BTC BCO5216IA Manuale utente
Dual Digital Drive
COMBO 5216IA
User’s Manual
DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT
EXPOSURE TO BEAM
VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET
NICHT DEM STRAHL AUSSETSEN
ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
EVITER TOUTE EXPOSITION AUX RAYONS.
Copyright Statement
It is a criminal offence, under applicable copyright laws, to make unauthorised
copies of copyright-protected material, including computer programs, films,
broadcasts and sound recordings. This equipment should not be used for such
purposes.
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASER KLASSE 1
LUOKAN 1 LASERLAITE
PRODUIT LASER
CATEGORIE 1
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The drive is in conformity with the EMC directive and low-voltage directive.”
Table of Contents
INTRODUCTION 1
SYSTEM REQUIREMENTS 2
PACKAGE CONTENTS 2
INSTALLATION 3
HOST INTERFACE CONNECTIONS 3
HARDWARE INSTALLATION 4
DRIVER INSTALLATION 6
SOFTWARE INSTALLATION 9
DVD REGION CODE 11
OPERATION & CONNECTION 13
FRONT PANEL 13
REAR VIEW 15
TECHNICAL DATA 17
Dual Digital Drive
1
INTRODUCTION
Welcome to a multimedia world of CD-ReWritable technology, DVD-ROM
capabilities and, memory card compatibility!
This compact and high-performance COMBO 5216IA frees up precious bay
space and presents you as an IDE Combo (CD-RW+DVD ROM) Drive and
a USB-connected card reader. It reads CDs of all types at maximum 52X
speed, and DVD-ROMs at maximum 16X speed. For the writing ability, it
writes to CD-Rs at up to 52X speed, and to CD-RWs at up to 24X speed.
Other than that, the built-in 7 in 1 card reader which offers read-write ability
of 7 memory card types simplifies the process of exchanging data between
Digital cameras, voice recorders, PDAs, MP3s… and your computer.
With this multi-functional solution and the bundled software package, you
can view, archive, or write files/photos/video/music directly from the drive
and enjoy the fascinating digital as well as the DVD entertainment on your
desktop.
Here are some important features of this Combo Drive:
♦ Easy installation with Combo drive of IDE and card reader of USB
1.1 interface (on board connection)
♦ 8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R
media
♦ 4X, 10X, 12X, 16X and 24X writing speed on CD-RW media
♦ Adopts “MTKSuperLink” to prevent Buffer Underrun
♦ Supports writing modes of TAO, DAO, SAO and packet writing
♦ Supports MultiRead function
♦ Four-slot integration works with CompactFlash, MicroDrive,
Memory Stick, Memory Stick Pro, MultiMediaCard, Secure Digital,
and SmartMedia
Dual Digital Drive
2
♦ Smooth DVD playback
System Requirements
For IBM compatible PCs, the system requirements recommended are as
follows:
♦ Pentium II, Celeron 400MHz or above with at least 64MB of
memory
♦ Fast and sufficient hard disk space (minimum 200MB for
installation, 1GB or more is recommended.)
♦ IDE host interface supporting ATAPI MMC command & USB host
interface (if you don’t have USB on-board connection)
♦ Microsoft Windows 98SE/2000/ME/XP
Package Contents
The package contains the following items:
♦ Dual Digital Drive, COMBO 5216IA
♦ Audio cable
♦ 2 Application software discs
♦ 4pcs of screws/bag
♦ Quick Installation Guide
♦
Dual Digital Drive
3
INSTALLATION
Host Interface Connections
Most current mainboard models have two IDE ports (primary and
secondary), which can connect two IDE cables. Two IDE cables allow you
to connect up to four devices, but it is recommended that you separate IDE
ports for your hard drive and your Dual Digital Combo Drive. This will
ensure that your hard drive’s performance and speed won’t be affected by
having the drive on the same cable.
Jumper Setting
On the rear panel of this drive, you will find three pairs of jumpers: CS
(CSEL), SL (Slave) and MA (Master). Use the jumper cap to set the device
to CS, SL or MA mode corresponding to your PC configuration. If you
connect only one device on the IDE cable, you can set the jumper as
“MASTER” or “SLAVE”.
If you connect two devices on the same cable, set different jumper for each
device (one as “MASTER”, and the other one as “SLAVE”). The same rule
applies to the connection of having your hard disk and another device on
the same cable.
Dual Digital Drive
4
MASTER
CSEL
SLAVE
JUMPER
Improper or conflicting setting will cause the unit not detected by your
system.
Hardware Installation
1. Turn off the power to your computer system.
2. Disconnect the power cord and all cables from the back of your
computer, and then remove the cover of the computer.
3. Insert the drive into one of the vacant 5.25" drive bays and
secure it to your PC with all four mounting screws.
4. Connect one end of the 40-pin IDE cable to the IDE connector of
this drive and the other end to the IDE port on your mainboard.
Also, connect the power supply cable to the back of the drive.
Power In
Make sure to align and connect the red-edge of the IDE Cable to
Pin 1 on the drive.
Dual Digital Drive
5
5. If you have a sound card that can be connected to the drive, you
can also connect the drive (as Audio-Out) and the sound card (as
Audio-in) with a 4-pin audio cable.
If your mainboad is integrated with built-in sound system, plug the
4-pin audio cable into the CD-IN connector on the mainboard as
Audio-in.
6. Connect the USB cable at the back of the drive to the USB
header on the computer’s mainboard. The red wire of the cable
needs to be plugged into Pin 1 on the board. If the connection is
correct, the lower LED on the front panel will light Yellow.
This drive supports USB 1.1 and if you connect to USB 2.0
connector, only transfer rate of USB 1.1 will be available.
Signal
Red/Vcc
Pin #
1
Mainboard
USB
RED WIRE
IDE
RED WIRE
USB Header
White/D-
Green/D+
Black/Ground
Braided Shield Ground
2
3
4
5
7. Re-attach the cover of the computer, and reconnect the power
cord and all cables to the computer.
Dual Digital Drive
6
Driver Installation
For the Combo Drive
For the Combo Drive itself, it’s an IDE device supporting Plug & Play and
Windows 98SE/ME/2000/XP can automatically detect the drive and load
the appropriate driver.
For the Card Reader
Windows 98SE/2000
If you are using Window 98SE or 2000, please install the provided driver.
1. Insert the application disc.
2. Select:\Card Reader Driver
3. Click “setup.exe”, and follow the on-screen instructions:
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BTC Unità DVD
BTC
BTC BDV 316E Manuale utente
BTC
BTC BCO4016IM Manuale utente
BTC
BTC BCO5232UI Manuale utente
BTC
BTC BCO4816IM Manuale utente
BTC
BTC BCO5216IB Manuale utente
BTC
BTC BCO5232IB Manuale utente
BTC
BTC BCO4816UI Manuale utente
BTC
BTC BCO 5216UI Manuale utente
BTC
BTC DRW1108UB Manuale utente
BTC
BTC BCO5232IM Manuale utente
