Black Box 5 Manuale utente
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
© Copyright 1998. Black Box Corporation. All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A
computing device in accordance with the specifications in Subpart J of Part 15
of FCC rules, which are designed to provide reasonable protection against
such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at his own expense will be required
to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
TRADEMARKS USED IN THIS MANUAL
PS/2, AT and IBM are registered trademarks of International Business
Machines Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property
of the trademark owners.
FCC AND IC STATEMENTS, TRADEMARKS
1
POW-R-BOOT 5
NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas
antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas
para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones
de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como
sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por
los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes
de calor como radiadores, registros de calor, estufas u otros aparatos
(incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique en
el aparato.
2
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que
no sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo
a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos
de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo
no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos
no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio
en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
3
POW-R-BOOT 5
Contents
Chapter Page
1. Specifications ............................................................................................. 5
2. Introduction ............................................................................................... 7
2.1 General Overview ................................................................................ 7
2.2 Features ............................................................................................... 7
2.3 The Pow-R-Boot 5 Illustrated ............................................................. 8
3. Installation ................................................................................................ 11
3.1 Setting the Rate Switch ..................................................................... 11
3.2 Rackmounting the Unit .................................................................... 12
3.3 Connecting the Master Device ......................................................... 12
3.4 Connecting the Switched Devices .................................................... 14
3.5 Powering Up the System ................................................................... 14
4. Operation ................................................................................................. 15
5. Troubleshooting ...................................................................................... 17
5.1 Common Concerns ........................................................................... 17
5.2 Calling Black Box .............................................................................. 18
5.3 Shipping and Packaging ................................................................... 19
4
5
CHAPTER 1: Specifications
Compliance — FCC Class A, IC Class/classe A
Interfaces — (2) RS-232 compatible serial (DTE): (1) IBM PS/2,
AT style, (1) proprietary
Protocol — Asynchronous
Data Format — Receive: Either 7 data bits, even or odd parity, and
1 stop bit, or 8 data bits, no parity, 1 stop bit
(autosensing);
Transmit: 8 data bits, no parity, 1 stop bit (fixed)
Flow Control — None
Data Rate — 9600, 2400, 1200, or 300 bps (user-selectable)
Maximum
Distance — 50 ft. (15.2 m) from control port to master device
User Controls — Commands from master device;
(2) Rear-mounted:
(1) 4-position configuration DIP switch,
(1) ON/OFF rocker switch
Indicators — (7) Front-mounted LEDs: (1) POWER ON, (1) DATA
INPUT, and (5) BOOT IN PROGRESS
Connectors — Data: (2) Rear-mounted: (1) DB9 female for
connection to PC or modem, (1) RJ-11 female for
connection to Port Manager Switch;
AC Power Inlet:
SWI020A: (Nondetachable power cord with
NEMA 5-15P plug);
SWI020AE: IEC 320 male;
1. Specifications
POW-R-BOOT 5
Connectors
(continued) — AC Power Outlets:
SWI020A: (5) NEMA 5-15R sockets;
SWI020AE: (5) IEC 320 female
Leads Supported — On DB9 connector: Pins 1, 2, 3, 4, 5, and 7 (RLSD
[DCD], RD, TD, DTR, SGND, and RTS respectively);
On RJ-11 connector: Pins 1, 2, 3, 5, and 6 (DTR,
SGND, TD, RD, and CTS respectively)
Input Power — SWI020A: 115-VAC, 60 Hz directly from outlet
through nondetachable 6-ft. (1.5-m) power cord;
SWI020AE: 230-VAC, 50 Hz directly from outlet
through detachable power cord (not included)
No-Load (Standby)
Current Draw
(Consumption) — SWI020A: 500 mA;
SWI020AE: 250 mA
Output Power — SWI020A: 115-VAC, 60 Hz, up to 5 amps on one
outlet (but not more than 10 amps total for all
outlets);
SWI020AE: 230-VAC, 50 Hz, up to 2.5 amps on one
outlet (but not more than 5 amps total for all
outlets);
Temperature
Tolerance — 32 to 122 F (0 to 50˚C)
Humidity
Tolerance — 20 to 80% noncondensing
Size — 1.8" (1U) H x 17"W x 6.5"D (4.4 x 43.2 x 6.5 cm);
when rackmount brackets are added, the unit is
19" (48.3 cm) wide
Weight — 5 lb. (2.3 kg)
6
7
CHAPTER 2: Introduction
2.1 General Overview
The Pow-R-Boot 5 (PRB 5) is a convenient tool you can use to reboot as
many as five AC-powered devices from a remote location. Normally, when
a computer or peripheral device locks up, it must be manually reinitialized
by on-site personnel. But when you plug pieces of equipment into the PRB 5,
you can send a command from a remote site—even from half a world away
across a modem link—to reset any or all of them by toggling AC power
ON and OFF.
