Black Box LB532A-L Manuale utente

LB532A-L

LB532A-R

DeeSel.1 Industrial Ethernet Extender Local and Remote Units,

G.SHDSL 2-Wire 5.7 Mbps

Extend industrial Ethernet connections cost-effectively up to 4.3 miles

over existing twisted pair cable.

724-746-5500 | blackbox.com

Page 2

Black Box Ethernet Extenders

TABLE OF CONTENTS

1. General Information .....................................................................................9

1.1 Features ..............................................................................................9

1.2 Description.......................................................................................... 9

1.3 Power Input Connector....................................................................... 9

2. Configuration ............................................................................................. 10

2.1 Hardware (DIP-switch) Configuration ...............................................10

2.2 DIP Switch Settings.......................................................................... 11

DIP Switch Settings: Data Rate............................................. 11

Ethernet Management Port.................................................... 14

3. Installation.................................................................................................. 16

3.1 Connecting the Interface ...................................................................16

3.2 Connecting the Ethernet Interface.................................................... 17

3.3 Connecting Power ............................................................................ 18

4. Operation................................................................................................... 19

4.1 Power-up ..........................................................................................19

4.2 LED Status Monitors......................................................................... 19

Power (Green) ....................................................................... 20

Line Link (Green)................................................................... 20

ETH Link (Green)................................................................... 20

5. Software Upgrade...................................................................................... 20

A. Specifications............................................................................................. 21

A.1 Line Rate ..........................................................................................21

A.2 Ethernet Interface .............................................................................21

A.3 Status LEDs ......................................................................................21

Power (Green) ....................................................................... 21

Line Link (Green)................................................................... 21

ETH Link (Green)................................................................... 21

A.4 Configuration ....................................................................................21

Factory Default Configuration................................................ 21

A.5 Power and Power Supply Specifications ..........................................22

A.6 Transmission Line .............................................................................22

A.7 Line Coding .......................................................................................22

A.8 Line Interface ....................................................................................22

A.9 Physical Connection .........................................................................22

A.10 Environment ......................................................................................23

724-746-5500 | blackbox.com Page 3

Table of Contents

A.11 Third Party Software Licenses ..........................................................23

B. Interface Pinouts........................................................................................ 23

B.1 Line Port ...........................................................................................23

B.2 Ethernet Port ....................................................................................23

724-746-5500 | blackbox.com

Page 4

Black Box Ethernet Extenders

RADIO FREQUENCY INTERFERENCE STATEMENTS

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO

FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested and

found to comply with the limits for a Class A computing device in accordance with the

specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection against such interference when the equipment is operated in a

commercial environment. Operation of this equipment in a residential area is likely to

cause interference, in which case the user at his own expense will be required to take

whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le Règle-

ment sur le brouillage radioélectrique publié par Industrie Canada.

724-746-5500 | blackbox.com Page 5

INSTRUCCIONES DE SEGURIDAD

(Normas Oficiales Mexicanas Electrical Safety Statement)

3. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

4. Las instrucciones de seguridad y operación deberán ser guardadas para refer-

encia futura.

5. Todas las advertencias en el aparato eléctrico y en sus instrucciones de oper-

ación deben ser respetadas.

6. Todas las instrucciones de operación y uso deben ser seguidas.

7. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de

la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

8. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

9. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

10. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a

lo descrito en las instrucciones de operación. Todo otro servicio deberá ser refer-

ido a personal de servicio calificado.

11. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera

su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o

superficie similar puede bloquea la ventilación, no se debe colocar en libreros o

gabinetes que impidan el flujo de aire por los orificios de ventilación.

12. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como

radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificado-

res) que producen calor.

13. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo

descrito en el instructivo de operación, o como se indique en el aparato.

14. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

15. Los cables de la fuente de poder deben ser guiados de tal manera que no sean

pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo par-

ticular atención a los contactos y receptáculos donde salen del aparato.

724-746-5500 | blackbox.com

Page 6

Black Box Ethernet Extenders

16. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomenda-

ciones del fabricante.

17. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

18. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

19. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derrama-

dos sobre la cubierta u orificios de ventilación.

20. Servicio por personal calificado deberá ser provisto cuando:

A. El cable de poder o el contacto ha sido dañado; u

A. Objectos han caído o líquido ha sido derramado dentro del aparato; o

A. El aparato ha sido expuesto a la lluvia; o

A. El aparato parece no operar normalmente o muestra un cambio en su desem-

peño; o

A. El aparato ha sido tirado o su cubierta ha sido dañada.

724-746-5500 | blackbox.com Page 7

Safety When Working With Electricity

SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. This

device can only be repaired by qualified

service personnel.

• Do not open the device when the power cord is con-

nected. For systems without a power switch and without

an external power adapter, line voltages are present

within the device when the power cord is connected.

• For devices with an external power adapter, the power

adapter shall be a listed Limited Power Source. The

mains outlet that is utilized to power the device shall be

within 10 feet (3 meters) of the device, shall be easily

accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable

used meets all applicable standards for the country in

which it is to be installed.

• For AC powered devices which have 3 conductor power

plugs (L1, L2 & GND or Hot, Neutral & Safety/Protective

Ground), the wall outlet (or socket) must have an

earth ground.

• For DC powered devices, ensure that the interconnecting

cables are rated for proper voltage, current, anticipated

temperature, flammability, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazard-

ous voltages present regardless of whether the device is

powered ON or OFF. PSTN relates to interfaces such as

telephone lines, FXS, FXO, DSL, xDSL, T1, E1, ISDN,

Voice, etc. These are known as “hazardous network volt-

ages” and to avoid electric shock use caution when

working near these ports. When disconnecting cables

for these ports, detach the far end connection first.

• Do not work on the device or connect or disconnect

cables during periods of lightning activity.

WARNIN

724-746-5500 | blackbox.com

Page 8

Black Box Ethernet Extenders

In accordance with the requirements of council

directive 2002/96/EC on Waste of Electrical and

Electronic Equipment (WEEE), ensure that at

end-of-life you separate this product from other

waste and scrap and deliver to the WEEE col-

lection system in your country for recycling.

This device contains no user serviceable parts.

This device can only be repaired by qualified

service personnel.

This device is NOT intended nor approved for

connection to the PSTN. It is intended only for

connection to customer premise equipment.

Electrostatic Discharge (ESD) can damage

equipment and impair electrical circuitry. It

occurs whenelectronic printed circuit cards are

improperly handled and can result in complete

or intermittent failures. Do the following to pre-

vent ESD:

• Always follow ESD prevention procedures

when removing and replacing cards.

• Wear an ESD-preventive wrist strap, ensur-

ing that it makes good skin contact. Connect

the clip to an unpainted surface of the chas-

sis frame to safely channel unwanted ESD

voltages to ground.

• To properly guard against ESD damage and

shocks, the wrist strap and cord must oper-

ate effectively. If no wrist strap is available,

ground yourself bytouching the metal part of

the chassis.

ARNIN

724-746-5500 | blackbox.com Page 9

1. GENERAL INFORMATION

Thank you for your purchase of this Black Box product. This product has been thor-

oughly inspected and tested and is warranted for one year for parts and labor. If any

questions or problems arise during installation or use of this product, contact Black

Box Technical Support at 724-746-5500 or info@Black Box.com.

