Black BLK-HDPTZ12 Manuale utente

BLK-HDPTZ12 2 Megapixel 12x

HD-SDI / HDcctv PTZ Dome Camera

User Manual

Product: BLK-HDPTZ12

Please read this manual before using your camera, and always follow the instructions

for safety and proper use. Save this manual for future reference.

BLK-HDPTZ12_CM

1/21/13

REGULATORY NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.”

LEGAL NOTICE

Observint Technologies (Observint) products are designed to meet safety and performance standards with the use

of specic Observint authorized accessories. Observint disclaims liability associated with the use of non-Observint

authorized accessories.

The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly

prohibited by law.

Observint makes no representations concerning the legality of certain product applications such as the making,

transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We

encourage you to check and comply with all applicable local, state, and federal laws and regulations before

engaging in any form of surveillance or any transmission of radio frequencies.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks

and names or their products. Observint disclaims any proprietary interest in trademarks and trade names other than

its own.

No part of this document may be reproduced or distributed in any form or by any means without the express written

permission of Observint.

11000 N. Mopac Expressway, Building 300, Austin, TX 78759

For Sales and Support, please contact your distributor.

iii2MP 12X PTZ HD-SDI/HDcctv Dome Camera

Table of Contents

Precautions ..............................................................................v

SECTION 1 Introduction .......................................................................1

1.1 What’s in the box ....................................................................1

1.2 System conguration .................................................................2

1.2.1 RS-485 network termination ......................................................3

SECTION 2 Installation ........................................................................4

2.1 General Guidelines ...................................................................4

2.2 Install the mounting bracket ..........................................................4

2.3 Set the camera hardware conguration switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.4 Attach the camera module to the mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

SECTION 3 Software Setup - Operating Guide ....................................................12

3.1 Getting Started .....................................................................12

3.1.1 Accessing the MAIN MENU [95] + [Preset] / [Menu] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.1.2 Editing TITLE ..................................................................13

3.2 MAIN MENU ........................................................................14

3.3 SYSTEM SETUP menu ................................................................14

3.3.1 INFO – System Information ......................................................15

3.3.2 REBOOT menu ..................................................................15

3.3.3 INITIALIZE menu ................................................................16

3.3.4 Entering a PASSWORD ...........................................................17

3.4 DISPLAY SETUP Menu ................................................................17

3.4.1 LANGUAGE menu ...............................................................18

3.4.2 OSD SETUP menu ...............................................................18

3.4.3 PRIVACY ZONE SETUP menu ......................................................19

3.4.4 IMAGE SETUP menu .............................................................20

3.4.5 MOTION DETECTION (MD) menu ..................................................20

3.4.6 RESOLUTION SETUP menu ........................................................21

3.5 CAMERA SETUP menu ...............................................................22

3.5.1 FOCUS/ZOOM SETUP ............................................................22

3.5.2 WB SETUP (white balance setup) menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3.5.3 AE SETUP (auto exposure setup) menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.5.4 D/N SETUP (day and night setup) menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

3.5.5 ADVANCED SETUP menu .........................................................26

TABLE OF CONTENTS

3.6 DOME MOTION SETUP menu ..........................................................27

3.6.1 GENERAL SETUP menu ..........................................................27

3.6.2 MOTION SETUP menu ...........................................................28

3.6.3 HOME ACTION SETUP menu ......................................................29

3.6.4 CALIBRATION SETUP menu .......................................................30

3.7 PRESET SETUP menu .................................................................30

3.8 PATTERN SETUP menu ...............................................................32

3.9 TOUR SETUP menu ..................................................................33

3.10 SCAN SETUP (auto scan) menu ........................................................34

3.11 ALARM SETUP menu .................................................................35

SECTION 4 OSD Menu Structure Reference .......................................................37

4.1 CAMERA SETUP submenus ............................................................37

4.2 DISPLAY SETUP submenus ............................................................38

4.3 DOME MOTION SETUP submenus ......................................................39

4.4 Miscellaneous submenus .............................................................40

4.5 SYSTEM SETUP submenus ............................................................40

SECTION 5 Specications .....................................................................41

APPENDIX A Troubleshooting ...................................................................43

APPENDIX B Camera Dimensions ................................................................44

APPENDIX C Pelco™ Protocol Function List ........................................................45

v2MP 12X PTZ HD-SDI/HDcctv Dome Camera

PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS

Precautions

• Any changes or modications to this camera which are not expressly approved by the party responsible for compliance could void

the user’s authority to operate the camera.

• A regulated 24 Vac 2.5 A power supply is recommended for use with this camera for best picture and the stable operation. An

unregulated power supply can cause damage to the camera. Any use of an unregulated power supply will void the product

warranty.

• Use this camera with a CCTV quality monitor with a 75 Ω input impedance. If your monitor is congured for high impedance,

then adjust it accordingly before connecting the camera to it.

• Never point the camera towards the sun or any bright or reected light. Very bright light may cause smear on the picture and

possible damage to the camera imager.

• Do not remove the product label. It is important for warranty service.

Important Safety instructions

• Read and follow the instructions contained manual. Keep this manual for future reference.

• Heed all warnings.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the instructions included herein.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers).

• Protect the power cord from being walked on or pinched.

• Only use attachments and accessories specied by your dealer.

• Use only with the cart, stand, tripod, or bracket specied by the manufacturer or sold with the camera. When a cart is used,

use caution when moving the cart/camera combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualied service personnel. Servicing is required when the apparatus is damaged, such as a faulty power

supply cord or plug, or objects have fallen into the unit, it does not operate normally, or has been dropped.

NOTES

12MP 12X PTZ HD-SDI/HDcctv Dome Camera

SECTION 1: INTRODUCTION

SECTION 1

Introduction

These high denition indoor/outdoor PTZ (pan / tilt / zoom) dome camera feature a 1/3” CMOS 2.1 megapixel sensor that provides

full HD quality 1080p @ 30 fps. Features include:

• Autofocus, high resolution integrated color camera

• 120x Zoom (12x optical, 10x digital)

• IP66 (weatherproof) rated outdoor operation

• WDR (wide dynamic range)

• BLC/HSBLC

• DNR (digital noise reduction)

• Day & Night (auto / BW / color)

• Pan 360° endless rotation

• Tilt 180° vector scan available

• 210 preset positions (except short-cut command)

• 8 auto scan

• 8 pattern

• 8 tours consist of presets, patterns and scans

• 4 alarm input (o / N.C. / N.O.) and 1 alarm output (o / N.C. / N.O.)

• User programmable setting (preset, auto scan, pattern, tour, home function, alarm action, etc)

• Programmable PTZ speed: Proportional to zoom ratio, changeable preset speed

• Multi-language OSD support

• Private mask zone support

• Standard protocol including Pelco-D / Pelco-P

• Up to 255 camera IDs

• RS-485 receiver

• 24 Vac powering

• IP66 rating (weatherproof)

1.1 What’s in the box

Your camera includes the following:

• PTZ camera module

• Wall mount bracket

• User manual (this document)

• Lag bolts, washers and plastic wall anchors (4 each)

• Screws and plastic wall anchors (alternate mounting hardware, 4 each)

• 24 Vac terminal plug, RS-485 terminal plug, and an alarm terminal plug

• L-wrench

SECTION 1: INTRODUCTION

Camera module

Camera

inside dome

Camera

Dome

Assembly

Cable

access

Camera module

retention screw

Mounting bracket

Conduit port

Camera module

cable loop

A 2 foot camera module drop cable is routed into the mounting bracket and attached to trunk cables there. Trunk cables for HD-SDI

video, composite video, power, alarms and RS-485 can be routed either through conduit connected to the conduit port, or in

through the base of the mounting bracket.

1.2 System conguration

The following illustration shows a typical PTZ camera network that includes multiple cameras, a PTZ controller, a video distribution

box (J-box), multiplexer, DVR/VCR, and a monitor.

32MP 12X PTZ HD-SDI/HDcctv Dome Camera

SECTION 1: INTRODUCTION

In the diagram above, video output from each camera on the network is applied to a distribution box (J-box), then connected to a

multiplexer, DVR/VCR, and monitor.

The PTZ features of the cameras are controlled across an RS-485 network with a PTZ controller. Up to 99 BLK-HDPTZ12 cameras can

be attached to a single RS-485 network.

1.2.1 RS-485 network termination

RS-485 networks are usually congured as a series of point-to-point (multidrop) nodes, a line or a bus (star or ring congured

networks are not recommended). Termination resisters are required for devices at the ends of the bus to reduce signal reections

in the network that can cause data corruption. The value of each termination resistor should be equal to the cable characteristic

impedance, typically 120 ohms for twisted pair cable. In the following illustration of network examples, the grayed devices are

congured to apply termination to the RS-485 bus.

SECTION 2: INSTALLATION

SECTION 2

Installation

2.1 General Guidelines

• The camera drop cable connects to the network cables (RS-485, alarm in/out, HD-SDI video out, 24 Vac power leads) inside

the mounting bracket provided with the camera. A cable access cover on the underside of the mounting bracket allows access

to cable connections, and to the composite video monitoring drop.

• Network cables can be routed into the mounting bracket through conduit attached to the underside of the mounting bracket,

or through the mounting bracket mounting.

• Hardware conguration switches (for camera ID, video mode, RS-485 protocol, etc.) are accessible when the camera dome

cover is removed.

• Position the camera in a location where it provides the best visibility of your surveillance targets, and is dicult to tamper with

or damage.

• Use extra care to avoid damaging the camera dome cover.

2.2 Install the mounting bracket

1. Using the mounting bracket as a template, mark the location of the mounting screw/wall anchor holes. Although bolts,

washers and wall anchors are included with the camera, these may not be appropriate for the surface where the bracket will

be attached. Always use the appropriate mounting hardware to ensure that the bracket is securely attached to the mounting

surface.

Mounting bracket

Cable access

cover

Conduit

connector

Wall anchor

Bolt and washer

Indice

Altri manuali Black Telecamera di sicurezza

Black

Black BLK-CPV700RH Manuale utente

Black

Black BLK-CCD203VS2 Manuale utente

Black

Black BLK-HDM1IR Manuale utente

Black

Black BLK-HDC10M Manuale utente

Black

Black BLK-CPD700 Manuale utente

Black

Black BLK-CWD208VH2 Manuale utente

Black

Black BLK-CDS205NS2 Manuale utente

Black

Black BLK-CDS105NH Manuale

Black

Black BLK-CWS108NH Manuale

Black

Black BLK-CDS205NH Manuale utente

Black

Black BLK-CPT235VH Manuale utente

Black

Black BLK-CWD208VH Manuale utente

Black

Black BLK-CCP141VH Manuale utente

Black

Black BLK-CCD203VS Manuale utente

Black

Black BLK-CCP141VH Manuale utente

Black

Black BLK-CCP143VH Manuale utente

Black

Black BLK-HD33IR Manuale utente

Black

Black BLK-CWD208VH Manuale utente

Black

Black DIGIOP BLK-CWS208NH Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente