Behringer PRO-1 Manuale utente

page 1 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings. If you do not feel comfortable

doing these calibrations, then we recommend they are done by an experienced audio service technician. This is especially true

for those units that need to be opened to gain access to voltage test points and calibration potentiometers.

CAUTION: Incorrect calibration or damage to the delicate adjustment potentiometers may lead to the unit

becoming inoperable.

Note: Although re-calibration will not invalidate the warranty, any damage caused during re-calibration may invalidate

the warranty.

Analog Synthesizer with Dual VCOs,

3 Simultaneous Waveforms, 4-Pole VCF,

Extensive Modulation Matrix, 16-Voice

Poly Chain and Eurorack Format

Synthesizers and Samplers

PRO -1

User Support Document

Equipment required

1. Small insulated trimmer screwdriver.

2. Small Phillips screwdriver.

3. A at sheet of cardboard or another insulator as wide as the PRO 1. (This will help prevent damage to the top panel when it is

inverted and resting on the bottom chassis).

4. Digital DC Voltmeter with a scale that can display accurately to 0.001 V.

5. Guitar tuner

6. An external MIDI keyboard of at least 6 octaves including A1 and A7.

7. MIDI cable.

8. Pair of headphones or a sound system to monitor the main output.

Important Note:

Leave the PRO 1 turned on for approximately 30 minutes. This will allow the circuits time to warm up and the components and

performance to stabilize with temperature. Without this warm-up time, the calibrations

will be inaccurate.

Introduction

page 2 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

page 2 of 6

Turn over the top panel to gain access to the bottom surface of the printed circuit board (pcb). Be careful not to strain

the ribbon cables. Use the cardboard to protect the top panel.

Caution:

Make sure that the circuit board is not touching any bare metal that may cause a short circuit and damage the unit.

Do not touch the circuit board while the unit is powered up.

Remove the 8 screws holding the top panel to the chassis.

Preparation

Remove all cables and connections to the unit.

Carefully connect the power and turn on the unit.

Leave the unit turned on for approximately 30 minutes.

Synthesizers and Samplers

PRO -1

Follow all steps in the order in which they are presented.

page 3 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

page 3 of 6

Synthesizers and Samplers

PRO -1

Oscillator Calibration using a guitar tuner:

Figure 1

Calibration Procedure

OSCA Calibration

Turn on the OSCA SAW switch.

The positions of knobs and switches are shown in red on Figure 1.

On your external keyboard, press the A1 key and adjust the OSCA FREQUENCY on the front panel to zero while

observing the tuner display. A1 should be 55 Hz.

Connect a guitar tuner to the rear panel main ¼" output.

Note that a pitch within 2 to 3 cents of the target frequency should be ne.

Please pay special attention to the FREQUENCY knobs of Oscillator A and B.

page 4 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

page 4 of 6

Synthesizers and Samplers

PRO -1

OSCB Calibration

Turn on the OSCB SAW switch and KYBD.

On your external keyboard, press the A1 key and adjust the OSCB FREQUENCY on the front panel while

observing the tuner display.

On your external keyboard, press the A4 key and adjust the OSCB SCALE trimmer while observing the tuner display.

Repeat steps 3 and 4 until both frequencies are correct A1 - 55 Hz and A4 - 440 Hz.

On your external keyboard, press the A7 key and adjust the OSCA TRIM trimmer while observing the tuner display.

Turn OFF the OSCA SAW switch.

Press A1 key again check how much the frequency has drifted and adjust this frequency with

OSCA OFFSET trimmer back to 55 Hz.

On your external keyboard, press the A4 key and adjust the OSCA SCALE trimmer while observing the tuner display.

This should be trimmed to 440 Hz.

page 5 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

page 5 of 6

Synthesizers and Samplers

PRO -1

Connect the positive probe of your Voltmeter to TP3.

OCTAVE Calibration (factory mode)

Set the Digital Voltmeter to measure a range below 10 VDC.

Locate the Test Points OCTAVE CV TP3 and ground (the red arrow in Figure 2) on the bottom surface of

the main PCB.

Figure 2

Repeat the same steps as oscillator A but using OSCB SCALE and OSCB OFFSET trimmers.

On your external keyboard, press the A7 key and adjust the OSCB TRIM trimmer while observing the tuner display.

page 6 of 6

985-40000-01090 Rev.A

2021-02-16

Condential, for internal use only. Not to be reproduced.

page 6 of 6

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

Synthesizers and Samplers

PRO -1

Connect the negative probe of your Voltmeter to ground.

Turn o the power and unplug the power connector.

Measure the output voltage. It should read +2.000 VDC.

Make sure the internal connections are still correctly inserted and secured.

If not, then adjust the OCT ADJ potentiometer until the measured output voltage is +2.000 VDC.

Ret the top panel back into the bottom chassis and secure with all the screws.

This calibration is done after the oscillator calibration. The positions of knobs and switches are shown in red on Figure 1.

Connect a guitar tuner to the rear panel main 1/4" output.

OCTAVE Calibration (user mode)

Turn on the OSCA SAW switch.

Set the position of the OCTAVE switch to 0. On your external keyboard, press the A1 key.

Set the position of the OCTAVE switch to 3. Adjust the OCT ADJ trimmer until there are zero beats.

End of Procedure

Altri manuali per PRO-1

Indice

Altri manuali Behringer Sintetizzatore

Behringer

Behringer 962 SEQUENTIAL SWITCH Manuale utente

Behringer

Behringer PRO-VS MINI Manuale utente

Behringer

Behringer POLY D Manuale utente

Behringer

Behringer CAT Guida di riferimento

Behringer

Behringer CRAVE Istruzioni per l'installazione

Behringer

Behringer EDGE Manuale utente

Behringer

Behringer DEEPMIND 12 Manuale utente

Behringer

Behringer PRO-1 Manuale dell'operatore

Behringer

Behringer NEUTRON Istruzioni operative e di manutenzione

Behringer

Behringer DeepMind 6 Manuale utente

Behringer

Behringer MonoPoly Manuale utente

Behringer

Behringer DEEPMIND 12 Manuale utente

Behringer

Behringer NEUTRON Manuale utente

Behringer

Behringer CRAVE Manuale utente

Behringer

Behringer 112 DUAL VCO Manuale utente

Behringer

Behringer 110 VCO/VCF/VCA Manuale utente

Behringer

Behringer DEEPMIND 12 Manuale utente

Behringer

Behringer Legendary 2500 Series Manuale utente

Behringer

Behringer Victor Manuale utente

Behringer

Behringer CRAVE Manuale utente

Behringer

Behringer DEEPMIND 12 Manuale utente

Behringer

Behringer PRO-VS MINI Manuale utente

Behringer

Behringer MS-1-BK Manuale

Behringer

Behringer K-2 Manuale utente

Manuali Sintetizzatore popolari di altre marche

Kawai

Kawai MP7 Manuale tecnico

Joranalogue

Joranalogue Contour 1 Manuale utente

Full Bucket Music

Full Bucket Music Mono/Fury Manuale utente

Kawai

Kawai PH50 Manuale utente

IK Multimedia

IK Multimedia UNO Synth PRO X Manuale utente

Roland

Roland Gaia SH-01 Manuale utente

Roland

Roland GR-30 Manuale utente

Gotharman

Gotharman Gotharman's anAmoNo-box Manuale utente

Yamaha

Yamaha DX21 Manuale utente

QuStream

QuStream HDFS-550 Manuale utente

Modal Electronics

Modal Electronics ARGON8 Manuale utente

Roland

Roland GS-500 Manuale utente

Octave

Octave Cat SRM Manuale utente

Dreadbox

Dreadbox Murmux Initiate Manuale utente

neutral labs

neutral labs ELMYRA 2 Manuale utente

Waldorf

Waldorf KYRA Manuale utente

Tubbutec

Tubbutec Juno-66 Manuale utente

EFM

EFM VCADSR - 3510 Manuale utente