1.1 FEATURES

• High speed extension with speeds up to 5.696 Mbps

• Two 2-wire line connections via built-in RJ-45 ports (C1 and C2)

• 10- or 100Base-T and full or half-duplex Ethernet port for direct connection of

four Ethernet devices

• Extends Ethernet upto 3.4 miles (5.48 km) using 24 AWG/0.5mm wire (192 kbps

speed) per hop

• DIN Rail mount

• -40 to 85ºC operating temperature

1.2 DESCRIPTION

The Black Box LB532A-L and LB532A-R Industrial Ethernet Extenders are easy to use

and take advantage of existing copper twisted-pair infrastructure to connect Ethernet

networks or devices at high speeds over long distances. The LB532A-L and LB532A-R

deliver speeds up to 5.696 Mbps with distances ranging from 3.5 to 5.48 km (2.2 to 3.4

miles) on standard 0.5 mm (24 AWG) voice-grade twisted pair. Whether setting up a

private network backbone to a corporate LANs or remote office or connecting network

enabled devices such as PCs, digital sensors or IP cameras—Black Box Ethernet

Extenders offer the best combination of speed and distance in the industry. The

LB532A-L and LB532A-R temperature specs allow for operation at -40 to 85ºC.

1.3 POWER INPUT CONNECTOR

The LB532A-L and LB532A-R come with an external AC universal power supply. (For

additional specifications and details on power and power supply, see Appendix A.5 on

page 22.)

• The power connection to the LB532A-L and LB532A-R is a terminal block

• Rated voltage: 5 VDC

724-746-5500 | blackbox.com

Page 10

Black Box Ethernet Extenders

• Rated current: 1 A DC

Figure 1. Terminal block power connection

• Output from power supply: 5 VDC, 2A regulated (± 5%)

• Input to power supply: universal input 100–240 VAC 50/60 Hz 0.3A

2. CONFIGURATION

You can configure the LB532A-L and LB532A-R only through the hardware configura-

tion via DIP switches.

2.1 HARDWARE (DIP-SWITCH) CONFIGURATION

The only configurable parameter is the data rate, set by DIP switches S4-2 through

S4-8 (see Table 2 on page 11). All other DIP switches should remain in the OFF posi-

tion. When configuring the data rate, set the DIP switches to the desired rate before

applying power to the LB532A-L or the LB532A-R.

NOTE: Factory Default Configuration: 5.696 Mbps (DIP are all OFF)

The external AC adapter shall be a listed limited

power source that incorporates a disconnect

device and shall be positioned within easy

reach of the operator. Ensure that the AC power

cable meets all applicable standards for the

country in which it is to be installed, and that it

is connected to a wall outlet that has

earth ground.

Table 1: LB532A-M configurable parameters

Parameter Description Possible

Values

Data Rate/

Timeslots Defines the number of timeslots. The data

rate is calculated by the equation:

data rate = timeslots x 64k.

1-72 timeslots

Power

+ -

CAUTIO

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Black Box Estensione

Black Box

Black Box IC408A Manuale utente

Black Box

Black Box AC555A Manuale utente

Black Box

Black Box ICS02A Manuale utente

Black Box

Black Box CAT5 ClassWork Plus Multiloop Manuale utente

Black Box

Black Box 10BASE-T MiniHub Manuale utente

Black Box

Black Box AC1070A Manuale utente

Black Box

Black Box ServSwitch ACU5200A Manuale utente

Black Box

Black Box LMC5178A Manuale utente

Black Box

Black Box LB522A-KIT Manuale utente

Black Box

Black Box EMERALD PE DUAL-HEAD Manuale utente

Black Box

Black Box 4KDPKVMXT-100M Manuale utente

Black Box

Black Box ACU5050A Manuale utente

Black Box

Black Box IC101A Manuale utente

Black Box

Black Box ACU2500A-R3 Manuale utente

Black Box

Black Box LR0201A-KIT Manuale utente

Black Box

Black Box LB308A Manuale utente

Black Box

Black Box ServSwitch II ACS250A Manuale utente

Black Box

Black Box IC553A Manuale utente

Black Box

Black Box AC230A Manuale utente

Black Box

Black Box IC247A Manuale utente

Black Box

Black Box ServSwitch ACU3001A Manuale utente

Black Box

Black Box ACU5800A Wizard DP Istruzioni per il montaggio

Black Box

Black Box LB200A Manuale utente

Black Box

Black Box AC1021A-XMIT Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente