CABAC C6500 Manuale utente
LOOP CALIBRATOR
INSTRUCTION MANUAL
C6500 Cabac 4-20mA and 0-10V source.
Table of Contents
Introduction..............................................1.
Safety Notes.............................................2.
Features...................................................3.
Specication.............................................4.
Panel Description.....................................5.
Display......................................................6.
Functions.................................................7.
Operating Instruction8.
mA Output Selection............................A.
Percentage(%) Input............................B.
Adjusting the Percentage Up andC.
Down....................................................
Auto Step Function..............................D.
Auto Ramp Function............................E.
0~24V Voltage Output..........................F.
Voltage Output(0-24V)........................G.
Use the AC Adapter..................................9.
Replacing the Battery.............................10.
1
1
1
2
3
4
5-7
8-9
10-11
12-13
14-15
16-17
18
19
20
20
-1-
Introduction1.
This tester has been designed and tested in accordance
with the CE safety requirements for electronic measuring
apparatus EN61326-1 and other safety standards. Follow
all warnings to ensure safe operation.
Safety Notes2.
Read the following safety information carefully●
before attempting to operate or service the
meter.
Use the meter only as specied in this ●
manual. Otherwise, the protection provided
by the meter may be impaired.
Rated enviromental conditions:●
(1) Indoor use.
(2) Installation Category I
(3) Pollution Degree 2.
(4) Altitude up to 2000 meters.
(5) Relative humidity 80% max.
(6) Ambient temperature 0~40℃.
Features:3.
(1) 4-20mA (1KΩ load, 24V Loop Supply)
(2) 0.025% Basic Accuracy
(3) Simple Operation Interface
(4) Auto Ramp and Step Functions
(5) 0-20mA, 0-24mA selectable
(6) Incremental percentage setting: 0-100%
(7) Warning beeper when output is open
(8) 0-24 V output
-2-
Specication (254. ℃±5℃≤85%R.H.)
DC CURRENT (1kΩ Max Load, 24v Loop Supply)
RANGE RESOLUTION ACCURACY
0-4mA 1uA ±0.025%±10uA
4-20mA 1uA ±0.025%±5uA
20-24mA 1uA ±0.025%±5uA
DC VOLTAGE
RANGE RESOLUTION ACCURACY
0-4V 1mV ±0.05%±10mV
4-20V 1mV ±0.05%±5mV
20-24V 1mV ±0.05%±5mV
GENERAL
Power Consumption 150mA at 24V 1kΩ load
Operating Temperature 0º C - 50º C
Operating Humidity ≤80% R.H.
Storage Temperature -10º C - 60º C
Storage Humidity ≤85% R.H.
Power Source 9V x 1 alkaline battery
Dimensions 160 (L) x 100 (W) x 38 (D) mm
Weight Approx. 350g (battery includ-
ed)
Accessories DC adapter, pouch, battery,
instruction manual
-3-
Panel Description5.
1.LCD Display 6.ENTER Button
2.ON/OFF Button 7.Numerical & Function Keypad
3.Shift Button 8.DC Adaptor Input Socket
4.Voltage Button 9.Stand
5.Current Button 10.Output Terminal
4-20mA LOOP CALIBRATOR
123
4-20mA
4
7 8
0
9V
I
START 5
END
%
%
-+
6
SEC.
ENTER
Shift
0-20mA 0-24mA
ON
OFF
%
1.
7.
6.
2.
8.
9.
3.
4.
5.
10.
-4-
Display6.
1.mVA: Units
2.0-20mA: Output Range of mA
3.%: Percentage
4. : Ramp
5. : STEP
6.OL: Overload, output open
7.SHIFT:SHIFT functions
8. : low Battery
1.
2. 3.
4.
5.
6.
7.8.
-5-
Functions7.
Power ON/OFFa.
Press the SHIFT button and select the desired mAb.
range by pressing one of these three buttons.
Press the SHIFT button then press START (#4) buttonc.
to begin Auto Ramp Function.
Press the SHIFT button then press the END (#5)d.
button to stop Auto Ramp Function.
123
4-20mA
4
7 8
0
9V
I
START 5
END
%
%
6
SEC.
ENTER
Shift
0-20mA 0-24mA
ON
OFF
%
-6-
Press the SHIFT button then press the SEC. (#6)e.
button to enter the duration in seconds for Auto Ramp
Function.
Press the SHIFT button then press this button (#7)f.
to begin Auto Ramp Function. Press again to end Auto
Ramp Function.
Press the SHIFT button then press the % button tog.
select the percentage range.
After the percentage range has been entered,use
these / buttons to increase or decrease the
percentage incrementally.
Press the SHIFT button then press this button (#9) toh.
start the STEP function. Press again to stop the function.
-7-
Press ENTER button to accept entry of numbers.i.
Press the SHIFT button then press V to change toj.
Voltage setting.
Press the SHIFT button then press the I button tok.
return to mA (current) setting.
-8-
Operating Instruction8.
mA Output Selection:A.
Insert the test leads to the black and red terminals1.
on the calibrator accordingly.
Connect the leads to the device under test.2.
Press the On/Off button.3.
The device automatically defaults on the 4-20mA4.
range. Press the SHIFT button and select one of
the desired range buttons: 1, 2 or 3. The selected
range will be displayed on the LCD.
NOTE: A maximum of 5 digits can be entered. If < 5 digits
(1 to 4) are entered, you must press the ENTER button
to accept end of entry. If > 5 digits, the calibrator will
automatically accept the entry and the output specied
current.
4-20mA LOOP CALIBRATOR
123
4-20mA
4
7 8
0
9V
I
START 5
END
%
%
-+
6
SEC.
ENTER
Shift
0-20mA 0-24mA
ON
OFF
%
4.000mA
Indice
Altri manuali CABAC Apparecchiature di prova
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
