Binary B-520-MTRX-230-8x8 Manuale utente

Source | Mute | 2ch

(HDMI Out Audio)

INSTALLATION

MANUAL

HDMI MATRIX SWITCHER

B-520-MTRX-230-8x8

B-520-MTRX-230-6x4+2

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of re or electric shock, read and follow all instructions and warnings in this manual. Keep this

manual for future reference.

1. Do not expose this apparatus to rain or moisture. Do not expose this equipment to dripping or splashing, and

ensure that no objects lled with liquids, such as vases, are placed on the equipment. Do not use this apparatus

near water.

2. Do not remove cover. No user serviceable parts inside.

3. Clean only with a dry cloth.

4. Do not block any ventilation openings. Install according to manufacturer’s instructions.

5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including

ampliers) that produce heat.

6. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has two blades, one

of which is wider than the other. A grounding plug has two matching blades and a third grounding prong. The

wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet,

consult an electrician for replacement of the obsolete outlet.

7. Protect the power cord from being walked on or pinched, particularly at the plug end and where the power

cord is attached to the apparatus.

8. Only use attachments and accessories specied by the manufacturer.

9. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged

in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled on or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus does not operate

normally, or it has been dropped.

10. To completely disconnect this equipment from power, disconnect the power supply cord from the power

outlet.

LEGAL NOTICE

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK.

DO NOT REMOVE COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CONTENTS

1. Product Overview...................................................................................................................................................................................................................................................................4

2. Features.......................................................................................................................................................................................................................................................................................4

3. Package Contents....................................................................................................................................................................................................................................................................4

4. Recommended for Installation...........................................................................................................................................................................................................................................5

5. Device Layout............................................................................................................................................................................................................................................................................5

5.1. Front Panel of the B-520-MTRX-230-8x8 Switcher...................................................................................................................................................................................5

5.2. Rear Panel of the B-520-MTRX-230-8x8 Switcher ....................................................................................................................................................................................6

5.3. Front Panel of the B-520-MTRX-230-6x4+2 Switcher .............................................................................................................................................................................7

5.4. Rear Panel of the B-520-MTRX-230-6x4+2 Switcher...............................................................................................................................................................................8

6. Installation & Setup.................................................................................................................................................................................................................................................................9

6.1. B-520-MTRX-8x8 Basic Installation Diagram ..............................................................................................................................................................................................9

6.2. Basic Instructions......................................................................................................................................................................................................................................................10

6.3. Installation Tips..........................................................................................................................................................................................................................................................10

6.4. Switcher Location and Placement ...................................................................................................................................................................................................................... 11

6.4.1. Rack Installation.......................................................................................................................................................................................................................................... 11

6.5. HDMI Input Connections.......................................................................................................................................................................................................................................11

6.6. Output Connections ................................................................................................................................................................................................................................................12

6.6.1. Choosing the Correct Output Connection.......................................................................................................................................................................................12

6.6.2. HDMI Outputs .............................................................................................................................................................................................................................................12

6.6.3. HDBaseT Outputs ......................................................................................................................................................................................................................................12

6.6.3.1. HDBaseT Wiring Recommendations....................................................................................................................................................................................12

6.6.3.2. Installation Instructions.............................................................................................................................................................................................................13

6.7. Matrix Control Connections.................................................................................................................................................................................................................................13

6.7.1. Matrix Control Connections ..................................................................................................................................................................................................................13

6.7.2. RS-232 Control............................................................................................................................................................................................................................................ 14

6.7.3. Ethernet/IP Control...................................................................................................................................................................................................................................14

6.8. IR Passthrough Installation and Setup..............................................................................................................................................................................................................14

6.8.1. Matrix Switcher IR Connections........................................................................................................................................................................................................... 15

6.8.2. Matrix Switcher IR Port Conguration ..............................................................................................................................................................................................15

6.9. B-520-RX-230-IR IR Connections...................................................................................................................................................................................................................... 16

6.9.1. Point-to-Point IR Control - Stereo (3.5mm) IR Receiver.............................................................................................................................................................16

