BEA PANTHER Series Manuale utente

75.5172.08 PANTHER SERIES 20230420 Page 1 of 4

PANTHER SERIES

75.5172.08 PANTHER SERIES 20230420 Page 1 of 4

Push plate with integrated

900 MHz or 433 MHz wireless

transmitter

(US version)

ENGLISH

DESCRIPTION

1. Hex Key

2. Housing Assembly

3. Faceplate

4. Locking Tab

5. Mounting Bracket

6. Battery Enclosure

7. Mounting Keys

8. Mounting Holes

6 INCH ROUND, 433 MHz:

10EMR61 - logo & text

10EMR6 - text only

10EMR6L - logo only

4.75 INCH ROUND, 433 MHz:

10EMR4751 - logo & text

10EMR475 - text only

10EMR475L - logo only

4.75 INCH SQUARE, 433 MHz:

10EMS4751 - logo & text

10EMS475 - text only

10EMS475L - logo only

6 INCH ROUND, 900 MHz:

10EMR61-900 - logo & text

10EMR6-900 - text only

10EMR6L-900 - logo only

4.75 INCH ROUND, 900 MHz:

10EMR4751-900 - logo & text

10EMR475-900 - text only

10EMR475L-900 - logo only

4.75 INCH SQUARE, 900 MHz:

10EMS4751-900 - logo & text

10EMS475-900 - text only

10EMS475L-900 - logo only

Page 2 of 4 75.5172.08 PANTHER SERIES 20230420

Remove Housing Assembly from

Mounting Bracket by pressing in on

locking tab and sliding up.

Page 2 of 4 75.5172.08 PANTHER SERIES 20230420

• The device should not be used for purposes other than its intended use. All other uses cannot be

guaranteed by the manufacturer of the sensor.

• The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and

the door system in compliance with applicable national and international regulations and standards on door

safety.

• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate

adjustments of the sensor.

INSTALLATION

Install Mounting Bracket using at least

two (2) #8 countersunk head screws.

Any mounting holes may be used.

Observe “THIS END UP”.

Align Housing Assembly onto Mounting

Keys and slide down until Locking Tab

engages. To remove, press Locking Tab

and slide up.

Insert Faceplate into Housing Assembly

and use Hex Key to engage spring clips

on the top and bottom of Housing

Assembly. To remove, use Hex Key to

disengage spring clips.

NOTES:

1. For added security, additional screws may be installed through Housing Assembly and

Mounting Bracket during Step 2.

2. Ensure spring clips “click” during Faceplate installation. It may be necessary to rotate

Faceplate for proper alignment.

75.5172.08 PANTHER SERIES 20230420 Page 3 of 4

TROUBLESHOOTING

No activation Receiver not programmed Setup transmitter

Receiver improperly wired Verify power and activation

connection

Dead battery Replace battery

Constant activation Battery Housing screws

too tight

Loosen Battery Housing screws

Connected to door control

with NC (yellow) wire

Use NO (green) wire instead

Receiver set to Toggle

Mode

Set receiver to Pulse Mode

SETUP

To program the wireless receiver

(sold separately), please refer to the

appropriate User’s Guide:

• 900 MHz - 75.5786

• 433 MHz - 75.5092

• 433 MHz EH - 75.5659

900 MHz Panther series must use

a 900 MHz receiver and 433 MHz

Panther series must use a 433 MHz

receiver.

Remove four (4) screws on Battery

Enclosure.

• 900 MHz versions - two (2) CR2032

• 433 MHz versions - one (1) 12V

Type A23

DO NOT OVER TIGHTEN SCREWS

DURING REASSEMBLY. THIS MAY

CAUSE CONSTANT TRANSMITTER

ACTIVATION.

BATTERY REPLACEMENT

Page 4 of 4 75.5172.08 PANTHER SERIES 20230420

FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI

MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900

MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900

MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900

FCC ID: 2ABWS-10TD433PTRII IC: 4680-10TD433PTRII

MODEL: 10EMR61 MODEL: 10EMR4751 MODEL: 10EMS4751

MODEL: 10EMR6 MODEL: 10EMR475 MODEL: 10EMS475

MODEL: 10EMR6L MODEL: 10EMR475L MODEL: 10EMS475L

Page 4 of 4 75.5172.08 PANTHER SERIES 20230420

BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device;

therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.

BEA, Inc. strongly recommends that installation and service technicians be AAADM-certiﬁed for pedestrian doors, IDA-certiﬁed for doors/

gates, and factory-trained for the type of door/gate system.

Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring

that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.

Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s

recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must

be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.

ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).

Verify that all appropriate industry signage, warning labels, and placards are in place.

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

TECHNICAL SPECIFICATIONS

Dimensions 6” ROUND - 6.33” diameter, 1.45” depth

4.75” ROUND - 5.12” diameter, 1.42” depth

4.75” SQUARE - 5.12” height, 5.12” width, 1.42” depth

Weight 6” ROUND - 1.2 lbs

4.75” ROUND - 1.14 lbs

4.75” SQUARE - 1.04 lbs

Material FACEPLATE - stainless steel

HOUSING - ABS plastic

Transmitter Frequency 433 MHz or 900 MHz

Power 900 MHz versions - two (2) CR2032

433 MHz versions - one (1) 12V Type A23

Mounting Surface mount only

Certiﬁcation FCC, IC

Temperature 14 °F - 131 °F (-10 °C - 55 °C)

Enclosure Rating NEMA 4

Speciﬁcations are subject to change without prior notice.

All values measured in speciﬁc conditions.

PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING

©BEA|OriginalInstructions|75.5172.08PANTHERSERIES20230420

Tech Support & Customer Service: 1-800-523-2462

General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com

FCC / IC

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.”

Changes or modiﬁcations not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

Questo manuale è adatto per i seguenti modelli

Altri manuali BEA Unità di controllo