BenQ TK860i Manuale utente
Digital Projector
User Manual
Home Entertainment Series l TK860i V1.00
2 Warranty and Copyright information
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal usage and
storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be
defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be
replacement of any defective parts (labor included). To obtain warranty service, immediately notify the
dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance
with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%,
temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the
projector in a dusty environment. This warranty gives you specific legal rights, and you may have other
rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright © 2022 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are
copyrights of their respective companies or organizations.
Patents
Please go to http://patmarking.benq.com/ for the details on BenQ projector patent coverage.
3 Table of Contents
Table of Contents
Warranty and Copyright information ................................................................................ 2
Important safety instructions .............................................................................................. 4
Introduction .......................................................................................................................... 7
Shipping contents ....................................................................................................................................... 7
Projector exterior view ............................................................................................................................ 8
Controls and functions.............................................................................................................................. 9
Positioning your projector ................................................................................................. 11
Choosing a location .................................................................................................................................11
Obtaining a preferred projected image size....................................................................................... 12
Shifting the projection lens ....................................................................................................................13
Mounting the projector ..........................................................................................................................13
Adjusting the projected image............................................................................................................... 15
Connection .......................................................................................................................... 16
Operation ............................................................................................................................ 17
Installing the QS02 Android TV dongle ..............................................................................................17
Starting up the projector ........................................................................................................................17
QS02 Android TV setup......................................................................................................................... 20
Using the menus ....................................................................................................................................... 22
Upgrading firmware .................................................................................................................................23
Switching input signal............................................................................................................................... 24
Presenting from a Media Reader........................................................................................................... 25
Shutting down the projector .................................................................................................................26
Direct power off ......................................................................................................................................26
Menu operation ................................................................................................................... 27
Basic menu ...............................................................................................................................................27
Advanced menu ..................................................................................................................................... 29
Maintenance ........................................................................................................................ 38
Care of the projector ..............................................................................................................................38
Lamp information .....................................................................................................................................38
Troubleshooting ................................................................................................................. 45
Specifications ...................................................................................................................... 46
Projector specifications ..........................................................................................................................46
Dimensions ................................................................................................................................................47
Timing chart............................................................................................................................................... 48
4 Important safety instructions
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in this manual and marked on the product.
1. Please read this manual before you
operate your projector. Save it for future
reference.
2. Do not look straight at the projector
lens during operation. The intense light
beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
4. Always open the lens shutter (if any) or
remove the lens cap (if any) when the
projector lamp is on.
5. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
6. In some countries, the line voltage is NOT
stable. This projector is designed to operate
safely within a mains voltage between 100 to
240 volts AC, but could fail if power cuts or
surges of ±10 volts occur. In areas where
the mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a power
stabilizer, surge protector or
uninterruptible power supply (UPS).
7. Do not block the projection lens with any
objects when the projector is under
operation as this could cause the objects to
become heated and deformed or even cause a
fire. To temporarily turn off the lamp, use the
blank function.
8. Do not operate lamps beyond the rated lamp
life. Excessive operation of lamps beyond the
rated life could cause them to break on rare
occasions.
5 Important safety instructions
9. Never replace the lamp assembly or any
electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart,
stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector.
There are dangerous high voltages inside
which may cause death if you should come
into contact with live parts. The only user
serviceable part is the lamp which has its own
removable cover.
Under no circumstances should you ever
undo or remove any other covers. Refer
servicing only to suitably qualified professional
service personnel.
12. Do not block the ventilation holes.
- Do not place this projector on a blanket, bedding or
any other soft surface.
- Do not cover this projector with a cloth or any other
item.
- Do not place inflammables near the projector.
If the ventilation holes are seriously
obstructed, overheating inside the projector
may result in a fire.
13. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more than 10
degrees left to right, nor at angle of more than 15
degrees front to back. Using the projector when it is
not fully horizontal may cause a malfunction of, or
damage to, the lamp.
14. Do not stand the projector on end vertically.
Doing so may cause the projector to fall over,
causing injury or resulting in damage to the
projector.
15. Do not step on the projector or place any
objects upon it. Besides probable physical
damage to the projector, doing so may result
in accidents and possible injury.
16. When the projector is under operation, you
may sense some heated air and odor from its
ventilation grill. It is a normal phenomenon
and not a product defect.
6 Important safety instructions
17. Do not place liquids near or on the projector.
Liquids spilled into the projector may cause it
to fail. If the projector does become wet,
disconnect it from the power supply's power
outlet and call BenQ to have the projector
serviced.
18. This product is capable of displaying inverted
images for ceiling/wall mount installation.
19. This apparatus must be earthed.
20. Do not place this projector in any of the
following environments.
- Space that is poorly ventilated or confined. Allow at
least 50 cm clearance from walls and free flow of air
around the projector.
- Locations where temperatures may become
excessively high, such as the inside of a car with all
windows rolled up.
- Locations where excessive humidity, dust, or cigarette
smoke may contaminate optical components, shorten
the projector's life span and darken the image.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C /
104°F
- Locations where the altitudes are higher than 3000 m
(10000 feet).
• Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
• To avoid damaging the DLP chips, never aim a high-power laser beam into the projection lens.
3000 m
(10000 feet)
0 m
(0 feet)
7 Introduction
Introduction
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items are missing,
please contact your place of purchase.
Standard accessories
Optional accessories
Replacing the remote control batteries
1. Press and open the battery cover, as illustrated.
2. Remove the old batteries (if applicable) and install two
AAA batteries. Make sure that the positive and negative
ends are positioned correctly, as illustrated.
3. Replace the battery cover until it clicks into place.
Projector Android TV remote control
with batteries Power cord
Quick start guide Warranty card* QS02 Android TV dongle kit
with batteries
• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
1. Spare lamp kit 2. 3D glasses
• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen,
bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for
your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the
batteries to avoid damage to the remote control from possible battery leakage.
8 Introduction
Projector exterior view
1. Lamp cover
2. Adjuster feet
3. Projection lens
4. IR remote sensor
5. External control panel
(See Controls and functions on page 9.)
6. Lens shift wheel
7. Zoom ring
8. Focus ring
9. Kensington anti-theft lock slot
10. Vent (air inlet)
11. 12V DC output terminal
Triggers external devices such as an electric
screen or light control, etc.
12. RS-232 control port
13. USB Mini-B port (for firmware upgrades)
14. USB Type-A port (1.5A media reader/drive,
firmware download)
15. Audio output jack
16. SPDIF output port
17. HDMI 1/ HDMI 2/ HDMI 3 input port (HDCP
2.2)
18. USB Type-A port (2.5A power supply)
19. AC power jack
20. Wall mount holes
21. Vent (air exhaust)
22. Security bar
M4 X8L
M4 X8L
12V
TRIGGER -
RS 232
AUDIO
OUT
MEDIA
READER
SERVICE 25A
SPDIF
5
19
22
20
20
20
2
412
13 15
14 17
16 18
2
2
2
2
2
20
20
20
22
2
1
11
21
4
3
6
7
8
10
9
2
9 Introduction
Controls and functions
Projector & Android TV remote control
1. OK
Confirms a selected item of ATV or projector
OSD menu.
When the input source is ATV, press OK to
play or pause a video or audio file during
media playback.
2. POWER
Toggles the projector between standby mode
and on.
ON/ Off
Toggles the projector between standby mode
and on.
3. / Back
When the input source is in ATV, press Back
to go back to previous ATV option, closes ATV
warming or reminder pop-up menu, and exits
current Android application package
application under ATV source.
When the projector OSD menu is on, press
Back to go back to previous projector OSD
menu, closes projector warming or reminder
pop-up menu, exits and saves projector menu
settings.
4. / Menu
Turns on the On-Screen Display (OSD) menu.
5. POWER indicator light/TEMPerature
warning light/LAMP indicator light
(See Indicators on page 44.)
6. Arrow keys ( , , , )
Navigates up/down/left/right to select a
desired ATV or projector OSD menu item.
7. / Source
Displays the source selection bar.
8. Mute
Toggles projector audio between on and off.
4
3
6
7
2
1
5
OK
POWER TEMP LAMP
All the key presses described in this document
are available on the remote control or projector.
2
21
15
16
19
11
6
7
14
13
17
8
10
18
20
1
3
4
9
12
10 Introduction
Remote control effective range
The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR
remote control sensor(s) to function correctly. The distance between the remote control and the
sensor(s) should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor(s) on the
projector that might obstruct the infra-red beam.
9. Rewind
Rewind video or audio playback.
10. Filmmaker
Switch Picture Mode to Filmmaker mode.
Available on compatible projectors only.
11. Microphone
Receives voice command.
12. Focus
Press to open Auto focus page. Available on
compatible projectors only.
13. 2D Keystone correction key
Displays the 2D Keystone correction menu.
14. Voice search / Voice assistant
Press and hold the Voice search / Voice
assistant button to activate voice assistant.
Hold this key and speak to the microphone at
the top of the remote control while using
voice assistant.
15. Android TV home screen
Displays Android TV home screen.
16. Android settings
Displays Android settings.
17. Volume keys
Decreases or increases the projector volume.
18. Fast forward
Fast forward current video or audio playback
19. Play / Pause
Play/Pause a video or audio playback
20. Sound mode
Displays sound mode menu.
21. Picture mode
Displays the Picture Mode menu.
Do not block the projection lens from
projecting as this could cause the blocking
object to become heated and deformed or
even cause a fire.
• Operating the projector from the front • Operating the projector from the top
Approx. +30º
Approx. +30º
Indice
Altri manuali BenQ Proiettore
BenQ
BenQ S11 Manuale utente
BenQ
BenQ PB8250 - XGA DLP Projector Manuale utente
BenQ
BenQ MX823ST Manuale utente
BenQ
BenQ MW621ST Manuale utente
BenQ
BenQ MX763 Manuale utente
BenQ
BenQ MX852UST Manuale utente
BenQ
BenQ MW855UST+ Manuale utente
BenQ
BenQ MX850UST Manuale utente
BenQ
BenQ LW61ST Manuale utente
BenQ
BenQ MX766 Manuale utente
BenQ
BenQ LX890UST Manuale utente
BenQ
BenQ W1060 Manuale utente
BenQ
BenQ PE8700 - DLP Projector - HD Manuale utente
BenQ
BenQ LU9915 Manuale utente
BenQ
BenQ MS500 Manuale utente
BenQ
BenQ W1200 Manuale utente
BenQ
BenQ Home Cinema PE8720 Manuale utente
BenQ
BenQ MX816ST Manuale utente
BenQ
BenQ Installation Series PB8250 Manuale utente
BenQ
BenQ MW814ST Manuale utente
