BIQU Thunder Manuale utente
Table of Content
One: Product Overview............................................................................. 1
Two: Tools and Supplies ........................................................................... 3
Three: Assembly........................................................................................ 4
3.1 Machine Assembly ....................................................................... 4
3.2 Machine Wiring............................................................................ 7
Four: User interface .................................................................................. 9
Five: Specification ................................................................................... 15
Six: Feature Overview ............................................................................. 16
Seven: Smart Phone Connection ............................................................ 18
Eight: Slicer.............................................................................................. 23
Nine: Connect and Print.......................................................................... 28
9.1 Repetier-Host Installation .......................................................... 28
9.2 Connect Printer with Repetier-Host........................................... 29
Ten: Trouble Shooting............................................................................. 34
Eleven: Important Information............................................................... 36
Shenzhen Bigtree Technology Co.,Ltd
1
One: Product Overview
1. z-axis aluminum
extrusion
9. extruder module
2. cable chain
10. y-axis aluminum
extrusion
3. filament
11. x-axis aluminum
extrusion
4. circular connector
12. bearing
5. x-axis limit switch
13. spring
6. heated bed
14. support plate
7. fine adjust nut
15. screen
8. system unit
16. reset button
Shenzhen Bigtree Technology Co.,Ltd
2
1. screw rod
8. extruder stepper
2. motor coupling
9. y-axis synchronous
wheel
3. z-axis stepper
motor
10. y-axis stepper motor
4. support plate
11. AC plug
5. teflon tube
12. on/off switch
6. one-touch fitting
13. x-axis stepper
7. extruder
14. filament holder
Shenzhen Bigtree Technology Co.,Ltd
3
Two: Tools and Supplies
Please make sure you receive all the tools and supplies, contact your
seller as soon as possible if anything is missing.
Shenzhen Bigtree Technology Co.,Ltd
4
Three: Assembly
3.1 Machine Assembly
Please make sure the machine is not damaged during shipping. If there is
any problem, contact the seller as soon as possible. If the machine is in
good condition, and no tools or supplies are missing, feel free to start
installing your printer.
Step one: place the aluminum extrusion (2) such that they are facing
toward the front of the printer (1), use the bolts from bag A1 (black
M5*25 bolt) (3) to fasten both aluminum extrusions.
Step two: check that the aluminum extrusion (1) is secured, make sure (2)
and (3) are orientated correctly according to the picture.
Step three: twist couplings of both z-axis steppers at the same time so
that the x-axis rail can slide in smoothly.
Step four: make sure the aluminum extrusion is facing the front (similar to
step one), use the hardware in bag A1 (black M5*25 bolts, M5 washers)
to secure the top aluminum extrusion.
Shenzhen Bigtree Technology Co.,Ltd
5
Step five: extruder stepper installation. Make sure you place the stepper
(1) with the correct orientation as highlighted with the red box. Four
threaded holes are facing the aluminum plate (2). Use then bag of
hardware labeled as A2 (black M3*10 bolt) (3). Tighten the stepper as
shown.
Step six: find the x-axis slider (1), use bag A3 hardware (black M4*8 bolt),
and tighten up extruder module (2).
Step seven: place the extruder wiring harness on the right, use the bolts
in bag A4 to secure the cable chain from left side (2) to right side (3), this
way is easier.
Shenzhen Bigtree Technology Co.,Ltd
6
Step eight: slightly loosen the nuts near plate (1) and filament holder (2),
fasten on the aluminum extrusion.
Step nine: slightly loosen the nuts near the T shape plate (1), fasten the
plate on the aluminum extrusion.
Note: refer to picture 10 about how to assemble parts on the aluminum
extrusion.
Shenzhen Bigtree Technology Co.,Ltd
7
3.2 Machine Wiring
Step one: screw the golden one-touch fitting (1) to the extruder and
connect the filament sensor cable (2) to the extruder.
Step two: connect the extruder cable E0 (1) to the extruder, connect x-
axis stepper cable and limit switch cable to (2) and (3).
Step three: connect the circular connector (1) on to the correct location
showed in the picture, align the connector before plugging in, then fasten
the connector.
Shenzhen Bigtree Technology Co.,Ltd
8
Step four: connect Z axis endstop cable (1) with endstop from inner side.
Step five: plug in the extruder cable (1).
Step six: wire the cable to the z-axis stepper motors (1) (2).
Indice
Altri manuali BIQU Stampante 3D
