Black Box 5000 series Manuale utente

Series 5000 Bridge/Router

PPP Menu Reference Manual

LR5100A-T, LR5200A-R2

5500149-10 equivalent to 5500073-11

PPP Menus

Throughout this manual, information that is presented by the router and entered into the router will be shown in a bordered

box, as shown here.

Screen information being displayed or entered.

Initial Router & Management Console Power-Up

The following screen information will be seen on the console connected to the router when it is first powered on:

Terminals supported:

teletype ansi, avt, ibm3101, qvt109, qvt102, qvt119, tvi925, tvi950,

vt52,vt100, wyse-50, wyse-vp

Enter terminal type:

As the terminal type is not yet defined at the very first power-up, this screen may be slightly mixed up. Enter at least one

<RETURN> (up to three if necessary) on the Network Console in order for the router to determine the baud rate of the

terminal used for the console (i.e. auto-baud) and then proceed.

Select your terminal if listed and enter its name in lower case at the prompt, or choose the terminal type teletype if your

terminal is not listed. The teletype terminal type operates in scroll mode and may be used successfully until a custom

terminal definition is created.

Menu Command Entry

Once the terminal type is specified, the MAIN (LOGIN) MENU will be displayed.

The router uses a “hotkey “ Menu. A menu option is chosen by selection of the desired option number.

Entry of parameters is from the “>“ prompt. When a parameter is required, enter the necessary string and end it with a

<Return>. If the entry is not accepted, an error message will be reported and the parameter will have to be re-entered.

Should you make an error, the <BACKSPACE> key (for most terminals) deletes the most recently entered characters.

Menus Reference Manual

Menu Structure

DEVICE: DEVxxxxxx ⇐ 12 ⇒V X.X.X

⇓

XXXX MENU

4 5 6

⇓⇓⇓

Option Value Description

1. XXXXX menu XXXXXXXXXXXX

2. XXXXX [XXXX] Description of XXXXXXXX

7 8 9

⇓ ⇓ ⇓

Enter option number, “=“ - main menu, <TAB> - previous menu

>⇐10

11 ⇒ALARM: * LAN connection established

The Menu Screens are structured with 11 primary elements:

1. Device Name

2. Software Version

3. Menu Name

4. Option Number and Option Name

5. Option Value

6. Option Description

7. Choosing an Option

8. Returning to the Main Menu

9. Returning to the Previous Menu

10. Command Prompt

11. ALARM display for a just-happened alarm event

Menus Reference Manual

Elements of the Menu Screens:

1. Device Name

A default Device Name in the format DEVxx-xx-xx is supplied by the system for each router. (xxxxxx are the last

6 digits of the MAC address of the router). The Device Name may be changed in the Device Set-Up Menu.

2. Software Version

The version of the software currently installed in the router is shown in the upper right-hand corner of each menu

display.

3. Menu Name

Each MENU is named to indicate its grouped Options..

4. Option Number and Option Name

Choosing the number for the Option makes the selection. If you prefer a command-style interface, typing the first

few unique letters of the desired Option is enough to identify the Option. Enter the selection with a <Return>.

5. Option Value

The Value of an Option may indicate several parameters—for example:

State [enabled], [disabled], [present], [not_present], ...

Setting [5 sec.], [5 min.], ...

Path “menu” indicates a sub-menu

Name [vt100], [Bridge_5], [none]

6. Option Description

This is a single-line description of the Option.

7. Choosing an Option

Select the Option by entering its number or unique first letters at the prompt.

8. Returning to the Main Menu

The equals (“=“) sign returns you to the Main Menu. (All major menu paths start at the Main Menu. If you want

to switch to the Main Menu, enter “ = “).

9. Returning to the Previous Menu

To go back to the previous higher level menu, enter a <TAB>.

10. Command Prompt >

All data entry is made at the Command Prompt.

11. ALARM display for an occurring event

The display of an ALARM notifies a viewing router manager that an event of significance has occurred. Since not

every ALARM can be viewed as it occurs, the latest 199 ALARMs are recorded and can be viewed from the

Network Events Menu.

Note: Depending on the configuration setting of this device, some options are not always displayed and some menus will

have different options. Display lines with these options are in italics in this manual. If the option may appear on the menu

screen with various numbers, the possible numbers are listed in the write up for the option, for example:

3/4 ISDN Set-Up.

Menus Reference Manual

Option Description

1. Login - Initiate operator session

2. Help - Read menu introduction

Enter option number

This is the LOGIN MENU seen when powering up a console connected to the router.

1 - Login

The Login option allows entry of the password for the router. The default password is “BRIDGE”; change it if security

is desired (see the password option of the Access menu, page 15). See the Installation & Applications Guide for

information on restoring the default password to the router.

Action to Take:

Choose the Login Option and use the default password “BRIDGE.” The characters will not be echoed on

the screen. Once the password is accepted, you will be given the expanded MAIN MENU for full access to

router management features.

If this router is being accessed by a telnet session, the operator at the console may override the telnet session by logging in

at the console. The telnet session will be locked out for 10 minutes or until the operator logs out. Telnet access may be

disabled under the Telnet Set-Up menu, page 17. Any attempts to connect via telnet while the router is under console

control will be registered in the Network Events log.

2 - Help

The Help option provides a brief description of menu format and usage.

Menus Reference Manual: Main Menu

Main Menu

MAIN MENU

Option Value Description

1. Configuration menu - Define operating parameters

2. Statistics menu - Device LAN and WAN statistics

3. Diagnostics menu - Access troubleshooting tools

4. Network events menu - View network event history

5. Logout - End operator session

6. Help - Read menu introduction

Enter option number

The MAIN MENU is a starting and ending point for management of the router. This menu allows access to menus and

provides the Logout Option. Options 1-4 are major paths. To switch major paths, return to the MAIN MENU by entering

“=“.

1 - Configuration

The Configuration option takes you to the Configuration Menu, where all the various router parameters are defined.

Take this path to define the operating parameters of the terminal used for the router console.

2 - Statistics

The Statistics option takes you to the Statistics Menu, where statistics can be examined to evaluate router, LAN, and link

performance.

3 - Diagnostics

The Diagnostics option takes you to the Diagnostics Menu, where special diagnostic functions can be used to analyze

LAN, link, and router problems.

4 - Network Events

The Network Events option takes you to the Network Events Menu, where the 199 latest Alarms can be examined.

5 - Logout

The Logout option terminates your session and secures the router. The next user must log in and enter the correct

password to view or change the router configuration.

6 - Help

The Help option provides a brief, one-screen description of menu format and usage.

Menus Reference Manual: Configuration Menu

Configuration Menu

CONFIGURATION MENU

Option Value Description

1. Access set-up menu - Establish access parameters

2. LAN set-up menu - Define LAN environment

3. WAN set-up menu - Configure WAN operation

4. Applications set-up menu - Configure Internet applications

5. Bridging set-up menu - Define bridging environment

6. IP routing set-up menu - Define IP routing environment

7. IPX routing set-up menu - Define IPX environment

8. Filter set-up menu - Filter operations

Enter option number, “=“ - main menu, <TAB> - previous menu

The CONFIGURATION MENU provides paths to menus for configuration of this router.

1 - Access Set-Up

The Access Set-up option takes you to the Access Set-Up Menu, where passwords, names, dates, and times are set and

viewed. From this menu, you can save or restore the router configuration and connect to another router in the network

of routers.

2 - LAN Set-Up

The LAN Set-up option takes you to the LAN Set-Up Menu, where the parameters for the Local Area Network

configuration are configured.

3 - WAN Set-Up

The WAN Set-up option takes you to the WAN Set-Up Menu, where the Wide Area Network links are configured and

controlled.

4 - Applications Set-Up

The Applications Set-up option takes you to the Applications Set-up Menu, where the internet connection management

applications for SNMP, DHCP, Firewalls, Network Address Translation and Syslog may be accessed.

5 - Bridging Set-Up

The Bridging Set-up option takes you to the Bridging Set-Up Menu, where the parameters for bridging are configured.

Menus Reference Manual: Configuration Menu

6 - IP Routing Set-Up

The IP Routing Set-up option takes you to the IP Routing Set-Up Menu, where the parameters for IP routing are

configured. IP routing may be enabled or disabled in this menu.

7 - IPX Routing Set-Up

The IPX Routing Set-up option takes you to the IPX Routing Set-Up Menu, where the parameters for IPX routing are

configured. IPX routing may be enabled or disabled in this menu.

8 - Filter Set-Up

The Filter Set-up option takes you to the Filter Set-Up Menu, where you can create filters based on protocol types and

custom specifications.

Menus Reference Manual: Access Set-Up Menu

Access Set-Up Menu

ACCESS SET-UP MENU

Option Value Description

1. Terminal set-up menu - Define operator's console

2. Device set-up menu - Set security/time/names

3. Telnet set-up menu - Set up remote communications

4. Load FLASH set-up menu - Prepare for software update

5. Console menu - Dump/restore configuration from console

6. Hardware status - Display hardware information

7. TFTP access [disabled] - Allow TFTP configuration saves/loads

Enter option number, “=“ - main menu, <TAB> - previous menu

The ACCESS SET-UP MENU provides options for saving and restoring the router configuration as well as paths to menus

for terminal, device, and remote access configuration.

1 - Terminal Set-Up

The Terminal Set-up option takes you to the Terminal Set-Up Menu, where the terminal parameters used for the router

console are selected.

2 - Device Set-Up

The Device Set-up option takes you to the Device Set-Up Menu, where the device name, password, dates, and times are

set and viewed.

3 - Telnet Set-up

The Telnet Set-up option takes you to the Telnet Access Menu, where you can connect to another router in the network

of routers.

4 - Load FLASH Set-Up

The Load FLASH Set-up option takes you to the Load FLASH Set-Up Menu, where you can update the software in this

device using TFTP or console Z-modem transfers.

Note: this operation cannot be performed from a secondary IP address.

Menus Reference Manual: Access Set-Up Menu

5 - Console

The Console option takes you to the Console Menu, where the present configuration may be dumped to the console

computer for storage or a stored configuration uploaded from the console computer.

6 - Hardware Status

The Hardware Status option displays the status of the router hardware.

Hardware Status

Boot Code version : 51B1.4.1.4 System Code revision : 7a0

Boot Code revision : 0 Service reference : 0/0

RAM size : 8 MB ROM size : 2 MB

MAC check code : b9876d23

LAN interface type : 10BaseT MAC address : 02-03-04-05-06-07

LAN2 interface type : 10BaseT, MAC address : 02-03-04-05-06-07

Module types : ( 1) BRI ST ( 2) BRI ST

CPU type : 68EH360

CPU speed : 25 Mhz

Compression : enabled

Boot Code version The software boot code version currently installed in this router. This is the

number that is displayed in the upper right of the menu screens when in console

load mode.

Boot Code revision The software boot code revision number currently installed in this router. A

control number for tracking minor software revisions.

System Code revision The system code software revision number currently installed in this router.

Service Reference Internal factory reference number.

MAC Address The MAC Address of the LAN port for this router.

MAC Check Code Check code used for feature upgrades.

RAM size The amount of RAM in this router.

ROM size Indicates the size of the FLASH EEPROM installed.

Altri manuali per 5000 series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Black Box Router di rete

Black Box

Black Box LB611A Manuale utente

Black Box

Black Box LR9601A Manuale utente

Black Box

Black Box LR9501A Manuale utente

Black Box

Black Box LB8418A Manuale utente

Black Box

Black Box LPB5028A Manuale utente

Black Box

Black Box Version 1.0 Manuale utente

Black Box

Black Box WRT4002A Manuale utente

Black Box

Black Box LB8415A-US Manuale utente

Black Box

Black Box LB611A Manuale utente

Black Box

Black Box WRT750A Manuale utente

Black Box

Black Box InvisaPC DTX1000-T Manuale utente

Black Box

Black Box LPH1006A-R2 Manuale utente

Black Box

Black Box LBS3041AE Manuale utente

Black Box

Black Box LW001A Manuale utente

Black Box

Black Box LBU2090 Manuale utente

Black Box

Black Box LR9601A Manuale utente

Black Box

Black Box ME550A-35 Manuale utente

Black Box

Black Box LB9030A-R2 Manuale utente

Black Box

Black Box VOE212 Manuale utente

Black Box

Black Box LDM-MR128 Manuale utente

Black Box

Black Box IC469A Manuale utente

Black Box

Black Box VOE241 Manuale utente

Black Box

Black Box LRA001A-R2 Manuale utente

Black Box

Black Box LR0002A-BSDN Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza