Black Box NetRack RM500A-R2 Manuale utente
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
© Copyright 2000. Black Box Corporation. All rights reserved.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
JUNE 2000
RM500A-R2 RM505A-R2
RM501-R2 RM506-R2
RM502 RM507
RM503-R2 RM508-R2
NetRack
What You Should Have Received
Please take a moment to make sure that you received everything that’s included with your order. Each product is
described below.
RM500A-R2: (1) NetRack, black. The Rack is 85"H x 26"W x 32"D (215.9 x 66 x 81.3 cm). It consists of a welded
frame with 2 sets of adjustable rails, a full-length steel rear door with a lock, and 2 perforated
shelves. It also has vented, lift-off side panels, a removable top panel, an open bottom for
wire/cable access, and a locking plexidoor.
RM501-R2: (1) Top fan panel, black.
RM502: (2) Bottom-mount tower shelves, black. (For a complete list of the included hardware, see page 2.)
RM503-R2: (1) 12-gauge-steel caster base with four 3-inch non-locking casters, black.
RM505A-R2: (1) NetRack, beige. The Rack is 85"H x 26"W x 32"D (215.9 x 66 x 81.3 cm). It consists of a welded
frame with 2 sets of adjustable rails, a full-length steel rear door with a lock, and 2 perforated
shelves. It also has vented, lift-off side panels, a removable top panel, an open bottom for
wire/cable access, and a locking plexidoor.
RM506-R2: (1) Top fan panel, beige.
RM507: (2) Bottom-mount tower shelves, beige. (For a complete list of the included hardware, see page 2.)
RM508-R2: (1) 12-gauge-steel caster base with four 3-inch non-locking casters, beige.
NETRACK
1
The NetRack
These fully welded and assembled racks are constructed of heavy 12-gauge steel. The mounting angles, also
made of 12-gauge steel, are tapped with #10-32 thread in the E.I.A. RS 310-D universal pattern. There’s ample
space inside the frame sides for cabling, so large bundles of wire and cable fit without a problem. Plus, there’s a
locking door with a “slam latch” that provides quick access and security. And the doors can easily be changed
from left- to right-opening with a quick-release pin.
Standard knockouts for
cables or conduit
Removable top panel for
cable entry and exit
Mounting angles
adjust to any depth
within the frame
Open bottom
panel
1⁄2-13 weldnut for
levelers or 3⁄8"
diameter anchor
bolts (4 places)
Frames may be
bolted to the floor
Frames may be
joined together for
modular use
Easy-lift handles on
the side panels with
locking feature
Vented side panels
“snap” into place
Vents
NETRACK
2
Bottom-Mount Tower Shelves (RM502, RM507)
The following items are included with the RM502 or RM507.
Table 1. Items included with the RM502 or RM507
Key Description Quantity
1 Support plate 4
21⁄4-20 x 1⁄2" hexbolt 8
2A 1⁄4-20 x 1⁄2" carriage bolt 8
31⁄4-20 hexnut 8
4 Slide bracket 4
5 Slide assembly 4
6 10-32 x 3⁄8" panhead screw (included with slide) 8
7 10-32 hexnut (included with slide) 8
8 10-32 x 5⁄8" cuphead screw 16
9 Shelf assembly 2
You must supply the following tools:
•3⁄8" nutdriver or socket
•7⁄16" socket and ratchet
•7⁄16" end wrench
NOTE
Shelves may be installed to slide out toward the front or the rear of the cabinet,
whichever you prefer.
1. Attach support plates (item 1) to the cabinet base. Make sure that the flange is oriented as shown in
Figure 1, and attach it using 1⁄4-20 x 1⁄2" hexbolts (item 2) or 1⁄4-20 x 1⁄2" carriage bolts (item 2A) and
1⁄4-20 hexnuts (item 3). If the unit has round holes, use item 2. If the unit has square holes, use item 2A.
Tighten the hardware securely. Repeat for remaining plates.
NETRACK
3
Figure 1. Attaching support plates to the cabinet base.
2a. Loosely attach the slide bracket (item 4) to the rear of the slide (item 5) as shown below, using two 10-32 x
3⁄8" panhead screws (item 6) and two 10-32 hexnuts (item 7). Do not tighten at this time.
Figure 2. Attaching the slide bracket to the rear of the slide.
2b. Extend the slide/bracket assembly so that it will extend around the outside of the support plates installed
in step 1. Attach the slide/bracket assembly to support plates with four 10-32 x 5⁄8" cuphead screws (item 8)
and tighten securely. (Keep the slide/bracket assembly tight against the side of the support plate when
tightening.)
2c. Tighten the screws and hexnuts installed in step 2a.
2d. Repeat 2a, 2b, and 2c for the remaining slides.
1
2
3
4
5
8
6
7
NETRACK
4
3a. Extend the inner slide members of slides to the front of the unit until they lock in place. Take the shelf
assembly (item 9) and carefully insert slide members attached to the inside of the shelf into extended slide
members. Slide the drawer all the way to the rear of the cabinet to engage.
Figure 3. Sliding the drawer into the cabinet.
3b. Test the shelf by extending and retracting to assure proper engagement.
TRADEMARKS
Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
9
Engage slide members attached
inside shell at factory to slide
members on frame
Extend inner slide members until
they lock in position
Questo manuale è adatto per i seguenti modelli
7
Indice
Altri manuali Black Box Rack e supporto
Black Box
Black Box WMD12-2425-PQU Manuale utente
Black Box
Black Box RM110A Manuale utente
Black Box
Black Box RM050A-R3 Manuale utente
Black Box
Black Box RM110A Manuale utente
Black Box
Black Box WMD-24PMOUNT-U Manuale utente
Black Box
Black Box RMT029 Manuale utente
Black Box
Black Box RM044 Manuale utente
Black Box
Black Box RM427 Manuale utente
Black Box
Black Box RM220A Manuale utente
Black Box
Black Box Freedom Rack Plus Manuale utente
Black Box
Black Box MicroRACK RM216 Manuale utente
Black Box
Black Box RM390A-R2 Manuale utente
Black Box
Black Box JPM407A-R2 Manuale utente
Black Box
Black Box RM260 Manuale utente
Black Box
Black Box RM970A Manuale utente
Black Box
Black Box Rackmount Computer Monitor Mount Manuale utente
Black Box
Black Box RM155A-R2 Manuale utente
Black Box
Black Box RMK19K Manuale utente
Black Box
Black Box ServCenter RF535A Manuale utente
Black Box
Black Box RM202 Manuale utente
