Black Box RM044 Manuale utente
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
© Copyright 2000. Black Box Corporation. All rights reserved.
VPN: ISBBRM044
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
JULY 2000
RM044 RM430A
RM330A-R3 RM431
RM331 RM432
RM332A RM630A
RM349A RM631A
RM378
Aluminum Distribution Racks
Aluminum Distribution Rack Raceways
Center Weight Shelves
CONTENTS
1
Contents
1. Aluminum Distribution Racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1 Available Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 What You’ll Need to Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Aluminum Distribution Rack Raceways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Available Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 What You’ll Need to Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Center Weight Shelves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Available Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 What You’ll Need to Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRADEMARKS USED IN THIS MANUAL
Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
ALUMINUM DISTRIBUTION RACKS, RACEWAYS, AND ACCESSORIES
2
1. Aluminum Distribution Racks
1.1 Available Models
The following models are available:
• Black Aluminum Distribution Rack, 47" (24U), 10/32 tapped holes (part number RM332A)
• Mill Aluminum Distribution Rack, 66" (35U), 10/32 tapped holes (part number RM349A)
• Black Aluminum Distribution Rack, 84" (45U), 10/32 tapped holes (part number RM330A-R3)
• Black Aluminum Distribution Rack, 84" (45U), 12/24 tapped holes (part number RM630A)
• Mill Aluminum Distribution Rack, 84" (45U), 10/32 tapped holes (part number RM430A)
• Mill Aluminum Distribution Rack, 84" (45U), 12/24 tapped holes (part number RM631A)
1.2 What’s Included
Make sure you have the following parts before assembling the Rack.
• (2) vertical upright channels
• (2) base angles
• (2) top angles
• (12) 1⁄2"-13 x 1 hex-head bolts
• (12) 1⁄2" lockwashers
1.3 What You’ll Need to Supply
• 3⁄4" socket or wrench
1.4 Installation Instructions
STEP 1: Attach the top angle to the vertical upright channels. (See Figure 1-1.)
A. Lay the vertical upright channels on edge so the tapped holes face you and the floor. Be sure that open
sides of the upright channels face each other.
B. Align the holes in the top angle with the corresponding holes in the vertical uprights. The formed leg of
the top angle should be facing you.
C. Install the two hex-head bolts and lockwashers. Finger-tighten only.
CHAPTER 1: Aluminum Distribution Racks
3
Figure 1-1. Step 1: Attaching the Top Angle to the Vertical Channel Uprights.
Top Angle
Vertical Upright
Channel
Bolt
Lockwasher
ALUMINUM DISTRIBUTION RACKS, RACEWAYS, AND ACCESSORIES
4
STEP 2: Attach the base angles to the vertical upright channels. (See Figure 1-2.)
A. Leaving the vertical upright channels on edge, align the holes in the base with the corresponding holes in
each upright channel. The long leg of the base should be facing you.
B. Install four hex-head bolts and lockwashers. Finger-tighten only.
C. Turn the vertical upright assembly over (rotate 180°) and repeat steps A and B. Finger-tighten only.
Figure 1-2. Step 2: Attaching the Base Angles to the Vertical Upright Channels.
Vertical Upright
Channel
Vertical Upright
Channel
Bolts
Lockwashers
Base
Angle
Base Angle
CHAPTER 1: Aluminum Distribution Racks
5
STEP 3: Final tightening. (See Figure 1-3.)
A. Stand the frame upright.
B. Square the unit using a level or a carpenter’s square.
C. Tighten all bolts using a socket wrench or a wrench.
Figure 1-3. Step 3: Final Tightening.
STEP 4: Secure the frame to the floor.
All frames should be bolted to the floor or to an equally stabilizing and secure surface. Determine the desired
location and secure the frame.
STEP 5: Equipment installation.
Your rack is now ready for installing equipment and panels.
Top Angle
Vertical Upright
Channel Vertical Upright
Channel
Bolt
Bolts
Bolts
Bolt
Base Angle
ALUMINUM DISTRIBUTION RACKS, RACEWAYS, AND ACCESSORIES
6
2. Aluminum Distribution Rack
Raceways
2.1 Available Models
The following models are available:
• Mill Aluminum Distribution Raceway for RM349A (part number RM378)
• Black Aluminum Distribution Raceway for RM330A-R3 and RM630A (part number RM044)
• Mill Aluminum Distribution Raceway for RM430A and RM631A (part number RM432)
2.2 What’s Included
Make sure you have the following parts before installing the Aluminum Distribution Rack Raceway.
• (1) Aluminum Distribution Rack Raceway • (6) 1⁄2-13" lockwashers
• (6) 1⁄2-13 x 1" hex-head bolts • (6) 1⁄2" hexnuts
2.3 What You’ll Need to Supply
•3⁄4" socket or wrench
2.4 Installation Instructions
NOTE
This Rack Raceway attaches to each networking frame with 2 bolts, lockwashers, and
hexnuts. After you’ve properly installed the Rack, you’ll have 2 extra bolts,
lockwashers, and hexnuts left over.
A. Align the holes in the Aluminum Distribution Rack Raceway with the holes in the networking frames and
attach them with the hex-head bolts, lockwashers, and hexnuts and tighten. (See Figure 2-1 on the next
page.)
B. Pull the knob on the cable gates to remove them from the Rack. Re-attach by pushing the knob in until it
locks.
CHAPTER 2: Aluminum Distribution Rack Raceways
7
Figure 2-1. Aluminum Distribution Rack Raceway.
Hex-head Bolt
Lockwasher
Hexnut
Aluminum Distribution
Rack Raceway
Questo manuale è adatto per i seguenti modelli
10
Indice
Altri manuali Black Box Rack e supporto
Black Box
Black Box RM202 Manuale utente
Black Box
Black Box RM260 Manuale utente
Black Box
Black Box RM155A-R2 Manuale utente
Black Box
Black Box RM110A Manuale utente
Black Box
Black Box WMD-24PMOUNT-U Manuale utente
Black Box
Black Box RM427 Manuale utente
Black Box
Black Box RM110A Manuale utente
Black Box
Black Box RM220A Manuale utente
Black Box
Black Box RM970A Manuale utente
Black Box
Black Box KVXLC-RMK Manuale utente
Black Box
Black Box Agility Manuale utente
Black Box
Black Box ServCenter RF535A Manuale utente
Black Box
Black Box RMT385 Manuale utente
Black Box
Black Box RM050A-R3 Manuale utente
Black Box
Black Box RM140A-R2 Manuale utente
Black Box
Black Box NetRack RM500A-R2 Manuale utente
Black Box
Black Box RM069A Manuale utente
Black Box
Black Box WMD12-2425-PQU Manuale utente
Black Box
Black Box RM7006 Manuale utente
Black Box
Black Box RMT701 Manuale utente
