BK TECHNOLOGIES KAA0608A Manuale utente
KAA0608A
User Guide
A. General
The KAA0608A is a cable assembly used for testing KNG-P/KNG-Ps series radios. This cable is
compatible with Cobham/Aeroflex 3920 only. If using HP8920, please use KAA0608.
B. The Kit
RF Coax Cable – 1ea.
Double Banana
Plug Adapter -1 ea.
BNC Male Binding Post - 2 ea.
Cable Assy
17001-31084-200_Ver. 11-17 | BK Technologies
C. Set-Up
1. Turn on the Aeroflex 3920.
2. Highlight “BK KNG Autotest”, then press “SELECT” as shown in Figure 2.
Figure 2
3. The test script will load up.
4. Radio IP box should have “10.250.46.5” if not enter this IP as shown in Figure 3.
Figure 3
5. Highlight the field just below IP Address box.
6. Press “Select” then a menu will show up as shown in Figure 4.
Figure 4
7. Choose the type of test for the radio under test.
8. Press “Select”.
27001-31084-200_Ver. 11-17 | BK Technologies
D. Connections:
1. Connect the “Mic” BNC to “FUNCTION GEN/DEMOD OUT” port of the Aeroflex 3920.
2. Connect the Accessory Plug (DIN) into the “MIC/ACC” port of the Aeroflex 3920 as shown in Figure 5.
Figure 5
3. Connect the two “Banana to BNC” binding post to Audio In 1 and 2 as shown in Figure 6.
Figure 6
4. Connect “Double Banana to BNC” to “Audio In” binding posts on the Aeroflex 3920 as shown in Figure 7.
Figure 7
37001-31084-200_Ver. 11-17 | BK Technologies
5. Connect the Audio/Speaker out coax from the test kit to the “Double Banana to BNC” adapter connected to
Aeroflex 3920 “Audio In” as shown in Figure 8.
Figure 8
6. Connect RF Coax Cable to “T/R” port of the Aeroflex 3920 and to the radio RF antenna out as shown in
Figure 5.
7. Connect the USB Cable to Aeroflex 3920 USB port (see Fig. 5) and the side connector USB.
E. Operation:
1. Select Test Type
1.1.From the pull-down, select “Portable Test”, “Portable Align & Test”, “Portable Test (No Audio) or
“Portable Align & Test (No Audio)”.
2. Full Align and Test.
2.1. To perform the full alignment and test, highlight “Select All” and all the alignment items will be selected
as shown in Figure 9.
Figure 9
2.2. Press the button corresponding to “START” to begin the alignment.
3. Individual Testing.
3.1.If individual testing is desired, then highlight “RESET ALL” then highlight the individual test items to run.
3.2.Press “START”.
47001-31084-200_Ver. 11-17 | BK Technologies
Technical Service Support - Customer Service
BK Technologies
7100 Technology Drive
Melbourne, FL 23904
(800) 422-6281
www.BKTechnologies.com
57001-31084-200_Ver. 11-17 | BK Technologies
Indice
Altri manuali BK TECHNOLOGIES Apparecchiature di prova
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
