Beghelli LOGICA Manuale utente
LOGICA FM CONTROL UNIT BY BEGHELLI
code 21102
Co trol U it for the ce tralised co trol of ormal
a d emerge cy lighti g systems
NSTALLAT ON
AND OPERAT NG NSTRUCT ONS
2
ABLE OF CON EN S
•
•WHA IS HE LOGICA FM CON ROL UNI BY BEGHELLI p.3
•
•FUNC IONS p.3
System Monitoring p.3
System Control p.3
Keeping a Logbook p.3
•
•INS ALLA ION p.4
Use and termination of RS 485 lines p.4
Operations required to make the Logica FM Control Unit Operational p.5
Keyboard and Display Functions p.5
Date and Time Settings p.6
Searching for Logica FM Control Units (Node searching) p.7
Scheduling Functional and Autonomy Tests p.8
•
•GROUPS p.10
Assigning a Luminaire to a Group p.10
•
•MENU p.10
Luminaires Menu p.10
Maintenance Menu p.10
Manual Test p.10
Emergency p.11
Management Test p.12
Control Unit Management p.13
Date & Time Changes p.13
Printing p.13
Language p.14
Outputs OUT1 - OUT2 - OUT3 on/off p.14
Outputs OUT1 - OUT2 - OUT3 Active Open/Closed p.14
Configuration p.15
•
•ECHNICAL FEA URES p.16
•
•WARNINGS - WARRAN Y p.16
3
The Logica FM Control Unit by Beghelli (code 21102) is a device designed for the centralised con-
trol of normal and emergency lighting systems: it controls and supervises up to 992 Logica FM
series luminaires via radio. The Logica FM Control Unit by Beghelli consists of:
- Keyboard + display for user operations;
- Radio interface on the 2.4GHZ-2.4835GHz band, (code 12130) DSSS “Spread Spectrum” modu-
lation for connection to Logica FM series luminaires;
- RS485 interface for direct connection to a PC.
- RS232 interface for connection to the Logica D N RS232 serial printer by Beghelli (code
3284).
- USB interface for software updates, back-up and restoring configuration data.
- ntegrated 4G LTE modem for remote connections via nternet.
- Ethernet interface for LAN networks.
- Wi-Fi interface for PC connection.
To control the system from a remote PC, you need to get the Logica Visual software (code
12139) or the SD Manager software (code 20109).
The Logica FM Control Unit performs the following tasks:
SYS EM MONI ORING
The Logica FM Control Unit continuously monitors the luminaires connected to it and it detects
and signals any malfunctions.
SYS EM CON ROL
The Logica FM Control Unit allows you to adjust the brightness of luminaires, to perform
Functional and Autonomy Tests on emergency luminaires in the system, to schedule tests
(date, time and time intervals) etc.
KEEPING A LOGBOOK
The Logica FM Control Unit tracks test outcomes and, in general, any relevant operation in the
system. f a printer is available (code 3284), this information can be regularly printed on paper.
f a PC connection is available, this information can be sent and saved on a computer.
WHA IS HE LOGICA FM CON ROL UNI BY BEGHELLI
FUNC IONS
4
INS ALLA ION
Use the layout below for reference to connect the Logica FM Control Unit to the Logica FM radio
circuit and to the optional D N printer (RS232 bus).
The connection with the system, using the Logica Visual or the SD Manager software, can be
established through different channels:
- RS485-A;
- Ethernet;
- Modem 4G LTE integrato;
- Wifi
OkEsc
OUTPUT INPUT
Antenna
GSM
60425
LOGICA FM CONTROL UNIT
CODE 21102
RADIO CIRCUIT
LOGICA FM
CODE 1213 DIN PRINTER
CODE - 3284
DTR ( ELLOW)
TX (BLUE)
RX (GRE )
GND (BLACK)
USE AND ERMINA ION OF RS 485 LINES
The control unit is equipped with 2 independent RS 485 lines (RS485_A and RS485_B) both
with adaptation of the line impedance by inserting 2 riders at 2.54 pitch.
Line adaptation is necessary when the control unit is located as a "terminal" element of BUS
485 (start or end of the route).
To adapt the RS485_A line, insert the Jumper in connectors J22 and J23
To adapt the RS485_B line, insert the Jumper in connectors J20 and J21
CO
COM UX
-UX
+
RETE RADIO
PN
RS485_A
OUT3
R
+-
5V IN
Reset
BOOT
00 - SD
01 - eMMC
10 - NAND
Term. 485
J20
J21
J23
J22
5
OPERA IONS REQUIRED O MAKE HE LOGICA FM
CON ROL UNI OPERA IONAL
KEYBOARD AND DISPLAY FUNC IONS
Keys allow you to navigate through pages on screen to view information and select operating
modes.
The three main menus are LUM NA RES, MA NTENANCE AND STATUS;
- to move from one menu to another, use the "DOWN" Cand "UP" Dkeys
- to enter the menu and go deeper, use the "OK" Bkey
- to return to a higher menu level, use the "ESC” Akey
Other functions of the keys are listed below:
Use the “DOWN” Cand “UP” Dkeys to change a value (for example, in the Date and Time
Settings menu, with the hour indication “08” flashing, press Dto increase the value to “09”,
press Cto decrease the value to “07”) and press the “OK” Bkey to confirm the entered
value (by reference to the example given at the previous point: if, after changing the hours value
to “07”, you press the B key, the value will be stored on the Control Unit).
Note: f the panel is brand-new or if its memory has been reset (the Control Unit has no lumi-
naires stored), some menus will not be visible.
6
IME AND DA E SE INGS
At the first start up, the system displays the LUM NA -
RES menu: L MINAIRES
Press the keys shown on the right in sequence to go
to the menu for time setting:
CMAINTENANCE
BMaintenance CTRL
NIT MGT.
Dx2
B
Ctrl nit Mgt.
CHANGE DATE-TIME
Press Bto enter the menu that shows the date cur-
rently set on the Control Unit and the day indication
will be flashing. Press Duntil the day of interest is
displayed, then press Bto confirm. Now the month
indication will start flashing.
To change it, follow the same procedure as for setting
the day.
Change
date-time
01-01-2005 00:00
Apply the same method to set the year, hour and minu-
tes. Press Bto confirm the value set for minutes;
now the display will show "DONE".
15-06-2006 15:45
DONE
7
SEARCHING FOR FM LOGICA LUMINAIRES (NODE SEARCHING)
Note: nstall the Control Unit and activate the wizard for luminaire searching before starting to
install the luminaires. By doing so, whenever a luminaire is powered on, the Logica FM Control
Unit will detect it and will display a prompt. At the end of installation, the counter on the Control
Unit display should report the exact number of installed luminaires (if not, check for turned off
or faulty luminaires).
Press Bto run the search
Config. in pro-
gress CONTIN O S
SEARCH
As soon as the Control Unit acquires the first luminaire,
the display will show "NORMAL SEARCH", which will
then be replaced by the following indications:
- 008(008): number of luminaires found (total number
of luminaires stored on the Control Unit)
Config. in
progress 008
(008)
When the total number of luminaires stored on the
Control Unit reaches the number of luminaires installed
in the system, press Aand this screen will appear
showing how many luminaires have been found and, in
parentheses, the total number of luminaires stored on
the Control Unit.
SEARCH
COMPLETED
FO ND 098(098)
Assuming you start from the LUM NA RES menu: press
the keys shown on the right in sequence to go to the
luminaire searching menu (NODE SEARCH NG).
L MINAIRES
CMAINTENANCE
BMaintenance
CTRL NIT MGT
DMaintenance
CONFIG RATION
BConfiguration
FIND NODES CONT.
8
SCHEDULING FUNC IONAL AND
AU ONOMY ES S
Functional and Autonomy Tests check the emergency luminaires. A Functional Test consists in
turning on a luminaire for about 30 seconds during which time the luminaire light source and
battery efficiency is checked; an Autonomy Test consists in turning on a luminaire over a lon-
ger time at the end of which the battery efficiency is checked. f a test reveals a luminaire is faulty,
this information will be transferred from the luminaire to the Logica FM Control Unit: an error mes-
sage will be displayed on screen and the error will be recorded in the Logbook.
For a correct operation of the system, the following must be set:
- Date and time of the next Functional Test;
- Date and time of the next Autonomy Test;
- Time interval between repeated Functional Tests;
- Time interval between repeated Autonomy Tests.
Example of how to set the date and time for the next Functional Test:
Now press Bto show the date of the next Functional
Test currently stored on the Control Unit.
To set the time of the test, proceed as shown in section
"Date and Time Settings".
Next Func Test
31-12-2099 00:00
Assuming you start from the LUM NA RES menu: press
the keys shown on the right in sequence to go to the
date&time settings menu for the next Functional Test.
("x 2" means you have to press the key twice)
L MINAIRES
CMAINTENANCE
BMaintenance
MAN AL TEST
C x2 Maintenance
MANAGEMENT TEST
BAll
NEXT F NC TEST
9
Luminaires connected to each Logica Control Unit by Beghelli can be divided into groups to
perform separate operations on system sections. Each luminaire can belong to a group, multi-
ple groups or no group. The total number of groups available is 16.
ASSIGNING A LUMINAIRE O A GROUP
GROUPS
Press Band the following screen will appear on the
display. The line below the name of the luminaire indi-
cates whether it belongs to one of the sixteen groups or
not: the first digit on the left refers to group 1, the last
digit on the right refers to group 16:
- 0: the luminaire does not belong to the group
- 1: the luminaire belongs to the group
Before the first configuration, the row has sixteen '0',
i.e. the luminaire F12345 does not belong to any group;
the cursor will flash on the last zero to the left that cor-
responds to group 1.
Press:
-Bto move to the next group
-Ato move to the previous group
-Dto include the luminaire in the group
-Cto exclude the luminaire from the group
SA/PS F12345
0000000000000000
Assuming you start from the LUM NA RES menu: press
the keys shown on the right in sequence to go to the
menu to set the group of the first luminaire on the list
("x 4" means you have to press the key four times)
L MINAIRES
CMAINTENANCE
BMaintenance
MAN AL TEST
C x4 Maintenance GRO P
MANAGEMENT
BGroup Management
ALL
CGroup Management
SA/PS F12345
10
The system is organised in menus that allow you to access varied features of the system: turn
luminaires on and off, perform Functional and Autonomy Tests, review information on mal-
functions etc.
To understand how to navigate among screens using the keys, see section "Keyboard and
Display Functions".
Most operations available can be applied to the entire system or to parts of it, as shown in the
following table:
There are 3 menus: LUM NA RES, MA NTENANCE AND STATUS.
LUMINAIRES MENU
Use this menu to adjust the brightness of the luminaires:
MAIN ENANCE MENU
MANUAL ES
Functional and Autonomy Tests check the emergency luminaires. A Functional Test consists in
turning on a luminaire for about 30 seconds during which time the luminaire tube and battery
efficiency is checked; an Autonomy Test consists in turning on a luminaire over a longer time
at the end of which the battery efficiency is checked.
Normally, Functional and Autonomy Tests are run automatically at regular intervals according
to the schedule set by the user (see Scheduling Functional and Autonomy Tests"), but it is also
possible to perform a Functional Test or an Autonomy Test directly from the keyboard: Manual
Test. Manual Tests stop at the end of the set time or by sending a stop test command.
For: go to (menu):
all luminaires in the system ALL
a single luminaire (e.g. luminaire LOG CA SA
code F01234) SA/PS F01234
all luminaires in Group yy GROUP 03
go to (menu):
for a maximum brightness level ON (MAX)
to turn them off TO TURN THEM OFF
for an intermediate brightness level (e.g.
level 5) D MMER STEP 05
MENU
Altri manuali per LOGICA
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Beghelli Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