6.9.2. Control System - Mono (3.5mm) IR .....................................................................................................................................................................................................16

6.9.3. IR Flasher........................................................................................................................................................................................................................................................16

6.10. IR Application Diagrams......................................................................................................................................................................................................................................17

6.10.1. IR Passthrough from Control System............................................................................................................................................................................................... 17

6.10.2. IR Passthrough from Rooms to Sources..........................................................................................................................................................................................19

7. EDID Conguration................................................................................................................................................................................................................................................................20

7.1. Source Setup ...............................................................................................................................................................................................................................................................20

7.2. Display Setup ..............................................................................................................................................................................................................................................................21

7.3. Auto EDID Conguration.......................................................................................................................................................................................................................................21

7.3.1. How to Congure Auto EDID ................................................................................................................................................................................................................21

7.4. Embedded EDID Conguration...........................................................................................................................................................................................................................21

7.4.1. Embedded EDID Chart.............................................................................................................................................................................................................................21

7.4.2. How to Set Embedded EDID for a Single Input...............................................................................................................................................................................22

7.4.3. How to Set Embedded EDID for All Inputs....................................................................................................................................................................................... 22

7.5. EDID Learning ............................................................................................................................................................................................................................................................22

7.5.1. How to Learn EDID to a Single Input ..................................................................................................................................................................................................23

7.5.2. How to Learn EDID to All Input ............................................................................................................................................................................................................23

7.6. Viewing Input EDID Status.................................................................................................................................................................................................................................... 23

8. Advanced Setup Using the Conguration Utility........................................................................................................................................................................................................24

8.1. IR Source Routing...................................................................................................................................................................................................................................................... 24

8.2. IR Front Panel IR Enable.........................................................................................................................................................................................................................................24

8.3. Matrix Control from Room Enable.....................................................................................................................................................................................................................24

8.4. Front Panel Power Button Active.......................................................................................................................................................................................................................24

9. Firmware Update..................................................................................................................................................................................................................................................................... 25

10. Operation and Control .......................................................................................................................................................................................................................................................25

10.1. IR Remote .................................................................................................................................................................................................................................................................. 25

10.1.1. Route Inputs to Outputs........................................................................................................................................................................................................................26

10.1.2. Turn Off (Mute) Outputs....................................................................................................................................................................................................................... 26

10.1.3. Display Output Status............................................................................................................................................................................................................................26

10.1.4. Resetting to Factory Defaults............................................................................................................................................................................................................. 27

11. Troubleshooting ....................................................................................................................................................................................................................................................................27

11.1. General Troubleshooting Guidelines..............................................................................................................................................................................................................27

11.2. No Signal from Source to any Display ............................................................................................................................................................................................................28

11.3. No Signal from any Source to any Display ....................................................................................................................................................................................................28

11.4. Audio Issues.............................................................................................................................................................................................................................................................. 28

12. System Layout Chart ..........................................................................................................................................................................................................................................................29

13. Specications.......................................................................................................................................................................................................................................................................... 30

14. Contacting Tech Support ...................................................................................................................................................................................................................................................31

15. Warranty ..................................................................................................................................................................................................................................................................................31

1. PRODUCT OVERVIEW

Welcome to Binary™. This product is engineered to provide years of exceptional reliability. We appreciate your

business, and we stand committed to providing our customers with the highest degree of quality and service in the

industry.

The B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2 is a state-of-the-art HDMI matrix switcher with both

HDMI and HDBaseT outputs. It provides true matrix routing for HDMI signals. With features such as HDMI 3D

support, sophisticated EDID handling, and IR, RS-232 and Ethernet control, this product is ideal for residential

and commercial media distribution systems. The HDBaseT connection on each output extends HDMI signal and

bidirectional IR to remote rooms up to 230 feet away via Category cable.

Note: This manual covers installation and setup of the B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2 for most

applications. Some features must be congured using the Conguration Utility software. Go to the product page

for the B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2 at www.SnapAV.com and click on the Support tab to

download the Conguration Utility and manual.

2. FEATURES

• 8 HDMI inputs by (8) mirrored HDMI and HDBaseT outputs (B-520-MTRX-230-8x8)

• 6 HDMI inputs by (6) HDMI and (4) HDBaseT outputs (B-520-MTRX-230-6x4+2)

• PoC capable – HDBaseT receiver B-520-RX-230-IR can be powered via the Category cable

• Supports video resolutions up to1080p/60 36bit color

• Supports all HDMI audio formats

• Supports all HDMI 3D formats

• Sophisticated EDID handling including embedded, learned, and auto modes

• HDMI or DVI with adapter (not included)

• IR Control from integrated receiver or 3.5mm input

• Bidirectional IR passthrough when using B-520-RX-230-IR

• Home Control via IR, RS-232 and Ethernet

• PC Setup and conguration using dedicated software

• HDCP 2.0 compliant

• CEC Passthrough

3. PACKAGE CONTENTS

• 1x B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2

• 2x rack ears for mounting

• 4x screws

• 1x IR remote control

• 1x Power supply 12VDC, 16A

• 1x Installation Manual

• 1x CD-ROM

4. RECOMMENDED FOR INSTALLATION

• Phillips screwdriver (for rack ear attachment)

• Binary High Speed HDMI Cables to connect sources to B-520-MTRX-230-8x8/B-520-MTRX-230-6x4+2

HDMI inputs

• Binary HDMI cables or B-520-RX-230-IR units and Category cable installed between matrix switcher location

and displays (See section 7.6.3.1, page 10 for HDBaseT wiring recommendations)

• RJ45 connectors and termination tools (if using B-520-RX-230-IR)

• Control system to control operation of B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2

• Windows PC with Conguration Utility installed and RS-232 adapter

• Conguration Utility Manual

• Binary™ brand high-speed HDMI cables to connect the sources

5. DEVICE LAYOUT

FIGURE 1: B-520-MTRX-230-8x8 Switcher Layout (Front View)

5.1. Front Panel of the B-520-MTRX-230-8x8 Switcher

A. Power On/Off Switch

Lights up blue when power is on and lights up red when in stand-by. Can be disabled from conguration utility

software

B. Source Status LEDs

Indicates that the selected source is On and transmitting an HDMI signal

C. Output Display

Displays the last output selected

D. IR Receiver Window

IR receiver for matrix to capture commands sent by IR remote

E. Input Display

Displays the last input selected

A EDCB

5.2. Rear Panel of the B-520-MTRX-230-8x8 Switcher

FIGURE 2: B-520-MTRX-230-8x8 Switcher Layout (Rear View)

A. Power LED

Lights up red when powere is applied

B. Power Jack

+12V DC, 16A power supply connection

C. RS-232 control port (DB9)

To communicate with control system or Windows PC for serial control of matrix

D. IR Input to Room - 1 through 8 (3.5mm mono)

To connect a control system and send IR signals to displays or other devices in a room (when using an HDBaseT

receiver such as B-520-RX-230-IR)

E. System IR In

To connect a control system with 3.5mm mono IR input for matrix control

F. System All IR Out

3.5mm mono mini port, repeats all IR commands from all connected HDBaseT outputs (from IR Receiver

port of B-520-RX-230-IR).

G. IR Output to Source - 1 through 8 (3.5mm mono)

To connect IR ashers for controlling sources. These ports may be congured to route commands only from

the IR output corresponding to the HDBaseT output number (IR zone routing), or directly to the source

selected for viewing on an HDBaseT output (IR source routing). (See Conguration Utility Manual)

H. RJ45 HDBaseT Outputs - 1 through 8

Connect 568B terminated Category HDBaseT cable routed to a B-520-RX-230-IR up to 230 feet away to

feed HDMI signal to display. Output simultaneously displays the same source as the HDMI output of the same

number

I. Link LEDs -1 through 8

The green Link LEDs indicate the status of the HDBaseT connection. Off = no link; On = link is active

J. HDMI Outputs - 1 through 8

Connect HDMI cables to route to displays. Output simultaneously displays the same source as the HDBaseT

output of the same number

K. Ethernet Port

RJ45 port for connecting an ethernet Cat5e/6 cable for IP control of the B-520-MTRX-230-8x8

L. HDMI Inputs (1 through 8)

Connect HDMI cables from sources to the matrix switcher for distribution

A JD G I

B C

E F H

5.3. Front Panel of the B-520-MTRX-230-6x4+2 Switcher

FIGURE 3: B-520-MTRX-230-6x4+2 Switcher Layout (Front View)

A. Power On/Off Switch

Lights up blue when power is on and lights up red when in stand-by. Can be disabled from Conguration Utility

software

B. Source Status LEDs

Indicates that the selected source is on and transmitting an HDMI signal

C. Output Display

Displays the last output selected

D. IR Receiver Window

IR receiver for matrix to capture commands sent by IR remote

E. Input Display

Displays the last input selected

A EDCB

5.4. Rear Panel of the B-520-MTRX-230-6x4+2 Switcher

FIGURE 4: B-520-MTRX-230-6x4+2 Switcher Layout (Rear View)

A. Power LED

Lights up red when power is Applied

B. Power Jack

+12V DC, 16A power supply connection

C. RS-232 control port (DB9)

To communicate with control system or Windows PC for serial control of matrix

D. IR Input to Room - 1 through 4 (3.5mm mono)

To connect a control system and send IR signals to displays or other devices in a room (when using an HDBaseT

receiver such as B-520-RX-230-IR)

E. System IR In

To connect a control system with 3.5mm mono IR input for matrix control

F. System All IR Out

3.5mm mono mini port, repeats all IR commands from all connected HDBaseT outputs (from IR Receiver

port of B-520-RX-230-IR)

G. IR Output to Source - 1 through 6 (3.5mm mono)

To connect IR ashers for controlling sources. These ports may be congured to route commands only from

the IR output corresponding to the HDBaseT output number (IR zone routing), or directly to the source

selected for viewing on an HDBaseT output (IR source routing). (See Conguration Utility Manual)

H. RJ45 HDBaseT Outputs - 1 through 4

Connect 568B terminated Category HDBaseT cable routed to a B-520-RX-230-IR up to 230 feet away to

feed HDMI signal to display. Output simultaneously displays the same source as the HDMI output of the same

number.

I. Link LEDs -1 through 4

The green Link LEDs indicate the status of the HDBaseT connection. Off = no link; On = link is active.

J. HDMI Outputs - 1 through 6

Connect HDMI cables to route to displays. Output simultaneously displays the same source as the HDBaseT

output of the same number

K. Ethernet Port

RJ45 port for connecting an ethernet Cat5e/6 cable for IP control of the B-520-MTRX-230-6x4+2

L. HDMI Inputs (1 through 6)

Connect HDMI cables from sources to the matrix switcher for distribution

DGI

EFH

6. INSTALLATION & SETUP

6.1. Basic Installation Diagram

Complete the basic installation section to set up the matrix switcher for media distribution before completing any other

setup. Use this diagram for reference during basic installation of the matrix switcher, sources, displays and wiring.

B-520-RX-230-IR

FIGURE 5: B-520-MTRX 8x8 Installation

B-520-RX-230-IR

FIGURE 6: B-520-MTRX 6x4+2 Installation

Control System

AC Power

Projector TV TV TV

Blu-ray Player Cable/Sat Box

PC Game

Console

HDMI

HDMI HDMI

RS-232

Cat5e/6

Control System

AC Power

Projector HDTV HDTV HDTV

Blu-ray Player Cable/Sat Box

PC Game

Console

HDMI

HDMI HDMI

RS-232

Cat5e/6

6.2. Basic Instructions

These are the basic steps that must be taken to connect equipment to the inputs and outputs of the matrix

switcher and congure the system for use. See the sections listed for full information on completing each step.

1. Unpack the matrix and install it near the source equipment. (6.4. Switcher Location and Placement, page 11)

Note: Do not power the matrix switcher until it is indicated to do so.

2. Install and connect each source to an input on the matrix switcher using the shortest HDMI cable possible.

(6.5. HDMI Input Connections, page 11).

3. Install the displays and output wiring to the matrix location using HDMI cables for standard HDMI output or

Cat5e/6 if B-520-RX-230-IR receivers will be used. (6.6. Output Connections, page 12).

4. Record the inputs and outputs used in the System Layout Chart for future reference. (13. System Layout Chart,

page 30).

5. If using a control system, connect it to the appropriate port on the matrix switcher for the driver type being

used: IR, RS-232, or IP control. (6.7. Matrix Control Connections, page 11).

6. Install and congure the driver for matrix switching control into the control system processor. (6.7. Matrix

Control Connections, page 13).

7. Install the IR equipment and set up IR passthrough if using it. (6.8. IR Passthrough Installation and Setup, page

14).

8. Attach the power supplies to the matrix, sources, and displays, then power up the system.

9. Test all input and output selections for sync, reliable switching, correct audio format and video resolution. Use

the factory remote or the Matrix Conguration Utility to set up EDIDs as needed. (7. EDID Conguration, page

20).

10. Change any advanced settings in the Matrix Conguration Utility as needed to suit the installation. (8.

Advanced Setup Using the Conguration Utility, page 24).

6.3. Installation Tips

Following these tips during the installation process will help guarantee a successful installation.

• Always test every cable before use.

Field-terminated cables should be checked for continuity after termination to be sure the connectors were

installed correctly.

• Label each cable as it is installed.

This will aid in connection setup and programming, and will also make it easier to come back to a job at a later

date and immediately know what is connected where.

• Complete the System Layout Chart (page 29) in the back of the manual during installation.

Record the source connected to each input, the output number of each display, and the method of routing

signal in the chart for reference during installation and setup. Use it afterward to keep track of equipment in

use, open ports for expansion, and to help identify where to troubleshoot issues if they arise later.

• Leave an RS-232 connection easily accessible for using the Conguration Utility.

The B-520-MTRX-230-8x8 / B-520-MTRX-230-6x4+2 is equipped with many setup functions that must be

accessed by using a PC and the Conguration Utility. Leave an RS-232 cable connected during setup and

testing that can easily be connected to the PC. If the matrix is being controlled by RS-232, disconnect the

control system while using the Utility.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Binary Commutatore a matrice

Binary

Binary B-660-MTRX-4X4 Manuale utente

Binary

Binary B-100-HDMATRIX-4X4 Manuale utente

Binary

Binary B-660-MTRX-8X8 Manuale utente

Binary

Binary B-120-HDMATRIX-4x4 Guida rapida

Binary

Binary B-660-MTRX-4X4 Manuale utente

Binary

Binary 120 Series Manuale utente

Binary

Binary B-500-MTRX-230-4x4 Manuale utente

Binary

Binary B-200-AVDMATRIX-8X8 Manuale utente

Binary

Binary B-500-MTRX-230-8x16 Manuale utente

Binary

Binary B-210-HDMATRIX-4X4 Manuale utente

Manuali Commutatore a matrice popolari di altre marche

Broadcast Tools

Broadcast Tools SS 8.2 Manuale utente

Altimium

Altimium MATF32 Manuale utente

ALFAtron

ALFAtron ALF-MUK44N Manuale utente

Monoprice

Monoprice Blackbird 15377 Manuale utente

Kramer

Kramer XL 3216VS Manuale utente

PTN

PTN FMX12 Manuale utente

CYP

CYP nT15GX01 Manuale utente

Kramer

Kramer VP-2x2 Manuale utente

Kramer

Kramer Sierra Video 6432V5xl Manuale utente

TESmart

TESmart HMA0402A40 Manuale utente

Octava

Octava HD4XSTPMX Manuale utente

Intelix

Intelix FLX-88 Istruzioni operative

Kramer

Kramer LASSEN XL 3232S Manuale utente

Roland

Roland XS-1HD Manuale utente

Kramer

Kramer VS-66HDCPxl Manuale utente

Atlona

Atlona AT-HDMI-22M Manuale utente

Link

Link HD8X8 Manuale utente

AMX

AMX AVS-OP-2020-117 Istruzioni e ricette