Broadata Link Bridge LBC-PSW84 Manuale utente
LBC-PSW84
LINK BRIDGETM MULTI-FORMAT
PRESENTATION SWITCH
BCI reserves the right to make changes to the products described herein without prior
notice or consent. No liability is assumed as a result of their use or application. All
rightsreserved.
©2013 Broadata Communications, Inc.
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASE OBSERVE THE FOLLOWING SAFETY
PRECAUTIONS
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
Broadata Technical Support, (800) 214-0222
4
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION ..............................................5
2.0 OPERATION CONTROLS AND FUNCTIONS .................7
2.1 FRONT PANEL .................................................................7
2.2 REAR PANEL ...................................................................8
2.3 REMOTE CONTROL......................................................10
3.0 ON SCREEN DISPLAY...................................................11
3.1 MAIN MENU SELECTION ..............................................11
3.2 COLOR ...........................................................................12
3.3 AUDIO .............................................................................13
3.4 SETUP............................................................................14
3.5 INFORMATION................................................................15
4.0 CONNECTOR PIN ASSIGNMENT .................................16
4.1 IR PINASSIGNMENT .....................................................16
4.2 RS-232 PIN ASSIGNMENT.............................................17
5.0 DC POWER CONNECTION ...........................................18
6.0 MAINTENANCE AND TROUBLESHOOTING ...............20
6.1 MAINTENANCE ..............................................................20
6.2 TROUBLESHOOTING ...................................................20
7.0 SPECIFICATIONS...........................................................22
8.0 SERVICE PROCEDURE ................................................23
8.1 REPLACEMENT POLICY ..............................................23
8.2 RETURN AND REPAIR SERVICE .................................23
9.0 LIMITED WARRANTY ....................................................24
10.0 APPENDIX A.................................................................25
11.0 APPENDIX B..................................................................28
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
1.0 PRODUCT DESCRIPTION
TheLBC-PSW84 is an HDBaseT™ capable8 by 4 Digital Presentation
Scalerthatcan switch and scale HDMI/HDBaseT/PC/Composite Video
signalsfrom any one of its eight inputsand simultaneously display it on
any of its HMDI or HDBaseT outputs. The unit supports four (4) HDMI
input,one(1) VGA input, one (1)compositeinput and two (2) HDBaseT
inputs. The unit has an HDMI bypass output, allowing local monitoring
of any of the HDMI or HDBaseT inputs, VGA and composite are not
supported by the bypass output.
Ithas theaddedbenefitofcontrolviaIR remotecontrol,RS-232,IP/Telnet
andWebGUI, with all information includingsystem status presented on
its comprehensive OSD (On Screen Display).
TheLBC-PSW84 features full 5play™ compliance for easy integration
with compatible transmitters and receivers. The LBC-PSW84 is
compatiblewithour Designer and Standard(LBH& LBC model) Series
transmitters and receivers. This makes both CAT-5e/6 transmission
and HDMI/DVI/VGA/YPbPrI conversion in one single system setup.
The units are easily monitored by a power/ link LED indicators.
Figures 1-1, and 1-2 below illustrate the front and rear panels of the
LBC-PSW84 unit and Figure 1-3 shows the remote control.
Features
• HDMI,HDCP and DVI compliant
• Full 5Play™ compliant: Video, Audio, LAN, and Control (IR &
RS-232 bypass)
• Supports Power over HDBaseT (PoH) on the CAT5e/6/7
output to a compatible Receiver. HDBaseT inputs do not
supportPoH
• Supports High-definition Audio: LPCM 7.1CH, Dolby TrueHD,
Dolby Digital Plus and DTS-HD Master Audio transmission
(32-192kHz sample rate)
• Supports distances of up to 100 meters on the output and
100m on the input over industry standard CAT5e/6/7 cable
• Supports scaling of any input signals to a wide range of HDTV
and PC output resolutions up to 1080p and WUXGA (RB)
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
Broadata Technical Support, (800) 214-0222
6
• Simultaneous video output of the selected source through the
HDBaseT and HDMI outputs and audio output through the
digital coaxial and analog L/R outputs
• Features four HDMI inputs with corresponding L/R audio
inputs (3.5mm mini-jack), two HDBaseT CAT5e/6/7 inputs, PC
(15-pin D-Sub) with L/R audio (3.5mm mini-jack) and
Composite Video and L/R audio (3 RCA)
• Features two HDMI outputs, one HDBaseT CAT5e/6/7 output,
one Digital Coaxial audio output and one L/R audio 3.5mm
mini-jackoutput
• Supports a switchable HDMI scaler bypass output, allowing
local monitoring of any of the HDMI or HDBaseT inputs, VGA
and composite inputs are not supported by this output.
• Supports control via IR, Remote control, local RS-232,
Telnet WebGUI and on-panel controls
•SupportsHDBaseT LAN pass-through function tocompatible
Receivers
Package Contents
• 1 x 8 by 4 Presentation Switch w/ Scaler
• 1 x IR Extender cable
• 1 x IR Receiver cable
• 1 x Remote Control w/ battery
• 1 x 24v/2.7A DC PowerAdapter
• 1 x Power Cord
• User’sManual
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
2.0 OPERATION CONTROLS AND FUNCTIONS
2.1 Front Panel
1. POWER: Press this button to turn ON the device and the LED
willilluminate.
2. IR Window: This IR receiver receives only the remote control
signal from the packaged remote control.
3. INPUT HDMI 1~4 & LED: Press the IN buttons to select an
input source signal from the 4 HDMI input sources to be
display for output ports. The LED will illuminate according to
theselection.
4. BYPASS & LED: Press these buttons to select an input
source signal from the 6 input sources to be displayed for
BYPASS output port. The LED will illuminate according to the
selection.
5. INPUT CAT5e/6/7 5~6 & LED: Press the IN buttons to select
an input source signal from the 2 CAT5e/6/7 input sources to
be display for output ports. The LED will illuminate according
to the selection.
6. INPUT VGA & LED: Press this button to select VGA input
source signal to be display for VGA output port. The LED will
illuminate according to the selection.
7. INPUT CV & LED: Press this button to select CV input
source signal s to be display for CV output port. The LED
will illuminate according to the selection.
8. MENU: Press this wheel to enter into the menu and press it
again to confirm the selection.
1235678910
44
3567
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
Broadata Technical Support, (800) 214-0222
8
9. +/-: Press these buttons to move up/down under menu
selection or under volume control to adjust audio volume up/
down.
ENTER: Press this button to confirm menu selection
2.2 Rear Panel
1. IR OUT: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
2. IR IN: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct
line-of-sight of the IR Extender.
3. OUTPUTCAT5e/6/7: Connect to the Receiver unitwithaSingle
CAT5e/6/7 cable for transmission of all data signals.
4. OUTPUT HDMI: Connect to a HDMI equipped TV/monitor for
display of the HDMI input source signal.
5. OUTPUT COAX: Connect to audio sound equipment such as
speaker or amplifier for audio sound output.
6. OUTPUTAUDIO: Connect to audio sound equipment such as
speaker or amplifier for audio sound output. This audio is
extracted from the video output. The source for this audio is
dependent upon the selected mode from the OSD. If in ‘Auto’
mode then the source audio is derived from the input HDMI
embedded audio. If in ‘EXT’ mode the audio is sourced from
theexternal input audio.
4
37910
12567813 14 16
11 12 15 17
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
7. SERVICE 1& 2: These slots are reserved for firmware update
use only.
8. DSP PROG Switch: This switch is reserved forfirmwareupdate
use only.
9. BYPASS OUTPUT: Connect to a HDMI equipped TV/monitor
or DVI equipped monitor with audio sound equipment such as
speaker for both video and audio output display. This output
bypasses the output scalar and directly follows the resolution
of the selected input. The Bypass audio connector does not
extract or de-embed audio from the HDMI video. The Bypass
audio is only sourced from the external audio inputs. The
embedded audio on the Bypass HDMI video is only sourced
from the embedded audio on the HDMI video inputs.
10.INPUT HDMI 1~4 & AUDIO 1~4: Connect to HDMI source
equipmentsuchas DVDorBlu-rayplayeralong ortoDVIsource
equipmentalong with audio source signal.
11. INPUT CAT5e/6/7: Connect this port to HDMI to CAT5e/6/7
Transmitter with CAT5e/6/7 cable to extend the signal up to
100m.
12. INPUTPC&AUDIO: Connect this port toPC/Laptopwithaudio
signalfor input signal selecting. . The PC(VGA) input does not
support YPbPr video format
13.INPUTCV:Connect thisporttosourceequipmentsuch as video
player or Set-Top-Box for input signal selecting.
14. RS-232: ConnectfromPC/Laptop forRS-232commandsending
to control the device.
15.LAN: Connect from PC/Laptop with active internet service for
Web
16.POWER Toggle: Switch this toggle to turn ON and OFF the
device’s power
17.DC 24V: Connect the adaptor with power cord included in the
package and connect toAC wall outlet for power supply.
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
Broadata Technical Support, (800) 214-0222
10
2.3 Remote Control
1. POWER: Press this button to switch the device ON or to put
the device into Standby mode.
2. MUTE: Press this button to mute output audio sound.
3. INPUT: Press these buttons one time each to select input
source for outputs display.
4. MENU: Press this button to enter into the OnScreen Menu.
5. EXIT: Press this button to exit menu selection.
6.
& OK: Press OK to confirm the selection or use the
directional buttons to navigate the On-Screen-Menu.
7. ADJUST: Press this button when output image is not fitting the
display’sscreen perfectly.The device will autoadjusttheimage
to full screen.
8. RESET: Press thisbuttonto set the device back intothefactory
default setting.
9. BYPASS: Press these buttons to select an input source for
Bypass output port to display.
1
2
3
56
7
8
9
4
LBC-PSW84 User’s Manual
LinkBridgeTM Multi-formatPresentation Switch
3.0 ON SCREEN DISPLAY (OSD) MENU
3.1 Display Selection: Output, Size, Mode Info, Input
HDCP
OUTPUT: 640x480 60, 800x600 60, 1024x768 60 , 1360x768
60, 1280x720 60, 1280x800 60, 1280x1024 60, 1440x900 60,
1400x105060, 1680x1050 60, 1600x1200 60,1920x1080 60,
1920x1200 60, 720x480P 60, 1280x720P 60 (Factory Default
upon reset), 1920x1080I 60, 1920x1080P 60 (setting upon
shipment), 720x576P 50, 1280x720P 50, 1920x1080I 50,
1920x1080P50
SIZE: OVERSCAN, FULL (Factory Default upon reset),
FOLLOW INPUT, PANSCAN, LETTERBOX, UNDER 2,
UNDER1
MODE INFO: INFO, ON, OFF
INPUT HDCP: OFF, ON
PC (PC Mode Only):AUTO SETUP, PC MODE ONLY 0 ~ 60,
V_POSITION 0 ~ 60, PHASE 0 ~ 31, CLOCK, XGA/WXGA
(Factory default), DEFAULT Yes/No (Factory default).
Indice
Altri manuali Broadata Interruttore