The Pow-R-Boot 5’s RS-232 Control Port will accept commands (in the form
of ASCII character strings) to select the desired port and initiate the reboot
routine. You can connect the PRB 5 to a master or control device such as a
PC or one of our Port Manager Switches, either directly (with a serial cable)
or indirectly (through a modem).
The unit also has a DIP switch you can set to (a) select the appropriate
data rate for communication between the unit and the master device,
(b) choose a short or long reboot cycle, and (c) enable or disable
“Quiet Mode.”
If the unit receives and carries out a command, it will respond with
a “PRB OK” message so that you can verify proper communication with the
master device. (You can turn off these messages by enabling Quiet Mode.)
2.2 Features
• Remotely toggle AC power to any of the unit’s five separate outlets.
• Connect a PC to the RS-232 Control Port either directly or indirectly
(across a modem link).
• Directly connect one of our Port Manager Switches (product codes
SW545A and SW546A) to the Control Port.
• Set the length of the “downtime” or “offtime” part of the reboot cycle
(that is, how long the unit denies power to the rebooting device before
restoring it).
• Receive status messages from the unit (or, if you don’t want these, enable
Quiet Mode).
2. Introduction
POW-R-BOOT 5
2.3 The Pow-R-Boot 5 Illustrated
2.3.1 T
HE
F
RONT
P
ANEL
Both models of the Pow-R-Boot 5 share the same front panel, which is shown
in Figure 2-1 below.
Figure 2-1. The front panel of the Pow-R-Boot 5.
The unit’s front-panel LED indicators have these functions:
•POWER ON: Lights when the Pow-R-Boot 5 is receiving AC power
and is therefore ready to receive commands.
•DATA INPUT: Flashes when the Pow-R-Boot 5 receives commands
through one of its Control Ports.
•BOOT IN PROGRESS 1 through 5: Light when a reboot cycle
is in progress at the Pow-R-Boot 5’s corresponding AC outlet.
8
Pow-R-Boot 5
9
2.3.2 T
HE
R
EAR
P
ANEL
The two versions of the Pow-R-Boot 5 have slightly different rear panels,
as shown in Figures 2-2 and 2-3 below.
Figure 2-2. The rear panel of the 115-VAC model
of the Pow-R-Boot 5 (SWI020A).
Figure 2-3. The rear panel of the 230-VAC model
of the Pow-R-Boot 5 (SWI020AE).
The rear-panel components have these functions:
•AC Outlets 1 through 5: The devices whose rebooting you want to
control must be plugged into these outlets. On the 115-VAC model
(SWI020A), the outlets are North American standard NEMA 5-15R
sockets; on the 230-VAC model (SWI020AE), they are international
standard IEC 320 female connectors. Each outlet can deliver up to
5 amps (SWI020A) or 2.5 amps (SWI020AE) of current, but the total
current drawn from all five outlets must not exceed 10 amps (SWI020A)
or 5 amps (SWI020AE). See Section 3.4 for more information.
•Control Area: The master device from which you want to want to send
reboot commands should be connected to one of the two Control Ports in
this area: the DB9 female connector labeled “RS232” if the master device
is a PC or modem, or the RJ-11 connector labeled “CPM” if the master
device is one of our Port Manager Switches (product code SW545A
or SW546A). See Section 3.3 for more information.
The Control Area also contains a 4-position DIP switch labeled
“RATE”for setting the data rate and other parameters as described
in Section 3.1.
CHAPTER 2: Introduction
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Black Box Unità di controllo
Black Box
Black Box VIDEOPLEX 4000 Manuale utente
Black Box
Black Box Receive Module for ServSwitch KV1702C Manuale utente
Black Box
Black Box LMC5113C Manuale utente
Black Box
Black Box JHN2021A Manuale utente
Black Box
Black Box T568B Manuale utente
Black Box
Black Box PS590A Manuale utente
Black Box
Black Box SOHO 7-Zone Audio Module Manuale utente
Black Box
Black Box MTU200CF-N64 Manuale utente
Black Box
Black Box JHN2050A Manuale utente
Black Box
Black Box EVSW-240-100-60 Manuale utente
Black Box
Black Box ServLINK ACRPWR Manuale utente
Black Box
Black Box JHN2046A Manuale utente
Black Box
Black Box LRA1204C Manuale utente
Black Box
Black Box JHN2047A Manuale utente
Black Box
Black Box ServSwitch DTX Control Manuale utente
Black Box
Black Box JHN2400A Manuale utente
Black Box
Black Box FollowMe LH3800A Manuale utente
Black Box
Black Box V.11 LS Manuale utente
Black Box
Black Box ServSwitch KV1400A Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
