Brink Air Control Guida di riferimento

Installation regulations

Brink Air Control

English

Contents

1 User manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Descripon Brink Air Control. . . . . . . . . . . . . . . . . . . 3

1.2 Symbols used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Technical specicaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 General product specicaon. . . . . . . . . . . . . . . . . . 4

2.2 Environment inuences. . . . . . . . . . . . . . . . . . . . . . . 4

2.3 Overview operaonal controls. . . . . . . . . . . . . . . . . 4

2.4 Overview display version main screen. . . . . . . . . . . 4

2.5 Venlaon modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Precauonary measures and safety instrucons. . . . . . . 5

3.1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.2 During placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.3 During use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.4 During maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.5 For the environment. . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Assembly and installaon (to be performed by the

installer). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.1 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.1.1 Disconnecng the operaonal module from the

wall bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.1.2 Mounng the wall bracket. . . . . . . . . . . . . . . . . 7

4.1.3 Electrical connecon. . . . . . . . . . . . . . . . . . . . . 7

4.1.4 Replacing the operaonal module in the wall

bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.2 Installaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.2.1 Seng language. . . . . . . . . . . . . . . . . . . . . . . . . 8

4.2.2 Seng me. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.2.3 Seng date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.2.4 Selecng a device connected to the Brink Air

Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Descripon of operaon; manner of use. . . . . . . . . . . . 11

5.1 Navigaon: general descripon. . . . . . . . . . . . . . . . 11

5.2 Selecng a device connected to the Brink Air Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.3 Weekly programmes P1, P2 and P3. . . . . . . . . . . . 11

5.3.1 Standard sengs P1, P2 and P3. . . . . . . . . . . 11

5.3.2 Creang a P1 programme. . . . . . . . . . . . . . . . 12

5.3.3 Creang a P2 programme. . . . . . . . . . . . . . . . 13

5.3.4 Creang a P3 programme. . . . . . . . . . . . . . . . 14

5.4 Acvang programma type (P1, P2 or P3). . . . . . . 16

5.5 Temperarily overriding progranmme. . . . . . . . . . . 16

5.6 Overriding programme for a longer period of me 16

5.7 Seng venlaon mode values. . . . . . . . . . . . . . . 17

5.8 Retrieving sengs. . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.9 Factory seng connected device. . . . . . . . . . . . . . 18

6 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.1 General maintenance. . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 Cleaning or replacing lter. . . . . . . . . . . . . . . . . . . . 19

6.2.1 Filter nocaon. . . . . . . . . . . . . . . . . . . . . . . 19

6.2.2 Removing, cleaning or replacing. . . . . . . . . . . 19

6.2.3 Re-seng lter nocaon. . . . . . . . . . . . . . . 19

7 Dismanteling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8 Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

9 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10 Troubleshoong and quarantee. . . . . . . . . . . . . . . . . . 23

10.1 Troubleshoong. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

10.2 Quarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

11 Appendix 1: Standard sengs weekly programmes. . 24

11.1 Standard programme P1. . . . . . . . . . . . . . . . . . . . 24

11.2 Standard programme P2. . . . . . . . . . . . . . . . . . . . 25

11.3 Standard programme P3. . . . . . . . . . . . . . . . . . . . 26

11 Appendix 2 Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

11.1 Image overview operaonal control. . . . . . . . . . . 27

11.2 Image overview display. . . . . . . . . . . . . . . . . . . . . 27

11.3 Image venlaon modes. . . . . . . . . . . . . . . . . . . . 28

11.4 Image disconnecng operaonal module. . . . . . 28

11.5 Image electrical connecon. . . . . . . . . . . . . . . . . . 28

11.6 Image wall bracket. . . . . . . . . . . . . . . . . . . . . . . . . 29

11.7 Image replacing operaonal module. . . . . . . . . . 29

11.8 Image lter nocaon. . . . . . . . . . . . . . . . . . . . . 30

11.9 Image main menu display. . . . . . . . . . . . . . . . . . . 30

11.10 Image reseng lter. . . . . . . . . . . . . . . . . . . . . . 31

11.11 Image device informaon menu. . . . . . . . . . . . . 32

11.12 Image basic sengs. . . . . . . . . . . . . . . . . . . . . . . 33

11.13 Image installer menu. . . . . . . . . . . . . . . . . . . . . . 34

1 User manual

Dear client,

Thank you for buying the Brink Air Control. This user’s manual contains all required information to quickly

become familiar with the product. We kindly request you to carefully go through this information before using the

product.

This user’s manual is intended for the Brink Air Control installer and end user. You can retrieve the required

information from the user’s manual via the table of contents.

This is an extended user’s manual. A Quick Start Guide is available, in addition to this user’s manual.

Take good care of this user’s manual!

For more information or ordering manuals, please contact:

Brink Climate Systems B.V.

Mailbox 11

NL-7950 AA, Staphorst, The Netherlands

T: +31 (0) 522 46 99 44

F. +31 (0) 522 46 94 00

E. info@brinkclimatesystems.com

www.brinkclimatesystems.com

1.1 Description Brink Air Control

Intended and unintended use

The Brink Air Control should be used in combination with products that have been approved by Brink Climate

Systems B.V..

Brink Climate Systems B.V. cannot be held responsible for possible damage caused by improper, incorrect or

unwise use. It is important that one understands this user’s manual completely.

Working with other devices

The Brink Air Control is connected to other devices. The HRU (Heat Recovery Unit) is co-dependent on these

devices’ operation for its proper functioning. These devices’ presence and proper functioning are prerequisites for

using the Brink Air Control.

1.2 Symbols used

Warning!

The user can (seriously) injure himself or seriously damage the product.

A warning is indicative of a risk of damage to the user or product, if the user does not execute

the procedures carefully.

Careful!

The product can be endangered. “Careful” is indicative of a risk of damage to the product, if the

user does not execute the procedures carefully.

Take note!

A remark with supplementary information for the user. A remark draws the user’s attention to

possible problems.

Brink / 3Brink Air Control 614884-A

2 Technical speciﬁcation

2.1 General product speciﬁcation

Product description

Name: Brink Air Control

Model/ Type: Brink Climate Systems B.V.

Technical product speciﬁcations

Electricity: 15 to 24 Volt

Power consumpon: 1,5 Wa

Protecon class: IP30

Power reserve: > 48 hours

Ambient conditions

Ambient temperature: 0 °C to 50 °C

Storage temperature: -20 °C to 60 °C

Humidity: 10% to 90%

Other: Exclusively for indoor use

2.2 Environment inﬂuences

The Brink Air Control should be placed and used in a space with the correct ambient conditions for proper

operation. The Brink Air Control may only be mounted on the indoors, but not on the vicinity of a heat source, a

radiator, in a draft or in a humid environment. The Brink Air Control may also not be exposed to direct radiation

heat (sun light). The Brink Air Control may also not be mounted in the vicinity of a magnetic ﬁeld. This could

damage internal components.

2.3 Overview operational controls

The Brink Air Control has a number of buttons with which the device can be operated: (®Image overview

operational control page 27)

2.4 Overview display version main screen

(® Image overview display page 27)

2.5 Ventilation modes

The Brink Air Control has four ventilation modes (®Image ventilation modes page 28). You can activate a

ventilation mode yourself (for more information see ®Description of operation; manner of use page 11 ). You can

adjust every ventilation mode yourself (for more information ®Setting ventilation mode values page 17 ). You can

retrieve the set values at the Device information menu (see ®Image basic settings page 33 and ®Retrieving

settings page 18 ).

Brink Air Control 614884-A

3 Precautionary measures and

safety instructions

3.1 General

Warning!

The installation and assembly activities required to commission your Brink Air Control should be

performed by an installer approved by Brink Climate Systems B.V..

Warning!

Immediately remove the power from your Brink Air Control by removing the connected device’s

plug from the socket, if:

·Parts of the Brink Air Control lie open, are pierced or had fallen hard;

·The power cable is damaged;

·The screen is cracked or broken.

Then contact Brink Climate Systems B.V. or you supplier.

Take note!

Never use parts other than original parts.

Take note!

Only use the Brink Air Control indoors, at temperatures between 0 °C and 50 °C and with a relative

humidity between 10% and 90%.

Take note!

All settings (excluding the ﬁlter message) will be lost if the Brink Air Control breaks down or if the

factory settings are reset. There is no backup available.

3.2 During placement

Take note!

Assembly and installation should be performed by an installer approved by Brink Climate Systems

B.V.. The following requirements should be taken into account during placement:

·The Brink Air Control should be placed at a height of approximately 1.65 meters above the ﬂoor;

·The Brink Air Control may not be covered, for example, by a curtain or a cabinet;

·Consult paragraph ®Environment inﬂuences page 4 for environmental requirements.

Brink / 5Brink Air Control 614884-A

3.3 During use

Take note!

Settings, which have not been described in this user’s manual, are intended for installers

approved by Brink Climate Systems B.V.. Do not change these by yourself.

3.4 During maintenance

Careful!

Clean the screen with a soft cloth.

Careful!

Never apply water and/or (cleaning) liquid to the screen.

3.5 For the environment

Take note!

The Brink Air Control may not be removed as unsorted urban waste, but should be treated

separately.

Take note!

Make enquiries within your own region, where the Brink Air Control can be handed in when

use has been terminated. Do not throw away electrical devices or parts, but check if (parts

of) the Brink Air Control cannot be handed in, recycled or re-used.

Brink Air Control 614884-A

4 Assembly and installation (to be

performed by the installer)

Assembly and installation should be performed by an installer approved by Brink Climate Systems B.V..

4.1 Assembly

You should perform the steps, described in paragraph (®Disconnecting the operational module from the wall

bracket page 7)through paragraph (®Replacing the operational module in the wall bracket page 8), one by one,

to assemble the Brink Air Control.

4.1.1 Disconnecting the operational module from the wall bracket

Disconnect the operational module from the wall bracket. Perform the following actions ( ®Image disconnecting

operational module page 28 ):

·Slide the control unit upward over the two guide proﬁles of the wall bracket until the control

unit can be taken off.

4.1.2 Mounting the wall bracket

The wall bracket can be aached to a wall box (Ø 55 mm) or can be directly mounted on the wall with screws and plugs.

·Screw the wall bracket onto the wall in the correct position. Here one must use the mounting holes

in the wall bracket (®Image wall bracket page 29).

Take note!

Consult ( ®During placement page 5) for more information on placing the Brink Air Control.

4.1.3 Electrical connection

The following actions should be performed to connect the Brink Air Control electrically ( ®Image electrical

connection page 28 ):

·Feed the two-core wire (from the device to be connected) through via opening at the back of the

wall bracket.

·Check that the cables’ ends have been stripped in the correct manner. If this is not the case, do so.

·Screw the cable to the terminal No. 1 and No. 2. Consult the installation instructions of the device

to be connected, for more information on the correct connection.

Brink / 7Brink Air Control 614884-A

4.1.4 Replacing the operational module in the wall bracket

Place the operational in the wall bracket mounted on the wall. Perform the following actions for this ( ®Image

replacing operational module page 29 ):

·Slide the control unit downward over the two guide proﬁles. Make sure the guide proﬁles of the wall bracket ﬁt snugly in the cutouts of the control unit provided for that purpose.

Take note!

The operational module should click onto the wall bracket. Only then is a proper electrical connection established.

4.2 Installation

4.2.1 Setting language

You can set the language in which the menus are presented. Perform the following actions to set the language

(see ®Image overview operational control page 27 , ®Image overview display page 27 & ®Image basic

settings page 33 ):

·Press returnkey "2" as many times as necessary to get to the main screen

·Press setting knob "1"; ‘Main Menu’ opens

·Select ‘Basic Settings’ by turning setting knob "1"

·Press setting knob "1";‘Basic Settings’ opens

·Select ‘Language’ by turning setting knob "1"

·Press setting knob "1"; ‘Language’ opens

·Select the desired language by turning setting knob "1"

·Press setting knob "1" to set the selected language

·Press returnkey "2" as many times as necessary to get to the main screen

Take note!

The names of the described menu items will not correspond with this user manual’s menu items if

the Brink Air Control is set to a language other than Dutch.

Brink Air Control 614884-A

4.2.2 Setting time

You can set the time. The time is visible on the main screen The Brink Air Control only has 24 hour

representation. Perform the following actions to set the time ( ®Image overview operational control page 27 ):

·Press returnkey "2"as many times as necessary to get to the main screen

·Press setting knob "1"; ‘Main Menu’ opens

·Select ‘Basic Settings’ by turning setting knob "1"

·Press setting knob "1"; ‘Basic Settings’ opens

·Select ‘Clock’ by turning setting knob "1"

·Press setting knob "1"; ‘Clock’ opens

·Change the time by turning setting knob "1"

·Press setting knob "1" to conﬁrm the time

·Repeat the previous two steps for both the minutes and seconds

·Press returnkey "2" as many times as necessary to get to the main screen

4.2.3 Setting date

You can set the date. The date is visible on the main screen. Perform the following actions to set the date(see ®

Image overview operational control page 27 , ®Image main menu display page 30 & ®Image basic settings

page 33 ):

·Press returnkey "2" as many times as necessary to get to the main screen

·Press setting knob "1"; ‘Main Menu’ opens

·Select ‘Basic Settings’ by turning setting knob "1"

·Press setting knob "1"; ‘Basic Settings’ opens

·Select ‘Date’ by turning setting knob "1"

·Press setting knob "1" ‘Date’ opens

·Change the day by turning setting knob "1"

·Repeat the previous two steps for both the months and the year

·Press returnkey "2" as many times as necessary to get to the main screen

Brink / 9Brink Air Control 614884-A

4.2.4 Selecting a device connected to the Brink Air Control

You can choose the device you want to regulate with the control if multiple devices are connected to Brink Air

Control. Proceed as follows to set the appliance selection (see ®Image overview operational control page 27 &

®Image installer menu page 34 ):

·Press returnkey "2" as many times as necessary to get to the main screen

·Press setting knob "1"; ‘Main Menu’ opens

·Select ‘Installer’ by turning setting knob "1"

·Press setting knob "1";‘Installer’ opens

·Select ‘Device’ by turning setting knob "1"

·Press setting knob "1" to conﬁrm selected device

If only one appliance is connected, no choice is offered and only Heat Recovery Unit appliance is displayed.

Brink Air Control 614884-A

Altri manuali per Air Control

Indice

Altri manuali Brink Unità di controllo

Brink

Brink WTW Manuale utente

Brink

Brink WTW Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente