AXIOMTEK CEM841 Manuale utente

4 9418D841000E

Version A1 March 2015

Printed in Taiwan

Quick Start

The basic procedures required to power on CEM841:

(1). Require +12V DC power at minimum 2.5A. Make sure the power is

OFF before connecting the CEM841.

(2). Check to ensure the onboard switch SW1-1 is set to default (OFF

position).

(3). Firmly install DDR3L SO-DIMM into DIMM2 (for single memory

channel configuration) or both DIMM2 and DIMM1 (for dual memory

channel configuration, make sure both memory modules are of the

same size, chip width, density and rank) until fully seated.

Note: It must be DDR3L memory module.

(4). Attach heatsink to the CEM841, refer to section Installing Heatsink.

(5). Install the CEM841 onto COM ExpressTM baseboard, for example,

CEB94000 baseboard.

(6). Properly install all necessary peripheral devices such as hard disk,

display, keyboard and etc. to the baseboard.

(7). Firmly attach power supply to baseboard’s power connector.

(8). Turn on the system power.

(9). Press power button on the baseboard to start CEM841.

CEM841 Quick Installation Guide

9418D841000E 1

Version A1 March 2015

Printed in Taiwan

Checklist

CEM841 Board x1 Product Information CD x1

Quick Installation Guide x1

Note: Please contact your local vendors if any damaged or missing items. DO

NOT apply power to the board if there is any damaged component.

Please refer to the product information CD for the complete user’s

manual, drivers and utilities. User’s manual and related documents are

in Acrobat PDF format.

Board Layout

Top View

CEM841 COM ExpressTM Type 2 Basic Module

2 9418D841000E

Version A1 March 2015

Printed in Taiwan

Bottom View

Switch Settings

Before applying power to the CEM841, please make sure all of the switches

are in factory default positions.

Switch Description Setting

Auto Power On

Default: Disable SW1-1 OFF

SW1 Restore BIOS Optimal Defaults

Default: Normal Operation SW1-2 OFF

SW2 PATA Device Setting

Default: Disable SW2-2 OFF

Connectors

Connector Description

DIMM1 Channel 1 DDR3L SO-DIMM Socket

DIMM2 Channel 0 DDR3L SO-DIMM Socket

SS1 COM ExpressTM Connector

SS2 COM ExpressTM Connector

9418D841000E 3

Version A1 March 2015

Printed in Taiwan

Installing Heatsink

For thermal dissipation, a thermal solution enables the CEM841’s

components to dissipate heat efficiently. All heat generating components

are thermally conducted to the heatsink in order to avoid hot spots. Figure

below illustrates how to install the thermal solution on CEM841.

1. There is a protective plastic covering on the thermal pads. This must be

removed before the heatspreader can be mounted.

2. Each thermal solution is designed for a specific CEM module. The

thermal pads on the heatspreader are designed to make contact with

the necessary components on the CEM module. When mounting the

heatspreader you must make sure that the thermal pads on the

heatspreader make complete contact (no space between thermal pad

and component) with the corresponding components on the CEM

module. This is especially critical for CEM modules that have higher

CPU speeds (for example 1.46GHz or more) to ensure that the

heatspreader acts as a proper thermal interface for cooling solutions.

3. Before installing the heatspreader to the CPU module, please apply

thermal grease on the CPU die. This CPU module has four assembly

holes for installing heatspreader plate. Use the four screws to secure

the heatspreader plate to the CEM841. Be careful not to over-tighten

the screws. Then, apply thermal grease at the bottom of heatsink and

secure the heatsink on the heatspreader by another four screws.

Altri manuali AXIOMTEK Hardware per computer

AXIOMTEK

AXIOMTEK CAPA880 Series Manuale utente

AXIOMTEK

AXIOMTEK CEM881 Manuale utente

AXIOMTEK

AXIOMTEK eBOX630A Series Manuale utente

AXIOMTEK

AXIOMTEK AIE100-ONA Series Manuale utente

AXIOMTEK

AXIOMTEK SHB250R Manuale utente

AXIOMTEK

AXIOMTEK rBOX204-FL Manuale utente

AXIOMTEK

AXIOMTEK SBC86808 Series Manuale utente

AXIOMTEK

AXIOMTEK eBOX625-853-FL Manuale utente

AXIOMTEK

AXIOMTEK CEM860 Manuale utente

AXIOMTEK

AXIOMTEK KIWI310 Manuale utente

AXIOMTEK

AXIOMTEK CEM881 Manuale utente

AXIOMTEK

AXIOMTEK Agent336-FL Series Manuale utente

AXIOMTEK

AXIOMTEK NANO830 Manuale utente

AXIOMTEK

AXIOMTEK AX10445 Series Manuale utente

AXIOMTEK

AXIOMTEK FAB113-13A7P4 Manuale utente

AXIOMTEK

AXIOMTEK rBOX310-FL Manuale utente

AXIOMTEK

AXIOMTEK UST510-52B-FL Series Manuale utente

AXIOMTEK

AXIOMTEK KIWI310 Manuale utente

AXIOMTEK

AXIOMTEK SBC8243 Manuale utente

AXIOMTEK

AXIOMTEK ETM831 Series Manuale utente

AXIOMTEK

AXIOMTEK eBOX560-300-FL Manuale utente

AXIOMTEK

AXIOMTEK CAPA13S Series Manuale utente

AXIOMTEK

AXIOMTEK CEM842 Manuale utente

AXIOMTEK

AXIOMTEK tBOX312-870-FL Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente