Bosch DIP-2040-00N Manuale utente
DIVAR IP 2000
DIP-2040-00N, DIP-2042-2HD, DIP-2042-4HD
en Quick Installation Guide
Table of contents
1Safety precautions 4
1.1 General safety precautions 4
1.2 Electrical safety precautions 7
1.3 ESD precautions 8
1.4 Operating precautions 9
2System overview 10
2.1 Device views 10
2.2 LED description - front panel 13
2.3 LAN port LED description - rear panel 14
3System setup - first steps 15
3.1 Introduction 15
3.2 Setup instruction 15
3.3 Starting the application 16
3.4 Using Configuration Wizard 17
4Additional documentation and client software 27
5End-user license agreement (EULA) 28
DIVAR IP 2000 Table of Contents | en 3
Bosch Sicherheitssysteme GmbH 2013.09 | V4 | DOC
Safety precautions
Observe the safety precautions in this chapter.
General safety precautions
Follow these rules to ensure general safety:
– Keep the area around the system clean and free of clutter.
– Place the chassis top cover and any system components
that have been removed away from the system or on a table
so that they won't accidentally be stepped on.
– While working on the system, do not wear loose clothing
such as neckties and unbuttoned shirt sleeves, which can
come into contact with electrical circuits or be pulled into a
cooling fan.
– Remove any jewelry or metal objects from your body, which
are excellent metal conductors that can create short
circuits and harm you if they come into contact with printed
circuit boards or areas where power is present.
!
Warning!
Interruption of mains supply:
Voltage is applied as soon as the mains plug is inserted into the
mains socket.
However, for devices with a mains switch, the device is only
ready for operation when the mains switch (ON/OFF) is in the
ON position. When the mains plug is pulled out of the socket,
the supply of power to the device is completely interrupted.
1
1.1
4en | Safety precautions DIVAR IP 2000
2013.09 | V4 | DOC Bosch Sicherheitssysteme GmbH
!
Warning!
Removing the housing:
To avoid electric shock, the housing must only be removed by
qualified service personnel.
Before removing the housing, the plug must always be removed
from the mains socket and remain disconnected while the
housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any
repairs.
!
Warning!
Power cable and AC adapter:
When installing the product, use the provided or designated
connection cables, power cables and AC adaptors. Using any
other cables and adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use
of UL or CSA-certified cables (that have UL/CSA shown on the
code) for any other electrical devices.
!
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an
explosion. Always replace empty batteries with batteries of the
same type or a similar type recommended by the manufacturer.
Handle used batteries carefully. Do not damage the battery in
any way. A damaged battery may release hazardous materials
into the environment.
Dispose of empty batteries according to the manufacturer's
instructions.
DIVAR IP 2000 Safety precautions | en 5
Bosch Sicherheitssysteme GmbH 2013.09 | V4 | DOC
!
Warning!
Handling of lead solder materials used in this product may
expose you to lead, a chemical known to the State of California
to cause birth defects and other reproductive harm.
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET
protection measures must be carried out correctly.
When handling electrostatically sensitive printed circuits,
grounded anti-static wrist bands must be worn and the ESD
safety precautions observed.
Notice!
Installation should only be carried out by qualified customer
service personnel in accordance with the applicable electrical
regulations.
Disposal
Your Bosch product has been developed and
manufactured using high-quality materials and
components that can be reused.
This symbol means that electronic and electrical
devices that have reached the end of their working
life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already
in place for used electrical and electronic
products. Please dispose of these devices at your
local communal waste collection point or at a
recycling center.
6en | Safety precautions DIVAR IP 2000
2013.09 | V4 | DOC Bosch Sicherheitssysteme GmbH
Electrical safety precautions
Basic electrical safety precautions should be followed to protect
you from harm and the system from damage:
– Be aware of the locations of the power on/off switch on the
chassis as well as the room's emergency power-off switch,
disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from
the system.
– Do not work alone when working with high voltage
components.
– Power should always be disconnected from the system
when removing or installing main system components, such
as the motherboard or memory modules. When
disconnecting power, you should first turn off the system
and then unplug the power cords from all the power supply
modules in the system.
– When working around exposed electrical circuits, another
person who is familiar with the power-off controls should
be nearby to switch off the power if necessary.
– Use only one hand when working with powered-on
electrical equipment. This is to avoid making a complete
circuit, which will cause electrical shock. Use extreme
caution when using metal tools, which can easily damage
any electrical components or circuit boards they come into
contact with.
– The power supply power cords must include a grounding
plug and must be plugged into grounded electrical outlets.
The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical
shock.
– Mainboard replaceable soldered-in fuses: Self-resetting PTC
(Positive Temperature Coefficient) fuses on the mainboard
must be replaced by trained service technicians only. The
1.2
DIVAR IP 2000 Safety precautions | en 7
Bosch Sicherheitssysteme GmbH 2013.09 | V4 | DOC
new fuse must be the same or equivalent as the one
replaced. Contact technical support for details and
support.
!
Caution!
Mainboard Battery: There is a danger of explosion if the
onboard battery is installed upside down, which will reverse its
polarities. This battery must be replaced only with the same or
an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the
manufacturer's instructions.
ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with
different electrical charges coming into contact with each other.
An electrical discharge is created to neutralize this difference,
which can damage electronic components and printed circuit
boards. The following measures are generally sufficient to
neutralize this difference before contact is made to protect your
equipment from ESD:
– Do not use mats designed to decrease electrostatic
discharge as protection from electrical shock. Instead, use
rubber mats that have been specifically designed as
electrical insulators.
– Use a grounded wrist strap designed to prevent static
discharge.
– Keep all components and printed circuit boards (PCBs) in
their antistatic bags until ready for use.
– Touch a grounded metal object before removing the board
from the antistatic bag.
– Do not let components or printed circuit boards come into
contact with your clothing, which may retain a charge even
if you are wearing a wrist strap.
1.3
8en | Safety precautions DIVAR IP 2000
2013.09 | V4 | DOC Bosch Sicherheitssysteme GmbH
– Handle a board by its edges only. Do not touch its
components, peripheral chips, memory modules or
contacts.
– When handling chips or modules, avoid touching their pins.
– Put the mainboard and peripherals back into their antistatic
bags when not in use.
– For grounding purposes, make sure your computer chassis
provides excellent conductivity between the power supply,
the case, the mounting fasteners and the mainboard.
Operating precautions
The chassis cover must be in place when the system is operating
to assure proper cooling. Out of warranty damage to the system
can occur if this practice is not strictly followed.
Note:
Please handle used batteries carefully. Do not damage the
battery in any way. A damaged battery may release hazardous
materials into the environment. Do not discard a used battery in
the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management
agency to dispose of your used battery properly.
1.4
DIVAR IP 2000 Safety precautions | en 9
Bosch Sicherheitssysteme GmbH 2013.09 | V4 | DOC
System overview
The DIVAR IP 2000 system is an affordable, easy to use all-in-one
recording and management solution for network surveillance
systems of up to 16 channels. All channels are pre-licensed.
Running the full Bosch recording solution including the Video
Streaming Gateway to integrate 3rd party cameras,
DIVAR IP 2000 is an intelligent IP storage device that provides
both, a professional video recording solution and ease of
operation.
DIVAR IP 2000 is a 4-bay mini tower unit that combines
advanced management and state-of-the-art recording
management into a single cost-effective, plug and play IP
recording appliance for IT-minded customers which are seeking
for a state-of-the-art “second generation” NVR recording
solution.
DIVAR IP 2000 utilizes a highly energy efficient, embedded
design at a very affordable price which nevertheless boasts
Bosch quality through-and-through.
Easy to install and operate, DIVAR IP 2000 features wizard-
based set-up and centralized configuration to reduce installation
times. All components are pre-installed and pre-configured.
Simply connect to the network and turn on the unit —
DIVAR IP 2000 is ready to begin recording straight out-of-the-
box.
DIVAR IP 2000 features front-swappable SATA-II hard drives
providing up to 8 TB of gross storage capacity. All system
software is pre-installed and pre-activated — creating an out-of-
the-box ready-to-use video recording appliance. DIVAR IP 2000
utilizes Windows Storage Server 2008 R2 operating system.
Device views
There are several LEDs on the front and rear of the chassis. The
LEDs show the over-all status of the system and the activity and
health of specific components.
2
2.1
10 en | System overview DIVAR IP 2000
2013.09 | V4 | DOC Bosch Sicherheitssysteme GmbH
Altri manuali per DIP-2040-00N
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Bosch Sistema di sicurezza
Bosch
Bosch ISW-BMC1-M82X Come usare
Bosch
Bosch LTC 9441 Series Manuale utente
Bosch
Bosch SOLUTION 6000 Manuale utente
Bosch
Bosch PVA-1EB Manuale utente
Bosch
Bosch Solution 6000-IP Manuale utente
Bosch
Bosch APC-AMC2-4W Manuale utente
Bosch
Bosch AMC UL1 Manuale utente
Bosch
Bosch PVA-1EB Manuale utente
Bosch
Bosch FMM-100 Series Manuale utente
Bosch
Bosch MIC IP starlight 7000i Manuale utente
Bosch
Bosch DIVAR DIP-6080-00N Manuale utente
Bosch
Bosch Plena Power Amplifier Istruzioni per il montaggio
Bosch
Bosch DIP-6083-8HD Manuale utente
Bosch
Bosch B Series Manuale utente
Bosch
Bosch FMC-210-DM-G-B Manuale utente
Bosch
Bosch DIVAR IP 3000 Manuale utente
Bosch
Bosch Security System Manuale utente
Bosch
Bosch Carephone 61 Manuale utente
Bosch
Bosch DIP-2040-00N Manuale utente
Bosch
Bosch D1260 Series Manuale utente
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente