Bitspower BPTA-XYZ-LITE Manuale utente
P 1
BPTA-XYZ-LITE 示範組裝說明書
繁中文
V4
主件說明
...........................................1個
...........................................1個
...........................................2支
...........................................4支
.......................1個
水箱
馬達
支架
螺絲
大4PIN供電線材
配件內容
本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，
產品顏色與配件以實物為準。
出水孔
入水孔
1
3
2
4
35
1
2
3
4
5
P 2
水箱與水泵不可拆解！一經拆解即不保固。
組裝完成樣式
A 電源負極 -
B 電源正極 +
C 轉速信號
D 調速信號
A B C D
水泵規格
額定電壓：12V DC
功 耗：8.4W
最大流量：460±15%L/h
噪 音：≦24dBA
PWM：有
MTBF：≦15,000 小時
供電與馬達
1
組裝示範（自由創作）
2
馬達除了可由主機板供電外，亦可透
過轉接線由電源供應器直接供電。
參考步驟一
參考步驟二(部分組件需另購)
5
4
3
P 3
單一水路串聯接法：
水路分配
4
DRGB燈效啟動
6
填水注意事項
5
1.出水孔A銜接其它水冷配件入水孔（或者選擇銜接B、C其一孔）。
2.若選擇直接串連B/C孔，則B、C中另一孔銜接其它配件入水孔。
3.串接其它配件後由其出水孔銜接D/E其中一孔。
4.選擇D/E孔其一為填水孔。
雙水路併聯接法：
1.其一水路由出水孔A銜接其它水冷配件入水孔。
2.串接該配件後由其出水孔銜接D、E其中一孔。
3.另一水路選擇有B/C孔其一孔為入水或出水（自由分配），再銜接回
該水路。
4.選擇D/E孔其一為填水孔。
→燈條插頭可依方向順序接上主機板
與主板同步燈光效果，或選擇串接
BP-CADRGBY1(不包括)與其它DRGB
燈效配件串連，共享燈效控制端。
主板
選擇喜好的水冷濃縮液顏色，以純淨水調合，由”填水孔”注入至水箱九分滿，接著利用”24PIN跳線開關”
啟動電源，讓水路中的空氣集中至水箱排出，再依水量繼續添加至水箱九分滿左右即可。
（24PIN跳線開關用途：需無經主板開啟ATX電源時， 使電源直接開啟供電。）
注意：Bitspower 建議消費者使用蒸餾水、純凈水，加入Bitspower的染劑作為水冷液使用；如客戶自
行選購的水冷液導致電鍍層剝落、水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致
漏水等及其它不可抗力之問題時，消費者自行承擔相關產品責任。
未注水前，請勿啟動水泵電源。
B
A
C
D
E
P 4
整機示範
7
主件說明(需另購)
BPTA-CPUMS-SKIA
BPTA-VG2080RDB
BPTA-NLSS360-F2PBC
BPTA-FX1812NT-1D
BP-WTP-C95E
BP-WTP-C61F
BP-WTP-C62G
BP-WTP-C64H
BPTA-90REI
BPTA-DOTFH1420J
K.......... 1PCS
............ 1PCS
.... 1PCS
......... 3PCS
.................... 1PCS
..................... 1PCS
..................... 1PCS
..................... 1PCS
......................... 8PCS
........ 10PCS
...... 5PCSBP-NCCLT14AC-L500
A
B
C
D
E
F
G
H
I
JK
P 5
BPTA-XYZ-LITE Installation Guide
English
V4
Main
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
............................1PCS
......................................1PCS
..................................2PCS
..........................4PCS
....1PCS
Water Tank
Pump
Bracket
M3x8 Screw
3PIN/4PIN Transfer4PIN
Accessories
1
2
3
4
5
出水孔
入水孔
1
3
2
4
35
P 6
The water tank and pump can’t
be disassembled! Once disassem-
bled, there is no guarantee.
Assembly Finished Sample
A Negative electrode -
B positive electrode +
C Speed signal
D Speed control signal
A B C D
Pump Spec.
Rated voltage：12V DC
Power consumption：8.4W
Maximum flow：460±15%L/h
Noise：≦24dBA
PWM：Yes
MTBF：≦15,000 hours
Power Supply and Pump
1
Assembly Demonstration (Free Creation)
2
Except the motherboard, pump can
be powered from the power supply
via a patch cord.
5
Step 1
Step 2(additional purchases)
4
3
P 7
Single series connection：
DRGB Light Effect Start
6
Water Distribution
4
Water Filling Safeguard
5
1.The water goes from outlet A to the inlet of other water cooling parts. (Or
A choose to connect B or C)
2.If choose to connect to B, and then C has to connect to the inlet of the
other water cooling parts.
3.And then connect to the D or E.
4.Choose D or E as the hole for filling water.
B
A
C
D
E
Double waterway connection：
1.The water goes from outlet A to the inlet of other water cooling parts.
2.And then from the outlet of the other water cooling parts to D or E.
3.Choose B or C as the inlet or outlet , connect to other water cooling parts
(Free chosen) as a single finished water loop .
4.Choose D or E as the hole for filling water.
→The light bar plug can be connected to the
motherboard, in synchronization with the
motherboard lighting effect. Or select the
serial connection BP-CADRGBY1(Not included)
and other DRGB lighting effect accessories to
share the lighting effect control.
Choose your desired dye color and mix it with pure distilled water. Pour the water mix into the reservoir via the water filling hole. Once the reservoir is
90% full, turn on the power supply for the pump to run and let the air exit the loop. Turn off the power supply when the reservoir is near empty. Repeat
until all the air has exited the loop. (In order to power the pump only, connect the power switch connector to the 24 pin cable of the power supply. This
will allow the power supply to bypass the motherboard and make the pump work alone.)
Notice:
Bitspower recommends that consumers add the Bitspower dye to distilled water or
purified water for their water-cooling liquid. If the consumer chooses different
water-cooling liquids, the resulting impurities may cause peeling of the coating on some
of the hardware, water channels blockage by built-up residue, improper operation of the
water pump, water tank tube breakage, and o-rings deformation leading to leakage.
Any issues related to the use of inappropriate water-cooling liquid will be the responsi-
bility of the consumer.
Do not turn on the pump if the reservoir is empty.
主板
P 8
Sample
7
Accessories(additional purchases)
BPTA-CPUMS-SKIA
BPTA-VG2080RDB
BPTA-NLSS360-F2PBC
BPTA-FX1812NT-1D
BP-WTP-C95E
BP-WTP-C61F
BP-WTP-C62G
BP-WTP-C64H
BPTA-90REI
BPTA-DOTFH1420J
K.......... 1PCS
............ 1PCS
.... 1PCS
......... 3PCS
.................... 1PCS
..................... 1PCS
..................... 1PCS
..................... 1PCS
......................... 8PCS
........ 10PCS
...... 5PCSBP-NCCLT14AC-L500
A
B
C
D
E
F
G
H
I
JK
P 9
BPTA-XYZ-LITE 示范组装说明书
简中文
V4
本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，
产品颜色与配件以实物为准。
主件說明
...........................................1个
...........................................1个
...........................................2支
...........................................4支
.......................1个
水箱
馬達
支架
螺丝
大4PIN供电线材
配件內容
出水孔
入水孔
1
3
2
4
35
1
2
3
4
5
P 10
供电与马达
1
水箱与水泵不可拆解！一经拆解即不保固。
组装完成样式
水泵规格
额定电压：12V DC
功 耗：8.4W
最大流量：460±15％L / h
噪 音：≦24dBA
PWM：有
平均无故障工作时间：≦15,000小时
组装示范（自由创作）
2
水泵除了可由主机板供电外，亦可透
过转接线由电源供应器直接供电。
A 电源负极 -
B 电源正极 +
C 转速信号
D 调速信号
A B C D
5
参考步骤一
参考步骤二(部分组件需另购)
Altri manuali Bitspower Hardware per computer
Bitspower
Bitspower TA-DIO16-RGB Manuale utente
Bitspower
Bitspower Premium Cubiod Reservoir 150 D5 Manuale utente
Bitspower
Bitspower BP-TEKIT-3080FE Manuale utente
Bitspower
Bitspower BP-VG3090TIST Manuale utente
Bitspower
Bitspower touchaqua Sedna O11D Manuale utente
Bitspower
Bitspower r Premium Cubiod Reservoir 200 Manuale utente
Bitspower
Bitspower BP-RAMS22D-D5 Manuale utente
Bitspower
Bitspower GeForce RTX 3090 Founders Edition Manuale utente
Bitspower
Bitspower BP-VG3090CFA Manuale utente
Bitspower
Bitspower Titan Series Manuale utente
Bitspower
Bitspower BPTA-XYZ-RES-PWM Manuale utente
Bitspower
Bitspower Premium Cubiod Reservoir 150 Manuale utente
Bitspower
Bitspower BP-RAMS44-D5 Manuale utente
Bitspower
Bitspower GALAX GeForce RTX 3090 HOF Series Manuale utente
Bitspower
Bitspower O11DXL Manuale utente
Bitspower
Bitspower Sedna 570X Manuale utente
Bitspower
Bitspower BP-RAMCD5-LN2 Manuale utente
Bitspower
Bitspower BP-LPM2HS-BK Manuale utente
Bitspower
Bitspower CR802 Manuale utente
Bitspower
Bitspower BP-RAMS44D-D5 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
