BARRON TRACE-LITE AXL2 Manuale utente
AXL2 (80-280W)
INSTALLATION INSTRUCTIONS
800.533.3948 • www.barronltg.com
Mounting Preparation
Slip Fitter (fits up to 2 3/8” OD)
1. Separate the slip-fitter from the knuckle by removing the adjustment bolt with a hex wrench (provided by
others) (Fig. 1).
2. Feed wire leads from the AXL2 through the knuckle and attached the knuckle to the head (Fig. 2).
3. Feed wire leads through the slip-fitter and then attach the slip-fitter to the knuckle (Fig. 3).
4. Electrical connections should be made at this time (see Wiring section).
5. Install the slip-fitter on the pole and secure with screws.
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
When using electrical equipment, basic safety precautions should always be followed including the following:
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations if applicable.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by
unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Any modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS!
Fig. 1 Fig. 2 Fig. 3
20070138 REV 1 P-5 - 2/19 1
Trunnion
1. Feed wire leads through slot in trunnion (Fig. 4).
2. Attach trunnion to the head (Fig. 5).
Yoke
1. Attach yoke to the head using a hex wrench (provided by others) (Fig 6).
INSTALLATION INSTRUCTIONS
800.533.3948 • www.barronltg.com
Fig. 4 Fig. 5
Fig. 6
20070138 REV 1 - 2/19
AXL2 (80-280W)
2
Surface/Pole Mounting
Slip-Fitter
1. Connect wires from AXL2 to supply (see Wiring section) and
position wires inside pole (Fig. 7)
2. Secure slip-fitter over pole and tighten.
3. To position, loosen the adjustment bolt using a hex wrench
(provided by others), position head as desired, then retighten
the bolt.
Notice: Adjustable angle is 0-90° (Fig. 7).
Arm
1. Disassemble the pole bracket from the arm.
2. If assembling to a round pole, remove and discard the adapter
gasket.
3. Using the pole bracket as a guide, drill holes in pole at desired
location.
4. Attach arm to pole with pole bracket inside pole.
5. Feed wire leads from the ALX2 through slot in arm.
6. Attach the AXL2 head to arm using adjustment bolt.
7. Adjust head to desired position and tighten adjustment bolt.
8. Wiring can be made inside the arm wiring compartment or inside
pole (see Wiring section).
9. Secure wiring cover to arm with gasket in between (Fig. 8)
Trunnion
1. Drill hole in mounting surface or rectangular pole.
2. Attach luminaire to mounting surface or retangular pole (Fig. 9).
3. Make supply connection in waterproof J-box or inside pole
(see Wiring section).
INSTALLATION INSTRUCTIONS
800.533.3948 • www.barronltg.com
Adjustment Bolt
Pole, round or rectangular
Slip Fitter
Pole
Bracket
Adapter
Gasket
Adjustment Bolt
Wiring Cover
Arm
Mounting surface
or rectangular pole
Fig. 7
Fig. 8
Fig. 9
20070138 REV 1 - 2/19
AXL2 (80-280W)
3
INSTALLATION INSTRUCTIONS
800.533.3948 • www.barronltg.com
Yoke
1. Drill hole in mounting surface or rectangular pole.
2. Attach AXL2 to mounting surface or rectangular pole
(Fig 12).
3. Make supply connection in waterproof J-box or inside pole
(see Wiring section).
Yoke Templates
Wiring
Make electrical connections as follows:
Black - Line
White - Neutral
Green/Yellow Green - Ground
If dimming is used:
Purple - Dim+
Gray - Dim-
Note: This fixture auto adjusts for voltages from 120-277V. Cap all
unused leads to prevent shorting.
IMPORTANT: Weatherproof your outdoor installation, be sure to seal
all holes in fixture housing. (Mounting, conduit, plugs, sensors and
photo-controls, etc.) with silicone sealant.
20070138 REV 1 - 2/19
Mounting surface
or rectangular pole
3"
2.3"
1.2"
3.3" 0.5"
6-Φ0.5"
80-140W
3"
2.3"
1.2"
3.3" 0.5"
6-Φ0.5"
240-280W
Φ0.8"
Φ0.79"
NEUTRAL
Fig. 12
LINE
NEUTRAL
AXL2 (80-280W)
4
Indice
Altri manuali BARRON Attrezzatura di illuminazione
BARRON
BARRON Exitronix S900C Series Manuale utente
BARRON
BARRON EXITRONIX LL30 Series Manuale utente
BARRON
BARRON Growlite GLE-GL Manuale utente
BARRON
BARRON Exitronix NFT Series Manuale utente
BARRON
BARRON GROWLITE GRM Manuale utente
BARRON
BARRON Exitronix TPXC Series Manuale utente
BARRON
BARRON Exitronix LED-90 Series Manuale utente
BARRON
BARRON EXITRONIX EQUITY QMR Series Manuale utente
BARRON
BARRON TRACE-LITE WTA Series Manuale utente
BARRON
BARRON EXITRONIX CRL Series Manuale utente
BARRON
BARRON Growlite GRM Manuale utente
BARRON
BARRON EXITRONIX VLED-90L Series Manuale utente
BARRON
BARRON Trace-Lite AXL2 Manuale utente
BARRON
BARRON EXITRONIX 400WX Series Manuale utente
BARRON
BARRON TRACE-LITE TL101 Manuale utente
BARRON
BARRON Exitronix 400U Series Manuale utente
BARRON
BARRON TRACE-LITE RHL-ACR Manuale utente
BARRON
BARRON Exitronix SCL Series Manuale utente
BARRON
BARRON EXITRONIX LED-51 Series Manuale utente
BARRON
BARRON specialityLED RFX Manuale utente
