.

IV. TROUBLESHOOTING

The primary reasons for inaccuracy or malfunction are low

batteries, incorrect calibration, overload or operating on an

unstable surface. Please keep this in mind and maintain and

operate your scale properly. This scale is a precise instrument

and must be handled with the utmost care and caution.

[Display] Elimination of errors

[Lo] Change the batteries.

[OUT2] Recalibrate the scale as shown above.

[O_Ld] You are overloading the scale. Remove the excessive

load immediately!

[UnSE] Use the scale in a more stable position

Model GeminiPRO

Capacity 20.000g / 12.860dwt / 100.00ct / 308.64gn

Resolution 0.001g /0.001dwt / 0.005ct / 0.02gn

Tolerance ±0.003g / 0.003dwt / 0.015ct / 0.06gn

Weighing Units g, dwt,ct, gn

Calibration Weight (not

Included) 10g and 20g

(calibrates linearly at 10g and 20g)

Platform Dimensions

(inches) 1.75” Ø

Scale Dimensions

(inches) 2.75 x 5.9 x 1.6”

Power 4 x AAA Batteries (included)

Warranty 10 Year Warranty

Specications

American Weigh Scales, Inc.

3285 Saturn Court

Norcross, GA 30092

www.awscales.com